Other Products / Services

Machine Manufacturer: Caterpillar
Machine Model: IT28B
Machine #: 3657
Machine Serial Number: 1JK00467
Stock Number: 183836

Type of Boom (Standard, Hi-Lift, IT, etc.): IT (Integrated Toolcarrier)

Boom Notes
Condition of Pin Holes: All of the pin holes are in good shape and are holding bushings.

Condition of Surfaces Around Pin Holes: The surfaces surrounding both of the lower coupler pin holes, have a little wear into them.

Condition of Boom Arms: The RH boom arm appears to be bent inward a bit, from the cross tube to the coupler pin hole.

RepairsModifications: None.

CracksDamage: See boom arm above.

Attachment Evaluation
Dozer Blade Evaluation

Machine Manufacturer: CATERPILLAR
Machine Model: D5H
Machine #:3862
Machine Serial Number: 8RJ-05190
Stock Number: 183613

Blade Information
Type of Blade (Straight, Semi-U, Full-U, Angling, etc): SEMI-U
Blade Width: 128"
Blade Height: 48"
Blade Manufacturer: UNKNOWN

Blade Notes
Condition of Pin HolesTrunnion Ball Sockets: GOOD (COULD USE A LIGHT SAND)
Condition of Moldboard (note the amount of wear back towards all cutting edge & corner bit
bolt holes): GOOD - LIGHT WEAR
Condition of Cutting EdgesCorner Bits: GOOD - LIGHT WEAR
Condition of Blade ArmsAngling FrameStruts: GOOD
Condition of any Hydraulic Cylinders (Tilt, Angling, etc.): ONE CYLINDER HAS BAD CHROME
RepairsModifications: NONE
CracksDamage: NONE

Attachment Evaluation
Excavator Boom

Machine Manufacturer: Caterpillar
Machine Model: 330C MH
Machine #: 4000
Machine Serial Number: D3C00310
Stock Number: 191513

Boom Information
Working Length of Boom: 30ft., 2 inches
Type of Boom (Standard, Material Handler, Mass, etc): Material Handler

Boom Notes
Condition of Pin Holes: All of the pin holes appear to be in good shape and are holding bushings.

Condition of Surfaces Around Pin Holes: All of the surfaces appear to be in good condition.

RepairsModifications: None found.

CracksDamage: None found.

Other (Tag Info, etc.): The info on the attached tag is as follows:

The lower pin hole bushings for the bucket pins, may need to be replaced. The
pin boss surfaces fior the bucket pin holes, have some wear, especially on the
inner surfaces (see photos). All of the other pin holes appear to be in decent
shape and no cracks have been found.

Attachment Evaluation
Dozer Blade Evaluation

Machine Manufacturer: Caterpillar
Machine Model: D6R LGP
Machine #: 3523
Machine Serial Number: 9PN01775
Stock Number: 155828

Blade Information
Type of Blade (Straight, Semi-U, Full-U, Angling, etc): Straight Blade
Blade Width: 12 ft. (Approx.)
Blade Height: 3 ft. High to the top of the moldboard. 5 ft. High to the top of the debris guard.
Blade Manufacturer:

Blade Notes
Condition of Pin HolesTrunnion Ball Sockets: The pin holes for the LH upper strut have some wear. All of the "Ball Trunnions" and sockets appear to be in decent shape.

Condition of Moldboard (note the amount of wear back towards all cutting edge & corner bit
bolt holes): There are some dents in the moldboard face and there is a hole and a few cracks on the RH side of the face. Both lower front side edges are cracked as well. The bottom of the moldboard appears to be in decent shape. A debris guard has been added to this blade at some point and it is bent rearward on the LH side.

Condition of Cutting EdgesCorner Bits: The cutting edges appear to be in decent shape and the corner bits have a bit of wear.

Condition of Blade ArmsAngling FrameStruts: The blade arms look to be in decent condition.

Condition of any Hydraulic Cylinders (Tilt, Angling, etc.): The working condition of the blade tilt cylinder is unknown.

RepairsModifications: Debris guard added to the top of the blade.

CracksDamage: As mentioned above concerning damagecracks on the moldboard.

UNDERNEATH SIDE OF BOOM HAS BEEN PLATED OVER A MAJOR CRACK

WORKING LINK = 255 12" WITH 4" PIN HOLES
ALL PIN HOLES ARE IN GOOD COND.
SEE PICS.

SHIPPING- 22' LONG , 3' WIDE , 6' HIGH.