Our Products

The TD-1580 and TD-1581 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support an EIA-530 serial link. However due to the transparency and flexibility of the design, the TD-158081 can be used as 6x4 independent 6 Mbps RS-422 channels and 2x1 independent 256 Kbps RS-232 channels (see below for details). This incredible versatility can solve a myriad of serial data communications problems. Your once limited serial links can not only be consolidated but extended to over 20 Km on a single fiber pair. SCADA (supervisory control and data acquisition), Telecommunications, Facility Automation and Control, even DMX Lighting control applications can all benefit from the TD-158081. For more advanced systems, a Regeneration switch on the TD-1581 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT).

The MD-3 units are accessories for the LightViper Series 32 product line and are not stand alone products. They need to be connected to an existing LightViper Series 32 system to function. The MD-3 is used in pairs and will function utilizing the Control EtherCon connector on Series 32 models including VIS-1832, VIM-1832, VIS-4832, VIM-1808 & VIM-0808. The MD-3 translates RS422RS232 or MIDI control information into TTL data. This data is then transported along with the audio input data (returns) from the FOH position to the Stage.

The SFP-BA10XC-0000-M is a medium reach electrical transceiver module designed to transmit and receive MADI signals up to 125 Mbps over 75 coaxial cables via HD-BNC connectors. The cable driver amplitude and edge rate are automatically configured in order to achieve compliance to AES10-2003.

These MADI modules are also available as dual transmit and dual receive modules for use in the FOI-6012. These dual units are non-MSA compliant and would not be compatible with the WDM16.

The FOI-1GBT provides complete electrical isolation for 1000BASE-T Gigabit Ethernet communications. The unit has an automatic MDIMDIX switch over capability that allow users to use either a straight or crossover cable for all LAN configurations. The copper interface is fully automatic. If TP+ and TP- are reversed, the unit will automatically swap the polarity internally. Similarly, if the transmit and receive pairs are reversed, the unit will automatically swap both pairs internally. Therefore, either a crossover or straight cable can be used.

The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional 1000BASE-T Cat5e cabling is limited to a maximum distance of 100m, but multimode optics on the unit can extend the distance to 550m, while singlemode optics can further extend the distance to 5km.A typical link consists of two FOI-1GBT, one at each end of the network, with a duplex fiber optic cable between them.

The FIS-6510 fiber receiver and FIS-6511 fiber transmitter provide a high performance, high reliability, transparent cross-site connection between RF communications equipment. They are ideal for L-Band, low frequency radio and distribution of wireless standards such as cellular, GPS, Wi-Fi and WiMAX. The ultra-wide dynamic range results in negligible degradation of signals due to noise or inter-modulation effects. Independent of data format, the 65106511 are suitable for most analog or digital signal modulation including FM and QPSK. The RF connects via a 50 SMA connector. Units are available with Singlemode LC PC, and ST fiber connections (other custom options available, contact your FiberPlex representative). The FIS-6510 and FIS-6511 are in the FiberPlex standard FOI enclosure. The FOI packaging is the field proven standard for mission critical and military applications. The solid steel enclosure is not only rugged, but provides a seal to minimize EMI and RFI emissions and penetration. The FOI versions can be housed and powered in a standard FiberPlex RMC enclosure or powered standalone using a FiberPlex PSQ-4909 AC or PSQ-4920 DC power supply.

The FOI-5401and TD-5401 provide complete electrical isolation for T1, DS1 or E1 communications.

The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. FiberPlex recommends R units for high security applications because the units have added filtering and shielding for RFI suppression.

In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional T1 cabling is limited to a maximum distance of 6200ft (1.89km), but multimode optics on the unit can extend the distance to 2km, while singlemode optics can further extend the distance to 20km. A typical link consists of two FOI-5401, one at each end of the network, with a duplex fiber optic cable between them.

A complete bundled package for Fire Alarm annuciation applications. Includes warning strobe.

The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Multimode optics on the units can extend the distance to 2km.

The TD-1280 and TD-1281 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support a TIA-232 serial link. However due to the transparency and flexibility of the design, the TD-128081 can be used as 3x2 independent 1 Mbps TIA-232 channels and 5x5 independent 120 Kbps TIA-232 channels.
This incredible versatility can solve a myriad of serial data communications problems. Your once limited serial links can not only be consolidated but extended to over 20 Km on a single fiber pair. SCADA (supervisory control and data acquisition), Telecommunications, Facility Automation and Control can all benefit from the TD-128081.

For more advanced systems, a Regeneration switch on the TD-1281 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT).

Even though we deal with rocket scientists, this is NOT rocket science. So we are making it as simple as possible. One SKU gets you everything you need to improve your system from copper to fiber. Just pick your system

The FiberPlex Technologies TKIT bundles takes the incredible flexibility of our TD-6010 12.5 Gbps workbox and bundles it with a set of application specific SFP modules to create a simple, easy to order solution for your specific application.

The ADP-2981 ADP-2982 is a stand-alone wall or shelf mountable loudspeaker unit. Each unit houses and powers an 8-inch speaker and, in the case of the ADP-2981, a high-intensity strobe.

The unit utilizes FiberPlex FOI series modules to extend Public Address and Mass Notification systems via fiber. External audio signals such as voice announcements, music, a doorbell buzz, etc. are first connected to a FOI-2981 or FOI-2983. This FOI unit then transmits the signal via a fiber optic link to a FOI-4982, conveniently housed and powered by an ADP unit. From there the FOI-4982 drives up to 10 ADP units in a daisy chain.

Each ADP unit is equipped with an AC line-powered supply to drive the amplifier and supply DC power to an attached FOI module.

The ADP-2981 also contains a strobe annunciator, useful for areas with high background noise or those with hearing difficulties. A knob on top of the unit controls the volume threshold that the audio must exceed for the strobe to flash.

The FIS-6510 fiber receiver and FIS-6511 fiber transmitter provide a high performance, high reliability, transparent cross-site connection between RF communications equipment. They are ideal for L-Band, low frequency radio and distribution of wireless standards such as cellular, GPS, Wi-Fi and WiMAX. The ultra-wide dynamic range results in negligible degradation of signals due to noise or inter-modulation effects. Independent of data format, the 65106511 are suitable for most analog or digital signal modulation including FM and QPSK. The RF connects via a 50 SMA connector. Units are available with Singlemode LC PC, and ST fiber connections (other custom options available, contact your FiberPlex representative). The FIS-6510 and FIS-6511 are in the FiberPlex standard FOI enclosure. The FOI packaging is the field proven standard for mission critical and military applications. The solid steel enclosure is not only rugged, but provides a seal to minimize EMI and RFI emissions and penetration. The FOI versions can be housed and powered in a standard FiberPlex RMC enclosure or powered standalone using a FiberPlex PSQ-4909 AC or PSQ-4920 DC power supply.