We are leaders in the market for providing best range of polyurea coatings, Boat Hull Coating, Boat Seat, Black Mamba Hose and ARO Ingersoll Rand air motors
ARMA 100 APU is a two component, polyurethanepolyurea elastomer system used for bedliners. This product provides a flexible but extremely tough monolithic membrane with excellent water and chemical resistance with a vast variety of other applications.
Keel Guards and Boat Hull Coating Boat hulls Coatings are seamless and lightweight yet extremely durable on many surfaces including aluminum, fiberglass and wood. Use our product as a keel guard or for full bottom protection to enhance the life and beauty of your boat. Exceptional abrasion and chemical resistance Withstand unimproved launch areas, hidden water hazards such as rocks, logs and branches, and a variety of beaching environments Coating sets quickly so that you can hit the water in two to three days Sound dampening features allow for a quieter ride on all water conditions Permanent adhesion means your boat bottom does not become brittle; it won’t crack, peel or chip off
Boat Seat and Raft Protection Marine and waterproof application Arma Coatings has developed a specific product, Arma 60A, which provides a rubbery yet extremely tough membrane for seat cushions, rafts and other flexible surfaces. Waterproof Chemical-resistant to salt, gasoline, oil and other damaging substances Provides “give” for comfort and tear-resistance
This heated high-pressure hose is designed and built by experts with over 20 years of experience in the polyurea coatings industry. Because the hose has a much higher pressure rating than the industry standard, it transfers heat more efficiently while maintaining excellent flexibility, durability and reliability. Specifications Nominal Interior Diameter: 38” (Main Hose) – ¼” (Whip Hose) Working Pressure: 4, 000 PSI (Main Hose) – 5, 000 PSI (Whip Hose) Min Burst Pressure: 16, 000 PSI (Main Hose) – 20, 000 PSI (Whip Hose) Max Temp: 212 F Electrical: 220V AC5 Amp – 50’ Main Hose w10’ Whip Hose Length: 50’ Main Hose Sections and 10’ Whip Hose Max of 300’
These plural component spray systems utilize ARO Ingersoll Rand air motors and pumps, specifically designed for maximum performance when applying high performance spray polyurea and polyurethane fast set coatings. Arma A2100 is a pneumatic application system and Arma H2300 is hydraulic. All pumps and gun air supplies are independently regulated for maximum performance and control of material flow with a wide variety of coating products. Control boxes are made with stainless steel. Arma A2100 (Pneumatic) Specifications 3000 PSI (210 Bars) spray pressure 240 volt, 1 or 3 phase 5060 Hertz (208 volts minimum) 12, 600 watt material heaters (including 65 ft hoses). 53 amps at 240 volt single phase. Maximum hose length: 310 ft. Compressed air required: 30 cfm at 10 lbs per minute product delivery. Warranty: Five (5) year warranty on fluid pumps and air motor. One year warranty on hoses and electronic controllers. Arma H2300 (Hydraulic) Specifications 3500 PSI spray pressure 240 volt, 1 or 3 phase 5060 Hertz (208 volts minimum) 12, 600 watt material heaters (including 65 ft hoses), 53 amps at 240 volt single phase Maximum hose length: 310 ft Warranty: Five (5) year warranty on fluid pumps and air motor. One year warranty on hoses and electronic controllers
The Probler P2 is the most operator-friendly and efficient spray gun available with a wide range of tip configurations to cover a wide range of spray and pour application needs. This dispense gun allows for easy and reduced maintenance, responsive action and application for a variety of industries. General Warranty Information 1-year warranty on all electrical components including the Black Mamba Hose 5-year factory warranty on all pump parts through Ingersoll Rand