cps energy

United States

• size
small
• Temperature ranges-67˚C to +250˚C

• frequencies10Mhz to 1GHz

LFF-9 LossyLine Flexible Filters, The “LossyLine” approach to EMI suppression is new and unique.
 The principle of the “LossyLine” approach is that unwanted
 RF energy travels through a “Lossy” medium surrounding the conductor, 
where it is absorbed and dissipated. The lossy medium is flexible
with high RF attenuation and low Q. It is ideally suited for application
as a microwave low-pass type electro-magnetic interference filter.
The usual problems inherent in conventional reactive types of 
 surrpression filters, such as mismatch, reflections, grounding, and high 
 VSWR, are eliminated. This approach has proven ideal for the elimination 
of undesired RF interference in high frequency equipment, such as radar, countermeasures, telecommunications, telemetry, etc. In most applications, lengths of only two to five inches are adequate. 
 These short lengths of flexible, small diameter, lightweight filter, are 
 very easily installed and usually require no special fittings, connectors, 
 and housings. The net result is low-cost, small size, lightweight suppression filter, effective to over 100GHz.

The “LossyLine” flexible filter can be readily installed in series or in
conjunction with existing cables or harnesses. It is available in operating
current ratings to 50 +250˚C.

• OPERATING VOLTAGE500 VDCW or 125 VACW
• OPERATING FREQUENCIES25, 60, 400, and 1,000 Hz.

The heart of a LossyLine Filter is the dissipative element. This element embodies a high temperature resisting (175˚C) epoxy resin, optimized as a magnetic lossy core, molded around the conductor, and case shielded, Hence, a true magnetic trap that absorbs rather than rejects or reflects unwanted energy. No oil is required to 
cool since there is a minimum heating effect, Practically no reactive current is present because there is little, if any, shunt capacity. LossyLine attenuates 100dB minimum, or beyond of standard instrumentation, 
 from 100 KHz up to 100 GHz and attenuation does not fall off with current. The level of RF attenuation at full load currents is maintained because of freedom from saturation. The electrical characteristics of LossyLine suppress sine waves per MIL-STD-220A, and cause the collapse of transient spikes of all kinds, particularly those with short rise times. These spikes are not reflected or transferred to other conductors, but are dissipated as heat within the lossy element (no ringing effect)

• Voltage5=50VDCW,100=100VDCW, 115=115VDCW
• SeriesLM=MINIATURES

1.OPERATING TEMPERATURE: 55˚C to + 125˚C 2.INSULATION RESISTANCE: 100 MEGOHMS MINIMUM @ 25˚C and 100 VDC AFTER 2 MINUTES. 3.HERMETICALLY SEALED
 LIFE TEST: 250 HOURS@ 1.5 TIMES WORKING VOLTAGE IR AFTER TEST: GREATER THAN 50 MEGOHMS 4.MOISTURE RESISTANCE: PER METHOD 106 OF MIL-STD-202 AFTER TEST FILTERS SHALL MEET ALL INTERNAL REQUIREMENTS. 5.TEMPERATURE CYCLING AND IMMERSION: PER METHOD 102, CONDITION D AND METHOD 104, CONDITION B OF MIL-STD-202, AFTER TEST FILTERS SHALL MEET ALL INITIAL REQUIREMENTS

• OUTSIDE DIAMETER (Inches).130
• PART NO.LST-040
• TOLERANCE on I.D.&O.D. (Inches)±.006
• INSIDE DIAMETER (Inches).040

The new EMI Suppressant Tubing provides a simple, low cost efficient means for suppressing unwanted EMI. This unique product can be slipped over standard wires and cables (insulated or uninsulated) and suppresses both conducted and radiated interference. Completely flexible and lightweight, it can be used in temperature environments from –55˚ to +250˚C without any electrical or mechanical degradation. Suppressant Tubing will provide shielding from low frequency electrostatic interference, magnetic fields and will not cause DC or low frequency AC losses. It is capable of handling RF power exceeding 10 watts CW per inch and is available either shielded or unshielded.