Our Products #373008

These units are custom-manufactured large vertical Wall Mount Air Conditioners. They range in size from 7.5 to 25-tons to provide electric heating, cooling, ventilation, and pressurization for Industrial Hazardous and Non-Hazardous Duty applications. These oversized Wall Mounts are constructed with 16-gauge galvanized steel. This style of AC is usually installed on pre-fabricated buildings prior to delivery, avoiding on-site Electrical, HVAC, and duct installation costs. Unlike roof or pad mounted air conditioners, they can usually be shipped attached to the building. Cabinets are coated with our industrial epoxy and polyurethane coating system. All coils and copper are protected with BLYGOLD PoluAl XT coil coating. Units can be controlled individually or supervised by LeadLag Controls for multiple units. Our Quality Control department conducts rigorous run-testing prior to acceptance for delivery. Typical applications include RIE Buildings, Motor Control Centers, Switchgear Buildings, Blast Buildings, Control Rooms, Offshore Drilling Rigs, and Locker Rooms. Class I, Groups BCD, Division 2 units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. OPTIONS: 50 Hertz PowerHazardous Duty Electric Heat316-Stainless Steel CabinetBuilt-in Building PressurizerAuxiliary Purge BlowerFresh Air Intake EnclosureIntake Stack (mounted or self-supported)Fire and Gas Panel Interface ContactsSystem Fault Alarms ContactsSpark Resistant Blower & Condenser Fan BladesRefrigerant Capacity ControlsLow Ambient Head Pressure ControlsChemical or Dust FiltrationIsolation Dampers for multiple unitsABS compliant constructionService Disconnect SwitchLeadLag Controls

Custom Controls Company custom manufactures vertical Wall Mount Air Conditioners suitable for operation up to 55oC131oF. Oversized variable frequency drives and motors rated for 70oC inverter duty guarantee the ability for these AC units to operate in the hottest regions on Earth. Units are fabricated in 3, 6, and 12-ton capacity to provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. All coils are protected with BLYGOLD PoluAl topcoat and 3509 primer. Units can be controlled individually or by LeadLag Controls for multiple redundancies. Typical applications include the Middle East and desert regions throughout the Earth. Class I, Groups BCD units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 units conform to IEC European Standards. Ask about our ATEX listed HACAB series High Ambient wall mount air conditioners OPTIONS: 50 HertzXP Electric Heat304 or 316 Stainless Steel CabinetPressurizerAuxiliary BlowerIntake BoxIntake Stack (mounted or self-supported)Spark Resistant Blower & CondenserRefrigerant ControlsChemical or Dust FiltrationFire DampersABS compliantService Disconnect SwitchLeadLag Controls

Energy efficient vertical Wall Mount, Heat Pump, and Step-Capacity Air Conditioners provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. Typical applications that require include Analyzer Shelters, RIE Buildings, Motor Control Centers, Blast Buildings, Switchgear Buildings, Offshore Drilling Rigs, Containers, Man Camps, Storage Facilities, etc. Units range from 1.0 to 6.0 tons. Division Two condenser section wiring is protected by liquidtight conduit. All coils are protected with BLYGOLD PoluAl XT coil coating system. Units are furnished complete with thermostats and wall grilles. Hazardous Location heater assemblies utilize low watt density stainless steel heating elements. Hazardous duty units annunciate faults with time stamp for easy troubleshooting. Units can be controlled individually or by LeadLag Controls for redundant units. No onsite refrigerant piping or exterior ductwork is required for Wall Mount installation. Class I, Groups BCD, Division 1 & 2 conversions comply with NEC 500 & 505 and NFPA Standards. (Group B, Division One Explosion Proof units require customer-furnished source of purge air). Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standard. To view Literature on this product click the link below. Ask about our CSA and ATEX listed CAB series Wall Mount air conditioners Split area classification i.e. Hazardous Duty outside General Purpose Inside50 HertzHazardous Duty Electric Heat316-Stainless Steel CabinetIndustrial Cabinet CoatingPressurizer (per NFPA 496 Standard)Auxiliary BlowerFresh Air Intake EnclosureIntake Stack (unit-mounted or self-supported)Dry Contacts to annunciate Unit FailureInterface Contacts for on-site Fire and Gas SystemSpark Resistant Blower & Condenser Fan BladeRefrigerant Capacity ControlsChemical or Dust FiltrationOpposed Blade RA Damper to control building pressureSupply Air Backdraft Dampers for multiple ducted unitsABS & A-60 compliantDisconnect SwitchRedundancy with LeadLag Controls

Roof and Pad Mount Package Air Conditioners range from 2 to 30 tons to provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. All coils are protected with BLYGOLD PoluAl topcoat and 3509 primer. Units require connecting supply and return ductwork, thru-the-roof duct sleeves, support frame or concrete pad, etc. Typical applications include RIE Buildings, Motor Control Centers, Blast Buildings, Offshore Drilling Rigs, Containers, Man Camps, Storage Facilities, etc. Class I, Groups BCD, Division 1 & 2 units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. OPTIONS: 50 HertzXP Electric Heat304 or 316 Grade Stainless Steel CabinetIndustrial Cabinet CoatingPressurizerAuxiliary BlowerFiltered Fresh Air Intake BoxIntake Stack (mounted or self-supported)Interface Contacts for Customer EquipmentSpark Resistant Blower & Condenser FansRefrigerant ControlsChemical or Dust FiltrationDampersABS & A-60 compliantDisconnect SwitchHinged Doors

CC series energy efficient closed-loop side and top-mount cabinet coolers provide cooling for Industrial Explosion Proof and Hazardous Duty Instrument Enclosures and Control Panels. Units range from 5, 000 24, 000 BTUH. Units equipped with internal condensation removal system. *Class I, Groups BCD, Division 1 & 2 conversions comply with NEC 500 & 505 Standards. (Group B, Division One Explosion Proof units require customer-furnished source of purge air.) *Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. *Unit size will increase for Division 1 and Zone 1 units. Options: 50 HertzMany models available for 380 460 VAC316-Stainless Steel CabinetIndustrial Cabinet CoatingIntegrated controls for cabinet heaters

CY Window, Heat Pump, and Thru-the-Wall Air Conditioners built specifically to provide electric heating and cooling for Industrial Hazardous Duty applications not requiring Pressurization or added Ventilation. Typical applications include Shelters, Containers, and Storage Facilities. Units range from 6, 000 to 36, 000 BTUH. All coils are protected with BLYGOLD PoluAl topcoat and 3509 primer. Class I, Groups BCD, Division 2 conversions comply with NEC 500 & 505 Standards. Class I, Groups IIAB, Zone 2 modifications conform to IEC European Standards. Click the link below to view Literature on this product. CY AND YY SERIES OF ROOM AIR CONDITIONERS AND HEAT PUMPS (Updated: 092011) Options: 50 HertzXP Electric Heat316-Stainless Steel Frame and CabinetIndustrial Cabinet CoatingSpark Resistant Blower & Condenser

RVP Roof Mount Air Conditioners provide cooling and heating for Industrial Hazardous Duty applications. Typical applications include small Drillers Cabins, Guard Shacks, Well Logging Cabins and Portable Buildings. Units range from 13, 500 15, 000 BTUH. All coils and copper are protected with our BLYGOLD PoluAl XT coating system. Up to 3.0kW electric heat can be added with auto-changeover thermostat. Class I, Groups BCD, Division 2 units comply with NEC 500 & 505 Standards. Class I, Groups IIAB, Zone 2 modifications conform to IEC European Standards. Options: Hazardous Duty Electric HeatUnit Failure ContactsSpark Resistant Blower & CondenserHazardous Duty Disconnect Switch316 Grade Stainless Steel Housing50 Hz. PowerSplit area classifications Hazardous Duty Outside General Purpose Inside for Pressurized BuildingsDivision One (Groups C and D)

Custom Controls Company custom manufactured HVAC Systems ranging from 2 100 tons for Industrial Explosion Proof and Hazardous Duty applications. Vertical or Horizontal mounting is available. Coils are protected with BLYGOLD PoluAl topcoat and 3509 primer. Structural Frame and Cabinet are available in 316-stainless steel. Typical applications include RIE Buildings, Motor Control Centers, Blast Buildings, Offshore Drilling Rigs, Containers, Man Camps, Storage Facilities, etc. Class I, Groups BCD, Division 1 & 2 systems comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 systems conform to IEC European Standards and ATEX. Options: 50 HertzXP Electric Heat316-Stainless Steel Frame and CabinetIndustrial Cabinet CoatingPressurizerAuxiliary BlowerIntake BoxIntake Stack (unit-mounted or self-supported)Alarm ContactsSpark Resistant BlowerDampersABS & A-60 compliantDisconnect Switch

Explosion Proof Unit Heaters Industry's Lowest Ignition Temperature Code Rating : T3C, 320F (160C)Dual Over temperature Protection: With both automatic and manual reset over temperature cutouts for additional safety.Nontoxic Propylene Glycol Heat Transfer FluidLow 70 PSIG Relief Valve Setting : This assures that in an emergency, the initial escaping vapor temperature remains below the 320F (160C) ignition temperature.Corrosive Resistant Options : Offered are three constructions suitable for most applications. Standard construction for use in dry non-corrosive areas includes : Welded steel heat exchanger; powder-coated cabinet; epoxy-coated motor. A 316 stainless steel construction suitable for Waste Water Treatment Plants includes : 316 stainless steel heat exchanger, headers and tubes with aluminum fins; stainless steel cabinet; corrosive resistance hardware; epoxy-coated motor. Third construction is suitable for use in Chemical Plants where chlorides are present and includes : corrosive resistance hardware; epoxy-coated motor.Explosion Proof Convectoin Heaters Designed to provide a heavy duty and corrosion resistant heat source. Features include: Wide Selection of Sizes: Four compact sizes to fit any space with ratings from 500 to 9500 watts.Sloped Top Cabinet: Prevents objects from being set on top of the convector, which can restrict airflow and cause overheating.Single and Three-Phase: Unique design provides single and balanced three-phase loads in a single element.Gas and Dust Atmospheres: Three listings cover the entire field, two for hazardous gases and vapors and one for dust particles.Wet Locations: All unit sizes available with iridite-coated elements and powder-coated frames for NEMA 3 wet locations.