Post Buy Requirement
AT
United States
Add Review

Our Products

CANFLEX CAMMPROFILE STYLE 942A

Manufactured from solid metal, Cammprofile gaskets exhibit all the desirable qualities of a solid metal gasket with the added advantages of a reduced area of contact thereby reducing the bolt stress required to make a seal. Grafoil tape is added to the sealing surface for improved sealability. Because of their ability to seal on less than perfect flange faces, Cammprofile gaskets are often chosen as a replacement to traditional double-jacketed heat exchanger gaskets.
View Complete Details

CANFLEX HIGH TEMP

CANFLEX High Temp gasket material can be used in applications above 950F (510C) where flexible graphite fails due to the effects of the oxidizing atmosphere at these elevated temperatures. Gaskets can be manufactured from standard sheet material, as filler material for spiral wound gaskets or used as facing on Cammprofile gaskets.
View Complete Details

CANFLEX SPIRAL WOUND CW

Style CW is comprised of the spiral wound sealing element only. Commonly used in tongue and groove, male-female or groove to flat flange faces.
View Complete Details

PIKOTEK ISOCORE

The Isocore insulating gasket is manufactured from neoprene coated glass-reinforced epoxy (NEMA grade G-10) in place of the failure prone conventional phenolic reinforcing material. Glass-reinforced epoxy (GRE) is many times stronger than conventional paper grade or fabrice-reinforced phenolic. The result is that the Isocore is an economical, low pressure insulating gasket that is much stronger in compression, much more resistant to stress fractures and breakage and thus, much more reliable than conventional phenolic insulating gaskets.
View Complete Details

PIKOTEK VCSF FIRESAFE ISOLATION SYSTEM

Pikotek Flange Insulation Kits are designed to work in conjunction with our insulating gaskets (Pikotek VCS, PGE and RC) to effect the complete electrical insulation of a flanged assembly. The Insulation Kits consist of one full-length insulating sleeve, two insulating washers and two steel washers for each of the bolts in the flange assembly. The purpose of the insulating sleeves is to electrically separate the bolts from each side of the flange, while the insulating washers provide electrical insulation for each of the nuts attached to the bolts. This method of insulation provides the user with a high-reliability solution to complete the electrical insulation of a flanged joint.
View Complete Details

FLOWMETER MODEL ESF

  • Pressure, Max 435 psi @ 120°F (49°C)
  • Temperature, max: POM body / PSU tube: 212°F (100°C)
Model ESF sealing liquid monitor is designed for applications where uninterrupted seal water flow is required. Adequate seal water flow for cooling and lubrication result in water savings, energy savings, reduced maintenance, and extended life of seals. The Thomson ESF single flow meter is an excellent choice for all styles of compression packing, single mechanical seals, FLUSH-GARD sealing systems for applications where gland water reduction and minimizing product dilution is essential. The sturdy modular construction and many accessories make it very flexible.
View Complete Details

THOMSON CHEM-ONE

Non-abrasive: save on shaft sleeves.
Non-asbestos: reduce handling cost.
Non-contaminating: will not degrade product.
High strength: extrusion resistant, lower wear, longer life.
High heat conductivity: lower friction, longer life.
Broad chemical compatibility: save on inventory costs, use one style for all applications.
Reduces maintenance costs.
View Complete Details

THOMSON GC-89

Non-Abrasive: long service life
General service: economize on one style
Non-contaminating: will not affect product
Non-Asbestos: save on handling cost
Reduce maintenance costs
View Complete Details

MOTION PAC X

Oversize square braid design ensures tight seal in worn or oversized stuffing boxes
CarbonAflas maximizes reliability and stability in equipment
Excellent chemical resistance: 014 pH, except strong oxidizers
Carbon filament reinforcement resists extrusion in high pressure applications
Spool stock convenience
Maintains an effective seal in a high radial run out or bent shaft conditions (e.g. Side entry AgitatorsMixers)
View Complete Details

Thomson Multipac 6101 Gasket

  • Temperature, min -100F (-75C)
  • Temperature, max: Continuous +400F Continuous +400F (+205C) Intermittent +700F (+370C)
  • Tensile Strength 2, 100 psi (ASTM 152
High tensile strength makes for a robust gasket material, which is flexible and easy to cut.
Improved formulation for higher temperature and pressure service.
Excellent mechanical properties.
Non Asbestos.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (A.R. Thomson Group)
  • Surrey, BC V3Z1A7 map, United States
  • Share us via