Our Products #4841141

Upgrade for use with Grade 7 Transport Chain
Utilize standard Crosby A-323 Alloy Eye Grab Hooks
New design "one piece" forge handle
Continuous take-up feature, infinite adjustment, gets the last half of chain
One piece assembly, no bolts or nuts to loosen
Ratchet spring rust-proofed
All load bearings or holding parts forged
Easy-operating positive ratchet

The tensioners that are hidden inside the post.

Easy to install
Slide the Invisiware receiver into a pre-drilled hole in the end post. The inside of the receiver is female -threaded to accept the male-threaded swaging stud (below) that is attached to the cable. The head of the receiver is broached for an Allen wrench. To tension the cable, simply insert the Allen wrench and rotate the receiver around the male threads to draw the stud and cable further inside the receiver. When installed, only the head of the Invisiware receiver is exposed on the outside of the Post.

Use with metal or wood on level runs or stairs
Invisiware receivers are used with pipe and with round, Square or rectangular metal tubing. Pipe ends are counterbored, so the Full perimeter of the head rests on a flat surface in the pipe. The head rests on the outside wall of a flat-sided metal post. A plastic washer is included and acts as a scratch resistant barrier between the head of the receiver and the metal post.

For use in wood, the Invisiware receiver can rest against the outside of the post or the post can be counterbored with the receiver recessed in the post. For wood applications also order 716 SAE Stainless steel Washer

The Twin-Path Adjustable Bridle is the ultimate multiple use rigging tool. It can be used in applications where a standard two-leg or four leg bridle is used with the added advantage of self-adjustment to awkward loads. The Twin-Path Adjustable Bridle self-adjusts over the center of gravity to find the lifting point. The Twin-Path Adjustable Bridle can also be used as a complete rigging tool for choker, vertical, or basket hitches. The use of two or more Twin-Path Adjustable Bridles facilitates lifts with multiple lifting points.

30' DuraTech Self-extracting features heavy duty 316" galvanized steel cable, rugged cast and CNC machined aluminum housing and internal drum, hard-wearing bronze ratchet center and pawls, alloy steel main shaft, and our DuoTech load-indicating snaphook for attachment to the dorsal D-ring of a full-body harness. This Self-extracting is fully serviceable. Meets or exceeds all OSHA requirements.

6' shock absorbing lanyard features 1 38" tubular web with integral shock absorber and 2 regular snaphooks. Meets or exceeds all applicable OSHA requirements. Meets or exceeds ANSI A10.14 andor Z359

Technical References
Webbing: ANSI Z359 3.2.2.2 - 3.2.2.7
Shock Abs.: ANSI Z359 2.23, 3.2.4
Snap Hooks: ANSI Z359 2.63, 2.63.1, 3.2.1

All steel high strength type for overhead cranes. This rope is compacted to enhance abrasion characteristic and to reduce sheave- and drum wear. Up to 40% strength increase over standard 6-strand constructions.

High strength rope type. Type 'V' is extra compacted.
Core is parallel laid to minimize strand nicking. Up to 40% strength increase over standard 6- strand constructions. Requires corresponding drum groove direction. OEM rope on some DEMAG cranes. The Python Power-9 construction provides an increase in contact points between rope and sheave. Less wear on the rope and of your equipment.

Python Power-9 is NOT rotation resistant or non-rotating

Easy and safe to use! Just lift the load, set the Rollers, and move The recirculating chains on the Hillman Rollers provide controllable heavy moving right on ordinary flooring. Fully directional swivel tops allow equipment positioning in the tightest quarters. 3 and 8 ton Kits and Sets feature swivel padded rollers. 15 ton and higher Kits and Sets are available with your choice of swivel-locking padded rollers or rollers with swivellocking diamond steel grid tops and loose Preload Pads.

Shackles Quenched and Tempered and can meet DNV impact requirements of 42 joules at -20 degrees Celsius
Working Load Limit permanently shown on every shackle
Forged-Quenched and Tempered with alloy pins
Capacities 13 thru 55 metric tons
Look for the Red Pin the mark of genuine Crosby quality
Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds or other certification. Charges for proof testing and certification available when requested at the time of order
Hot Dip Galvanized or Self-Colored
Fatigue rated
Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271D Type IVA, Grade A, Class 2, except for those provisions required of the contractor.

ComforTech 3-D-ring Full Body Harness is configured for fall arrest and work positioning. It includes a shoulder yoke, twin butt pads and waist pad positioning assembly. The waist pad positioning assembly has integral side D's and removable work belt. Features Quick-Connect leg straps to ease donning.

The mounting end on each of our Adjust-A-Body tensioners has a male thread that mates with the female thread within the body of the tensioner. The swaging ferrule is swaged onto the cable and holds the cable inside the body. The body rotates on the cable and provides a considerable amount of take-up during tensioning with an open-end wrench. After tensioning, the lock nut locks the assembly in place.

Easy and safe to use! Just lift the load, set the Rollers, and move The recirculating chains on the Hillman Rollers provide controllable heavy moving right on ordinary flooring. Fully directional swivel tops allow equipment positioning in the tightest quarters. 3 and 8 ton Kits and Sets feature swivel padded rollers. 15 ton and higher Kits and Sets are available with your choice of swivel-locking padded rollers or rollers with swivellocking diamond steel grid tops and loose Preload Pads.