Post Buy Requirement
EP
United States
Add Review

Our Products

RFK Installation Tool

RETROFIT KIT (RFK) INSTALLATION TOOL
The RFK Series Installation Kit includes two (2) labor and time saving magnetic suspension devices used to expedite installation of the gear tray. Supports one man installation, even when installing 8-foot fixtures.


The round magnetic end of the tool is attached to the outer ends of the strip fixture housing. The arrowed end of the tool is inserted through the slotted holes on each end of the retrofit gear tray, then rotated 90 degrees to hold the gear tray in place while the contractor completes termination of the supply wires to the gear tray.


100% reusable for multiple installation projects, the tool eliminates the use of string, tie wire, nylon straps, or other temporary suspension methods.
View Complete Details

LED RetroFit Conversion Kits For LED Strip

  • Input Voltage 120-277 VAC 120-277 VAC
  • Input Frequency 50 - 60 Hz 50 - 60 Hz
  • Power Factor > 0.9 @ Full Load; 120 through 277V
  • Inrush Current 20 Amps @ 230 Volts
LED RETROFIT CONVERSION KITS FOR LED STRIP
Engineered Products Companys LED RetroFit Conversion Kits convert older 4-foot and 8-foot T8 or T12 strip-type luminaires into energy efficient LED luminaires. This is a low-cost efficient and effective replacement upgrade solution that delivers high performance high lumen output at a fraction of the cost compared to the purchase and installation of a new LED luminaire.

Upgrading the existing strip-type housing to a new LED luminaire is a simple and straightforward installation that improves the overall integrity, quality and sustainability of the lighting system as an energy management solution to reduce the buildings energy consumption.

EPCOs LED RetroFit Conversion Kits is available in 16 configurations.

BENEFITS

ETL Listed to UL 1598C.
DLC Listed and approved (standard wattage driver only).
Reduced energy consumption compared to linear fluorescent lighting systems.
High system efficacy.
100% Tested and certified before shipping ensures out of the box performance.
Assembled in the United States.
Five (5) Year Warranty, 50, 000 hours, minimum at L70.
Minimal part numbers. Other companies require separate numbers for various "strip-type" fixture housing widths.
FEATURES

One-piece construction, compact design, trouble free installation.
Integral "adjustable" installation brackets accommodate 4.25" (107.95mm) or 5.0" (127mm) "strip-type" fixture housing widths.
Multi-Voltage Operation - 120277V input.
Pre-wired at the factory for 0-10V dimming.
Available in 4000K and 5000K color temperatures.
Color Rendering Index (CRI): 80+
Kits are available with or without frosted diffuser to meet your application needs.
View Complete Details

LED RetroFit Kit Diffuser

LED RETROFIT KIT FROSTED DIFFUSER
The one-piece, snap-on polycarbonate UV stabilized frosted diffuser features 2.25 (57.15 mm) high contoured shape design that provides even lumen distribution without glare, shadows, or hot spots. Includes two (2) end caps with screws.

The edges of the diffuser in conjunction with the end caps assure a solid attachment to luminaires housing with minimal light leakage.
The diffuser is easily removable for maintenance or cleaning.
View Complete Details

Deluxe CordLights

EPCO Deluxe CordLights
Deluxe CordLights are intended for severe environments and are impervious to dust, dirt, chemical vapors, salt spray and other corrosive elements. Constructed of heavy-duty 142, 143 or 123 SJTW round cord with a 75C (167F) temperature rating, Deluxe Cord Lights are UL Listed and complies with UL Standard 1088 for Temporary Lighting Strings.

UL Listed. File #E190858. Meets all OSHA Standards.
U.L. 1088 - Article 17.2 - lamp guard shall be constructed of polymeric material. The actual molded product is polypropylene. Flame class is V-0 meets U.L. 746C.
Meets the requirements of the 2014 National Electrical Code: Article 590.4(F).
Suitable for indoor and outdoor use.
Weather resistant lamp sockets feature rigid-mounted eyelets for hooks or wire to simplify hanging.
Unique open and secure closure clasp on the heavy duty bulb cage easily facilitates bulb changes.
A patented detent snap-off, snap-on fitting on the lamp socket enables quick replacement if the Safety Cage becomes damaged.
Rated only for use with Type A23 Incandescent Lamp - 150-watt rating (maximum), Compact Fluorescent or LED Lamps.
U.S. Patent No.: D.439, 697.
View Complete Details

T5 RetroFit Conversion Kits

T5 RETROFIT CONVERSION KITS
Engineered Products Company's (EPCO) T5 RetroFit Conversion Kits converts older 4-foot and 8-foot T8 or T12 strip-type luminaires into energy efficient T5 luminaires. Each kit includes T5 Bi-Pin Lamp Sockets, T5 Retrofit Bracket Socket Plates and Self-Tapping Screws.

Complies with UL Standard 1598B and 1598C.
Pre-wired conversion kit bracket; Installer only needs to complete ballast lead terminations to finish conversion kit bracket installation.
Pre-painted with smooth, glossy, highly reflective white paint.
Includes holes for installing Ballast Cover or Reflectors.
FEATURES AND BENEFITS

Easily retrofits existing T8 or T12 fluorescent luminaires to energy efficient and high lumen output T5 luminaires.
Suitable for use with all manufacturers' T5 lamps.
Lowers maintenance costs due to less frequent T8 or T12 lamp replacement.
The combination of EPCO's low cost RetroFit Conversion Kit, electronic ballasts, and T5 fluorescent lamps are recognized as the most energy efficient lighting system today.
EPCO's RetroFit Conversion Kits are made in the USA, complies with the American Recovery and Reinvestment Act (ARRA), and allows Contractors to readily participate in Government sponsored lighting retrofit projects.
PNs: 14060, 14065, 14066, and 14067 may be suitable for use with Linear LED Retrofit Lighting. These designated RetroFit Conversion Kit part numbers fitted with "non-shunted" lamp holders are suitable for use with linear LED engines (T5 shaped LED tubes) as long as the LED engine is classified per UL 1598C.
View Complete Details

TIGER And TIGERcub HITypeLamps Lighting Accessories

UL Listed.
Suitable for use in damp locations.
Meets the requirements of the 2014 National Electrical Code: Articles 410.62(C)(1) and (2), 410.104(A), 410.122, 410.130(F)(5) and 590.4(F).
A cost effective solution to incandescent string lighting.
Energy savings: 15% to 25% less than ten (10) 100-watt Incandescent Lamps.
Lumen output: 52% more effective than ten (10) 100-watt Incandescent Lamps.
Minimal relamping! Average rated lamp life for a Type-O Metal Halide Lamp is 10, 000+ hours compared to 1, 000 hours for a standard 100-watt Incandescent Lamp.
View Complete Details

Insulation Piercing Lamp Socket

Suitable for indoor or outdoor use.
Use to repair Contractor Grade CordLights, signage, appliances or other lighting fixtures.
Integrally designed terminals and contacts provide a superior electrical connection.
Use with 12 or 14 AWG THHN insulated stranded wire.
No cutting, wire stripping, wire nuts or soldering required.
Rated only for use with Type A23 incandescent lamp - 150-watt rating (maximum), compact fluorescent or LED lamps.
View Complete Details

TIGER 400 HID Temporary Light

  • TIGER 400 HID 4, 000K 38, 000
TIGER 400 HID Temporary Light
UL Listed.
Suitable for use in damp locations.
Meets the requirements of the 2014 National Electrical Code: Articles 410.62(C)(1) and (2), 410.104(A), 410.122, 410.130(F)(5) and 590.4(F).
Compact size, lightweight, and balanced construction. Easy to carry and install.
A cost effective solution to incandescent string lighting:
Energy savings: 15% to 25% less than ten (10) 100-watt Incandescent Lamps.
Lumen output: 52% more effective than ten (10) 100-watt Incandescent Lamps.
Pre-wired for 120V operation. CWA Multi-tap Ballast can be easily re-configured for 208V, 240V or 277V applications.
Minimal relamping! Average rated lamp life for a Type-O Metal Halide Lamp is 10, 000+ hours compared to 1, 000 hours for a standard 100-watt Incandescent Lamp.
TIGER 400 HID Temporary Light Fixtures include:

HID Light Fixture.
Type-O Metal Halide Lamp.
Chrome plated heavy-duty 11 AWG welded steel Safety Cage.
3-Foot 183 SJTW power cord with 15 AMP plug.
View Complete Details

Plastic Safety Cage

Suitable for indoor or outdoor use.
Unique open and secure closure clasp on the heavy-duty Safety Cage easily facilitates bulb changes.
View Complete Details

TIGRESS 105-Watt Compact Fluorescent Lamp

The 105-Watt Compact Fluorescent Lamp is included with each TIGRESS Temporary Light Fixture. This self-ballasted lamp provides a productive work environment during building construction or major renovation, consumes less than one-half of the total energy costs compared to metal-halide lamps, and is approximately 3 to 5 times more efficient than standard incandescent lamps and can last up to 10 times longer.

CFL lamp will not decay significantly when compared to metal halide lamps.
Long lamp life.
ETL Listed.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Engineered Products Co.)
  • Minnetonka, MN 55343 map, United States
  • Share us via