Welcome to CUSTOM CONTROLS CO
Manufacturer / Exporter / Supplier Of cab, LCAB, HACAB, Pad Mount Package Air Conditioners, CC Cabinet Coolers, Window Air Conditioner, RV Style Rooftop, custom, explosion proof heaters
Manufacturer / Exporter / Supplier Of cab, LCAB, HACAB, Pad Mount Package Air Conditioners, CC Cabinet Coolers, Window Air Conditioner, RV Style Rooftop, custom, explosion proof heaters
These units are custom-manufactured large vertical Wall Mount Air Conditioners. They range in size from 7.5 to 25-tons to provide electric heating, cooling, ventilation, and pressurization for Industrial Hazardous and Non-Hazardous Duty applications. These oversized Wall Mounts are constructed with 16-gauge galvanized steel. This style of AC is usually installed on pre-fabricated buildings prior to delivery, avoiding on-site Electrical, HVAC, and duct installation costs. Unlike roof or pad mounted air conditioners, they can usually be shipped attached to the building. Cabinets are coated with our industrial epoxy and polyurethane coating system. All coils and copper are protected with BLYGOLD® PoluAl XT coil coating. Units can be controlled individually or supervised by LeadLag Controls for multiple units. Our Quality Control department conducts rigorous run-testing prior to acceptance for delivery. Typical applications include RIE Buildings, Motor Control Centers, Switchgear Buildings, Blast Buildings, Control Rooms, Offshore Drilling Rigs, and Locker Rooms. Class I, Groups BCD, Division 2 units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. OPTIONS: 50 Hertz Power Hazardous Duty Electric Heat 316-Stainless Steel Cabinet Built-in Building Pressurizer Auxiliary Purge Blower Fresh Air Intake Enclosure Intake Stack (mounted or self-supported) Fire and Gas Panel Interface Contacts System Fault Alarms Contacts Spark Resistant Blower & Condenser Fan Blades Refrigerant Capacity Controls Low Ambient Head Pressure Controls Chemical or Dust Filtration Isolation Dampers for multiple units ABS compliant construction Service Disconnect Switch LeadLag Controls
Energy efficient vertical Wall Mount, Heat Pump, and Step-Capacity Air Conditioners provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. Typical applications that require include Analyzer Shelters, RIE Buildings, Motor Control Centers, Blast Buildings, Switchgear Buildings, Offshore Drilling Rigs, Containers, Man Camps, Storage Facilities, etc. Units range from 1.0 to 6.0 tons. Division Two condenser section wiring is protected by liquidtight conduit. All coils are protected with BLYGOLD® PoluAl XT coil coating system. Units are furnished complete with thermostats and wall grilles. Hazardous Location heater assemblies utilize low watt density stainless steel heating elements. Hazardous duty units annunciate faults with time stamp for easy troubleshooting. Units can be controlled individually or by LeadLag Controls for redundant units. No onsite refrigerant piping or exterior ductwork is required for Wall Mount installation. Class I, Groups BCD, Division 1 & 2 conversions comply with NEC 500 & 505 and NFPA Standards. (Group B, Division One Explosion Proof units require customer-furnished source of purge air). Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standard. To view Literature on this product click the link below. Ask about our CSA and ATEX listed CAB series Wall Mount air conditioners Split area classification – i.e. Hazardous Duty outside General Purpose Inside 50 Hertz Hazardous Duty Electric Heat 316-Stainless Steel Cabinet Industrial Cabinet Coating Pressurizer (per NFPA 496 Standard) Auxiliary Blower Fresh Air Intake Enclosure Intake Stack (unit-mounted or self-supported) Dry Contacts to annunciate Unit Failure Interface Contacts for on-site Fire and Gas System Spark Resistant Blower & Condenser Fan Blade Refrigerant Capacity Controls Chemical or Dust Filtration Opposed Blade RA Damper to control building pressure Supply Air Backdraft Dampers for multiple ducted units ABS & A-60 compliant Disconnect Switch Redundancy with LeadLag Controls
Custom Controls Company custom manufactures vertical Wall Mount Air Conditioners suitable for operation up to 55oC131oF. Oversized variable frequency drives and motors rated for 70oC inverter duty guarantee the ability for these AC units to operate in the hottest regions on Earth. Units are fabricated in 3, 6, and 12-ton capacity to provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. All coils are protected with BLYGOLD® PoluAl topcoat and 3509 primer. Units can be controlled individually or by LeadLag Controls for multiple redundancies. Typical applications include the Middle East and desert regions throughout the Earth. Class I, Groups BCD units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 units conform to IEC European Standards. Ask about our ATEX listed HACAB series High Ambient wall mount air conditioners OPTIONS: 50 Hertz XP Electric Heat 304 or 316 Stainless Steel Cabinet Pressurizer Auxiliary Blower Intake Box Intake Stack (mounted or self-supported) Spark Resistant Blower & Condenser Refrigerant Controls Chemical or Dust Filtration Fire Dampers ABS compliant Service Disconnect Switch LeadLag Controls
CC series energy efficient closed-loop side and top-mount cabinet coolers provide cooling for Industrial Explosion Proof and Hazardous Duty Instrument Enclosures and Control Panels. Units range from 5, 000 – 24, 000 BTUH. Units equipped with internal condensation removal system. *Class I, Groups BCD, Division 1 & 2 conversions comply with NEC 500 & 505 Standards. (Group B, Division One Explosion Proof units require customer-furnished source of purge air.) *Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. *Unit size will increase for Division 1 and Zone 1 units. Options: 50 Hertz Many models available for 380 460 VAC 316-Stainless Steel Cabinet Industrial Cabinet Coating Integrated controls for cabinet heaters
Roof and Pad Mount Package Air Conditioners range from 2 to 30 tons to provide electric heating, cooling, ventilation, and pressurization for Industrial Explosion Proof and Hazardous Duty applications. All coils are protected with BLYGOLD® PoluAl topcoat and 3509 primer. Units require connecting supply and return ductwork, thru-the-roof duct sleeves, support frame or concrete pad, etc. Typical applications include RIE Buildings, Motor Control Centers, Blast Buildings, Offshore Drilling Rigs, Containers, Man Camps, Storage Facilities, etc. Class I, Groups BCD, Division 1 & 2 units comply with NEC 500 & 505 and NFPA Standards. Class I, Groups IIAB, Zone 1 & 2 modifications conform to IEC European Standards. OPTIONS: 50 Hertz XP Electric Heat 304 or 316 Grade Stainless Steel Cabinet Industrial Cabinet Coating Pressurizer Auxiliary Blower Filtered Fresh Air Intake Box Intake Stack (mounted or self-supported) Interface Contacts for Customer Equipment Spark Resistant Blower & Condenser Fans Refrigerant Controls Chemical or Dust Filtration Dampers ABS & A-60 compliant Disconnect Switch Hinged Doors
RVP – Roof Mount Air Conditioners provide cooling and heating for Industrial Hazardous Duty applications. Typical applications include small Drillers Cabins, Guard Shacks, Well Logging Cabins and Portable Buildings. Units range from 13, 500 – 15, 000 BTUH. All coils and copper are protected with our BLYGOLD® PoluAl XT coating system. Up to 3.0kW electric heat can be added with auto-changeover thermostat. Class I, Groups BCD, Division 2 units comply with NEC 500 & 505 Standards. Class I, Groups IIAB, Zone 2 modifications conform to IEC European Standards. Options: Hazardous Duty Electric Heat Unit Failure Contacts Spark Resistant Blower & Condenser Hazardous Duty Disconnect Switch 316 Grade Stainless Steel Housing 50 Hz. Power Split area classifications – Hazardous Duty Outside General Purpose Inside for Pressurized Buildings Division One (Groups C and D)
Share your thoughts with other customers for CUSTOM CONTROLS CO
Add Review