American Lab & Systems

• Dimensions6' x 4' x 4' (LWH)

GPMPSI: Fluid: Manufacturer: ACL HP: Shown as: N.A. NSN: Product Type: Test Stand Type: Part No: Model No: 9829-0012C Description of Equipment This unit is a portable cart used for flushing and contaminant testing of the integrated drive generator (IDG) and associated cooling system in some engines supplied on 747, and 767 airplanes. The engines involved are manufactured by Rolls Royce; the IDG's are manufactured by Sundstand. Flushing in accordance with the manufacturer's instructions reduces or eliminates generator malfunctions and failures due to contamination. The cart is a portable self-contained steel unit, supported by large diameter foam-filled swivel casters, and equipped with a floorlock and forklift channels. The cart has two louvered access doors on the front that are secured by a CalCert seal during normal use. Side and rear enclosure panels are louvered for ventilation and are attached with screws. The cart incorporates a vented tank of approximately 40 gallon capacity containing Stoddard Solvent (BMS3-2C, type 1). Supply and return hoses are attached to the top of the enclosure. Hoses are stored coiled in containers provided on the top of the enclosure. All electrical equipment on the cart meets requirements for operation in a hazardous atmosphere (NEMA class 1, group D Div. 1, Explosion proof) Electrical components require 120208 Vac, 3 phase, 60 HZ, 30A power, suitable for motor operation. A grounding cable is provided for connection to earthairplane ground. All user controls and gauges are mounted n a sloped instrument panel, which forms part of the steel enclosure. A capped male fitting for nitrogen supply is located on the left side of the enclosure. Nitrogen is used to purge solvent from the IDG and the hoses prior to disconnecting. This flushing cart provides solvent flow of 15 GPM at a regulated pressure less than 250 PSIG for flushing and contamination testing. Refer to Boeing and manufacturer specifications listed in section 7 for detailed information. Unit is mounted on pneumatic casters, with electric powered pump. Gauge: (2) 4" 0-400 PSI Temperature Gauge: -40, +120ºF Viscosity: 1.0 CTKS Filter Delta P Gauge: 0-25 PSID Flowmeter indicator: 0-25 gallon (per minute) Starter, and motor are explosion proof, electric control is manufactured by Allen Bradley. Unit includes the following: 40 gallon stainless steel reservoir with clean out ports Heat exchanger air to oil style Internal Schroeder filter External filter patch used for taking fluid samples Sampling ports Approx. Dimensions: 6' x 4' x 4' (LWH) ALS ID: GSE-104JVV Approx. Weight: Location: Units Subject To Prior Sale

• Product TypeTest Stand

GPMPSI: Fluid: Manufacturer: American Lab & Systems (ALS) HP: Shown as: N.A. NSN: Product Type: Test Stand Type: Part No: Model No: ALS No: 12678 Special Note: USED TO TEST ALLIED SIGNAL & HONEYWELL PART NUMBER 12784 DescriptionFunction of unit CDU Test Stand to test ball screw drive assemblies. The test stand will consist of a load work station with control valves, regulators, transducers, load cylinder, solenoid valves, test shield, cable harness, pressure control valves, pressure gauge, all controls and instruments will be located in the right hand front sloped panel. The CDU Test Stand will include electronic digital displays, x-y plotter, electronic control rack. The electronic rack will display torque, pressure load the main. The main fixture is included this is a manualautomatic test stand with stand alone. The finished two (2) piece system with control station and fixture in one (1) frame electronics cabinet is 19" rack style 5' ft high. The harness will be approximately 15' ft and connect the two (2) units together. A complete manual is provided with unit. Call for more information and price. Approx. Dimensions: ALS ID: TSCSD-103 Approx. Weight: Location:

• Approx. Dimensions20" W x 48" L x 24" H

GPMPSI: 6 & 10 GPM Fluid: Skydrol or Red Oil Manufacturer: American Lab & Systems (ALS) HP: Shown as: New NSN: Product Type: Mule Type: Part No: Model No: IT IS ABOUT TIME! FINALLY ... an aircraft mule that is affordable. Commuter excutive aircraft Portable Hydraulic Mule Kit Designed for DEPENDABILITY and PERFORMANCE. Assembled Typical 6 GPM Mule Kit with reservoir, pump motor starter, filters, and shut off valves. Easily stores under your work bench Kit is Pre-drilled and Pre-wired Approx. Dimensions: 20" W x 48" L x 24" H ALS ID: MUH-128 Kit Approx. Weight: Location: Units Subject To Prior Sale

• Part No12A2606-1

GPMPSI: Fluid: Manufacturer: N.A. HP: Shown as: N.A. NSN: 4920-923-1218 Product Type: Test Stand Type: Part No: 12A2606-1 Model No: Manufacturer: General DynamicsLockheed Martin Cage: 81755 Originally designed as F14 wing sweep actuator tester can be adopted for other aircraft and ball screws rotary mechanical testing. DescriptionFunction of unit Capable of testing linear and rotary actuator with 52, 000LB tension compression load. The test bed is a 16" x 8½" I beam 138½" L with a hydraulic load cylinder mounted at one end and hydraulic pump motor mounted at the other end. Test set will require a small hydraulic power supply for the ball screw motor and the load circuit. Unit is currently set up for Mil-H-5606 or equal fluid. (Skydrol on request) The control panel consists of the following; 1 Torque test gear box valve 1 52, 000 lb compression valve 1 52, 000 lb tension valve 1 Cylinder extend or retract 4 way valve 1 Actuator extend or retract 4 way valve 1 3000 PSI cylinder pressure 4" gauge 1 Overhaul test valve 1 6000 PSI pump pressure 6" gauge Fixture Assembly - Test wing sweep actuator Load Cylinder - Mfg Ortman Miller, serial number 329795, 2TH ER HYD. 6 x 34 Test bed clevis to clevis 89½" extended retract 61" Filtration - Bendix filter division rating 50 GPM, serial 3499, replacement fuse # 043589-5 Gauges - 6", 6000 PSI & 4", 3000 PSI Rotary Hydraulic power Denison Motor - Model MF05-020-31N-001, 3500 PSI, max. RPM 3000 Approx. Dimensions: ALS ID: TSL-101JVV Approx. Weight: Location:

GPMPSI: Fluid: Manufacturer: N.A. HP: Shown as: N.A. NSN: Product Type: Mule Type: Part No: Model No: Manufacturer: Industrial Measurements & Controls DescriptionFunction of unit The PDQ meter consists of two basic units: The hydraulic flow measuring unit (FMU) and the electronic readoutcontrol unit (RCU interconnected with oil resistant cables. The precision metering cylinder designed for high pressure (3000 or 5000 PSIG) operation. A special four way flow-reversing valve ensures continuous monitoring and measurement. The fluid path through the unit limits the pressure drop to a near-zero level…even at maximum rated flow. Within the FMU, flow is converted to electric signals by our special linear velocity transducer. The four valve reverse the flow path in the cylinder as the piston approaches the limit of its stroke in either direction. Operating power for the valve is provided by low pressure shop air (40-60 PSIG). Valve reversal time is approximately 0.1 second and except for this momentary interval, the valve remains in a dormant condition. The "open center" valve design ensures unrestricted flow during valve reversals. When the four way valve operates, the piston reverses, the flow signal is held at its existing level, and the velocity transducer signal polarity reverse. The signal flow is directly proportional to instantaneous volumetric flow sensed. This signal is also available in analog from at a convenient front panel connector. This makes it easy to use external instruments… oscilloscope, strip chart recorder, X-Y recorder, or power amplifiers for servo control…or even am on-line computer. High dynamic fidelity means that the flow signal can be used for transient as well as static measurement and for monitoring or feedback control of time-varying flow superimposed upon static flow. Operation Modes Automatic Model: In the "Automatic Mode" the logic circuits provide a valve reversal signal each time the piston nears the end of a stroke. Dynamic Signal Mode: Operation in the "Dynamic Signal Mode" is identical to the automatic mode except that the low pass filter in the signal circuit is reduced. Calibrate Mode: In the "Calibrate Mode" PDQ meter operation is non-cycling and the low pass filter is connected in the signal circuit. Manual Mode: The "Manual Mode" is non-cycling identical to the calibrate mode except that the low pass filter in the signal circuit is bypassed and the digital meter does not "hold" the existing reading at the end of the single stroke. The manual mode is especially useful for studying transient behavior or to observe flow response resulting from a change in the hydraulic system under test. Approx. Dimensions: ALS ID: LT-104 Approx. Weight: Location:

• Voltage:Volt 115

GPMPSI: Fluid: Manufacturer: N.A. HP: Shown as: N.A. NSN: 4935-01-217-0347 Product Type: Test Stand Type: Part No: W104067-5 Model No: DescriptionFunction of unit Volt 115 Navy use F14 aircraft Approx. Dimensions: ALS ID: TST-104 Approx. Weight: Location: Units Subject To Prior Sale