Post Buy Requirement
HS
United States
Add Review

Other Products / Services

Mist Air Purifier

  • Series MAP
Our Mist Air Purifier is designed to filter fines from extruders, preconditioners and coaters. Using water injection nozzles, the fines are captured and transported to the waste drain. The capturing of these fines can help reduce contamination sites for bacterial growth and reduce downtime for routine equipment cleaning.

STANDARD CONSTRUCTION FEATURES

304 Stainless steel product contact surfaces
Interior product contact welds continuous and ground flush to 120 grit
Exterior welds continuous
3 HP, 304 stainless steel, washdown duty motor, Rated for 185 degrees F
Belt drive arrangement with 304 stainless steel guard
304 Stainless steel foot pedestal
500 CFM airflow
Water consumption 2 G.P.M.
Integral 4 mesh filter media
34 Fines and condensate drain
Internal baffle and drain
Safety grid on back opening in rear plate
Splash baffle with drain pan for external filter
Water addition nozzle
18 Stainless steel
0.7 GPM at 20 PSI
Must be installed in convey line near pre-conditioner vent
Support legs, 304 stainless steel, for floor mounting of the unit complete with leveling feet, 12 max clearance
View Complete Details

SideWinder Filter Receiver

  • Series SWR
The SideWinder filterreceiver features an easy open clean air plenum for side access to the top removal style, self-supporting filter cartridges.

OPTIONAL FEATURES

Available in carbon steel, stainless steel or aluminum construction
High entry inlet with baffles to protect bags from direct contact by the product
NEMA 4X or NEMA 79 timer enclosure
Support legs
Maintenance access ladder and platform
InspectionAccess opening
IndustrialFood grade epoxy interior
Smooth not Flush (80 grit) or Smooth and Flush (120 grit) weld seams
70 Degree hopper slope
Explosion relief vent
Flanged product inletclean air outlet
Pulse on demand differential pressure gauge andor switch
View Complete Details

Dense Phase Transporter

  • Series DPT
This is a pressure vessel that utilizes compressed air to convey products in dense phase.

Standard Construction Features

60 degree cone bottom
Short radius 90 degree elbow product discharge connection
Inlet with butterfly valve NEMA 4 enclosure
Vent connection with butterfly valve NEMA 4 enclosure
Compressed air inlet connection
Inspection portmanway
Exhaust port with manual ball valve
Coupling for high level indicator
Pressure switch - NEMA 4 enclosure
Liquid filled conveying pressure gauge
Support legs
Air Control Assembly complete with the following:
Air filter
Convey pressure regulator
Pilot operated pressure regulator
Flange mounted venturi nozzle
OnOff control butterfly valve - NEMA 4 enclosure
Three (3) Manual shut off valves with barbed hose connections
Galvanized pipe fittings and support stand

OPTIONAL FEATURES

Available in carbon steel or stainless steel construction
NEMA 79 electrical enclosures
Line boosters
IndustrialFood grade epoxy interior
Smooth not Flush (80 grit) interior
Smooth and Flush (120 grit) interior
70 Degree hopper slope
Air accumulator
View Complete Details

KleenLift - Extruder Hood

  • Series KLU
The extruder hood is the pick-up point of a negative air lift system. It utilizes purified air to the convey the product from the extruder to a receiver that typically feeds a dryer.

STANDARD FEATURES

Laminar air distribution eliminates clumping and tumbling and optimizes velocity at the die area.
Custom engineered interface between the hood, extruder barrel and knife drive.
Air bypass system delivers airtight shutoff when diverted, easier service and wear reduction of blade seal.
Sanitary design throughout the hood minimizes opportunity for product build up and hot spots and includes:
Treated air supply options with HEPA filtration to eliminate finish product contamination.
Sanitary access door, on clean side main shell, for easy cleaning.
Designed for heat treatment or burnout temperatures up to 300 degrees F.
FESTO Clean Design Solenoid Block for safe washdown and easy accessibility.
Actuated lower clamshells to eliminate product build up during rejectbypass.
Added safety features such as:
Rod lock cylinders on main clamshells to lock main shells in place for operator safety and positive control
NEMA 4X electrical enclosure separates electrical and pneumatic connections.
Pressure transducer for die chamber pressure verification and trending.
Profected gasket design to provide superior overall fit up and easy replacement in the field.
Large viewing windows for visual inspection of cutter and die while in operation.
CE Compatible


Options:

Pressure fan for positive pressure at the die
HEPA Filtration
Steam or Gas Heated Air Supply
Ozone
View Complete Details

ReelKLeen

The HorizonPSI ReelKleen system is an innovative way to ensure the proper sanitation of your supply line. The compact device applies a low volume spray of sanitizing agent to the interior of your cleaned conveying line. It minimizes the use of sanitizing solution, equipment and labor needed to keep your line safe.

Any low viscosity pump-able solution
ACSPhresh (Acidified Calcium Sulfate)
Quaternary (Quat) Sanitizing Agent
Alcohol based solutions (possible safety hazards from vapors)
Other agents that are customer recognizedapproved

STANDARD FEATURES

Compressed air
Spray valve
Mix valve
Mix tank
Reel motor
Speed control
Diaphragm pump
Drain valve
Reel motor foot switch
120 volt powered hose reel
View Complete Details

Replaceable Back Elbow

The economical feature of this elbow is in the convenience of replacing the outer radius back, where the most wear occurs, without replacing the entire elbow. This type of elbow is also more economical than a tube bend elbow when the size of the tube or pipe exceeds 10"" diameter. The elbows are constructed of 12 gauge carbon steel with a 10 gauge abrasion resistant removable back.

They are available in carbon steel or stainless steel construction.
View Complete Details

Clear Air Exhaust Fans

  • Series HS
The clean air exhaust fan is connected to the vent filter plenum to aid in evacuation of air from the vent filter.

STANDARD CONSTRUCTION FEATURES

Split housing for maintenance ease
Even O.D. pipe sizes on inlet and outlet
Non-Sparking cast aluminum wheel and housing
Assortment of wheel sizes to pinpoint your performance requirements
Reliability
Wheels both statically and dynamically balanced
Rustproof

OPTIONAL FEATURES

Carbon steel or stainless steel construction
InletOutlet damper
Discharge silencer
X-Proof motor enclosure
Belt driven versus standard direct driven
View Complete Details

CBA Bin Activator

This bin emits vibrations in hoppers in order to "shake" the product and break up lumps or stoppages in storage silos.

STANDARD CONSTRUCTION FEATURES

45 Degree or unique 3060 degree cone design
Weld-On adaptor ring for welding directly to the storage binsilo
Ductile iron hanger arms with rubber bushings
Black EPDM inlet and outlet socks with drawbands
Internal pressure cone
Vibratory motor with adjustable eccentric weights
View Complete Details

VRS16 Vacuum Sequencing Receiver

This pellet receiver utilizes a screen to aid in the separation of the pellets from the conveying air.

304 stainless steel product contact and aluminum clean air contact surfaces
Quick release V-Band clamp allows tool-less access for clean out and ease of maintenance
Optional mounting ring with neoprene sleeve
Receiver select valve for vacuum sequencing service - NEMA 4 enclosure
Gravity, flapper type, discharge valve with proximity sensor to monitor valve position. Other valve configurations available.
Perforated screen filter media constructed of stainless steel.
Radial inlet with internal gravity swing check valve. Reduces reverse blow back air going back into the convey line and creates a positive vacuum seal for a common material convey line.
View Complete Details

Fluid Flow Hopper

  • Series FFH
This hopper uses low pressure air to aid flow of difficult to handle powders. The Fluid Flow Hopper requires an air source which is typically regulated compressed air.

STANDARD CONSTRUCTION FEATURES

This device is for use as a flow aid with difficult to handle powders (i.e. titanium dioxide) from a binhopper by utilizing low pressure air to aerate and flex the material inside the hopper
60 Degree hopper with flanged product discharge
Permeable flow liner constructed of a thick needled, non-woven polyester
Liner features integral vinyl inlet and outlet flanges (gaskets)
Factory installed air manifold (Customer is responsible, unless specifically included in the proposal, for air source and supply line from the air source to the air manifold). Air supply can be provided by a stand alone pressure blower package or compressed air source.
Unit requires approximately 5 CFMSq. Ft. of clean, dry air at a pressure of 1-7 PSIG
View Complete Details

FFH Fluid Flow Hopper

  • Pressure 1-7 PSIG
This hopper uses low pressure air to aid flow of difficult to handle powders. The Fluid Flow Hopper requires an air source which is typically regulated compressed air.

STANDARD CONSTRUCTION FEATURES

This device is for use as a flow aid with difficult to handle powders (i.e. titanium dioxide) from a binhopper by utilizing low pressure air to aerate and flex the material inside the hopper
60 Degree hopper with flanged product discharge
Permeable flow liner constructed of a thick needled, non-woven polyester
Liner features integral vinyl inlet and outlet flanges (gaskets)
Factory installed air manifold (Customer is responsible, unless specifically included in the proposal, for air source and supply line from the air source to the air manifold). Air supply can be provided by a stand alone pressure blower package or compressed air source.
Unit requires approximately 5 CFMSq. Ft. of clean, dry air at a pressure of 1-7 PSIG
View Complete Details

Exposed Pole Inline Magnet

  • Series EPT
This magnet will seperate metals from the product stream.

STANDARD CONSTRUCTION FEATURES

Leak-resistant flat to flat seal for line pressures up to 15 psi
Lorenz T-Handle clamps for a positive seal
304 Stainless steel housing for long, non-corrosive life
Rare earth model features door mounted magnet for cleaning off collected metal outside of the flow
45 MgOe Rare Earth Magnet

OPTIONAL FEATURES

Grade 8 Ceramic Magnets
Standard pipe-size ends
Custom line sizes
ANSI bolt pattern flanges
ANSI spec flanges
Food grade finish and welds
Sanitary finish and welds
Magnet mounted to cart for portable pneumatic bulk unloading applications
View Complete Details

EZ Clean Drawer Magnet

  • Series IMH
This magnet will separate metals from the product stream.

STANDARD CONSTRUCTION FEATURES

Reduced height, designed for replacing manual clean housings
316, 304 stainless steel housing and flanges
UHI50 (50 MgOe) Rare Earth magnetic tubes (Ceramic 8 magnets also available)
1 diameter tubes on 2 vertical and horizontal centers
Neoprene gasket material for dust control
FDA white BUNA wiper seals
Hinged rear access door
Collection pan for metal
Positive locking clamps for drawer
Gas shocks or compression springs for seal plate positioning

OPTIONAL FEATURES

Self cleaning, air operated, for remote installations, frequent cleaning, or fully automated system
Wear resistant tube treatment and special wiper seals for abrasive products (request OX literature for more information)
Custom sizes and transitions available
Food grade gasket material
Finish and welding treatments available for food and sanitary grade applications
Alternate tube spacing for special applications
316L stainless steel construction
Custom housing designs for magnet in hopper or angled chute installations
Individual cleaning drawers (adds to height)

OPTIONAL SELF-CLEANING FEATURE

The air-actuated stripper seal assembly discharges collected tramp metal into a catch pan as the drawer
View Complete Details

Inline Bullet Magnet

  • Series BM
This magnet will seperate metals from the product stream.

STANDARD CONSTRUCTION FEATURES

Leak-resistant silicon seal (factory tested to 15psi)
Easy clean stripper sleeve is standard on Rare Earth models (excluding 3 model)
45 MGOeRare Earth Magnetic Material (optional Ceramic 8 Magnet material also available)
Gas springs to assist door opening on 6 and 8 models (except Horizontal Side Mounted Installation)
Magnet mounted on hinged door to allow removal from product flow when cleaning
Stainless steel construction for long, non-corrosive life

OPTIONAL FEATURES

316L stainless steel construction
Cart mounting for load-out
Standard pipe-size ends
Food grade finish and welds
Sanitary finish and welds
ANSI bolt pattern flanges
ANSI spec flanges
Side mounted hinges
Custom line sizes
View Complete Details

SB Storage Bin

This bin stores ingredients without metering outflow and without an inline blower or fan.

STANDARD CONSTRUCTION FEATURES

60 Degree hopper with flanged product discharge
Closed top with flanged inlet
Two (2) half couplings for mounting of high and low level indicator
Four (4) support lugs
Lifting lugs

OPTIONAL FEATURES

Available in carbon steel, stainless steel or aluminum construction
Tangential inlet
Support legsstructure
PressureVacuum relief valve
PressureVacuum rated versus standard atmospheric design
InspectionAccess opening
IndustrialFood grade epoxy interior
Smooth not Flush (80 grit) or Smooth and Flush (120 grit) weld seams
70 Degree hopper slope
Asymmetric hopper configuration (offset)
Flange for mounting of vent filter
Additional sidewall height to provide surgestorage capacity
Vent sock for venting of displaced air
Various flow aids (e.g., fluidizer pads, bin vibrator, bin activator, etc.)
Various point level indicators (e.g., rotary, capacitance, proximity, etc.)
10 sloped top
View Complete Details

Central Vacuum System

The investigation of large scale combustible dust incidents usually reveals that the event is less damaging and costly in facilities with good housekeeping. Our central vacuum system is an essential part of an effective housekeeping program. Having a vacuum system handy to clean up ingredients or product will reduce exposure to allergens or carcinogens and minimize the amount of time employees spend on cleanup and maintenance. Because it helps keep combustible materials out of the air, our solution meets NFPA 654 standards for the prevention of fire and dust explosion.
View Complete Details

Stainless Steel Hose

Medium Duty - Most popular series. General duty transfer hose for moderate handling, and for dry bulk materials that are mildly abrasive.

Heavy Duty - Transfer hose for moderate to heavy handling with additional resistance to internal abrasio
View Complete Details

Railcar Unload Manifold

This is a piping assembly used to connect a vacuum conveying system for the purpose of unloading railcars.
This is a piping assembly used to connect a vacuum conveying system for the purpose of unloading railcars.
View Complete Details

Lump Breaker

  • Series LB1212
This lump breaker breaks up lumps that may happen with product during production as long as the product is soft enough to be broken mechanically. The lump breaker uses rotary knives to break down product.

STANDARD CONSTRUCTION FEATURES

Carbon steel or stainless steel construction
12 x 12 inside square inlet and outlet
Two (2) shafts with 12 square, fingers
Two (2) sets of 12 square fingers welded to housing interior
Outboard bearings with concentric locking collar
External seals
Factory assembled rotor shaft air purge assembly complete with single solenoid air control valve, regulator and interconnecting air line - NEMA 4 enclosure
Gear guard painted safety orange
2 HP, direct drive, gearmotor with TEFC enclosure

OPTIONAL FEATURES

X-Proof drive assembly
Carbon steel or stainless steel inlet andor outlet transitions
View Complete Details

Filter Bag Materials

The HorizonPSI SideWinder filter utilizes banks of individual filter racks to separate the material and air. Each rack contains 15 SpiroTubes (spiral formed tubes) that are supported in a single compact frame. The tubes are sonically welded to ensure airtight construction.

The 1.02" diameter of each SpiroTube provides an optimal relationship between the total unit area and the open area between the tubes. This decreases face velocities and increases airflow in four directions between the elements, enabling better control of the air stream velocities and increased dust release capacities. The one-piece self-supporting SpiroTubes are made of spun bonded polyester media laminated with an expanded PTFE membrane. This filter media can operate in temperatures up to 176 degrees F.

FEATURES & BENEFITS

Extremely low pressure drop, even at high air-to-cloth ratios.
Extremely low emissions - less than 1.0 mgNm3. This 99.99+% efficiency is a result of the spun bonded filter media and the expanded PTFE membrane.
Excellent dust release characteristics allow for improved, increased airflow and reduce differential pressure.
The one-piece filter rack design reduces installation time and maintenance requirements.
Operate at higher than normal air-to-cloth ratios for increase throughout.
View Complete Details

Shear Protector

  • Series SPT
The shear protector is for use with products that have large particals or are pelletized in nature and is designed to reduce the amount of product shear between the airlock rotor vanes and housing.
View Complete Details

Blow Thru Adaptor

  • Series BTR
This adaptor is used on airlocks to efficiently introduce the material into the conveying air stream. The unit is designed to match the airlock discharge and tube or pipe conveying line. It is available in carbon steel, stainless steel or aluminum construction.
View Complete Details

Small Bag Dum

  • Series RDCR
This is a manually operated bag dump that requires a worker to physically lift and cut open the bag. This unit requires a connection to a separate dust collection system to control the dust created from dumping bags.

STANDARD CONSTRUCTION FEATURES

60 degree hopper, nominal, with flanged product discharge
Hinged access door with gas springs to keep the door in the open or closed position
34 Wide x 12 deep removable grating
Removable air baffle
36 Wide x 9 deep bag resting shelf
Support legs to provide 24 clearance beneath the discharge flange
6 O.D. stub for connection to central dust collection system

OPTIONAL FEATURES

Carbon steel or 304 stainless steel construction
Various hopper slopes andor configurations
Access platform to maintain dump height to less than 40
Hydraulic bag compactor
Additional straight wall height to provide storagesurge capacity
View Complete Details

Railcar Unloading Sled

This "sled" slides beneath gravity hopper railcars for connecton to a vacuum unloading system.

Our railcar unloading sled is designed to mate to a gravity flow railcar equipped with a 32" x 24" centerflow enterprise gate.

The unit is supplied with four casters to allow for positioning of the sled under the railcar discharge. Once in position the operator then raises the pan into position by manually actuating the air cylinders. Conveying rate from the railcar is controlled by manually adjustable feed tube and air intake assemblyAluminum product contact surfaces
Male adaptor for conveying line hose connection
Air intake screen with carbon steel weather hood
Air intake adjustment damper
Manual flow control adjustment
Four (4) compact air cylinders to raise hopper to railcar outlet
Heavy duty casters wswivel mount plate and polyurethane tread
Carbon steel frame with standard White enamel exterior

Optional features:

Carbon or Stainless steel product contact surfaces
Unloading pan only (no sled).
View Complete Details

BV Bin Vibrator

  • capacit 5 to 15 cubic feet
Fluidizer pads located within the hopper are operated by pulsing air on and off. As the pads are pushed out with airflow, they will vibrate the sides of the hopper and push air outwards amongst the sides of hopper in order to increase or resume product flow by breaking loose compacted or sluggish materials from the hopper cone.

STANDARD CONSTRUCTION FEATURES

Cast ductile iron housing
Impacting type model to produce a metal-to-metal contact at the mounting plate which is the most effective in eliminating difficult flow problems
Air operated
Designed for a maximum hopperbin capacity of 5 to 15 cubic feet
Filtered and lubricated compressed air at 60 PSIG maximum required and is to be supplied by buyer
View Complete Details

Sound Enclosure

The Sound Enclosure dampens the sound created by the blower package.

STANDARD CONSTRUCTION FEATURES

Corrosion-resistant aluminum construction
4-Door entry provides easy access to the blower package
Flat, lift-off roof
PSI #618 Composite acoustical foam featuring fire resistance, mold and mildew resistance and UV inhibitors. Also resistant to oil and other chemicals
Sound attenuation tested from 20-30 dBA (testing required for performance guarantee)
Acoustically engineered air inlet box
Drip edge for all weather installations
Ventilator fan size based on heat load calculations
Zinc-plated hinges and hardware
View Complete Details

Hopper Fluidizer Group

  • Series HFG
The fluidizer pads are typically operated by pulsing the air on and off. The actual SCFM is calculated by multiplying the Pulse On Time In Seconds by the air flow at the supply pressure times the number of pads utilized.

A typical example would be that of a hopper requiring (4) pads with an on time of 2 seconds and an off time of 10 seconds at a supply pressure of 30 PSIG. This scenario would result in a total SCFM requirement of 13.4 SCFM. 60 seconds12 seconds total cycle time = 5 cycles per minute; 5 cycles per minute x 0.67 (air flow at 30 PSIG) x 4 fluidizer pads. The actual number of pads is dependent upon the application.

STANDARD CONSTRUCTION FEATURES

Fluidizer pads (maximum of 4 air pads per manifold assembly quantity of air pads required will vary based on application parameters)
White silicone disk
Stainless steel stem
White, food grade, o-ring
Flat washer and hex nut
Internally threaded for 14 NPT male connector
Air control assembly complete with the following:
Air manifold, factory installed, complete with interconnecting air line and fittings
Pressure regulator with gauge
Single solenoid valve to allow for remote (hand switch) or automatic (timer or PLC) operation -120 VAC, NEMA 4 enclosure

OPTIONAL FEATURES

NEMA 9 solenoid enclosure
Timer control board
Air accumulator tank
E-Z In assemblies ideal for retrofitting existing hoppers or bins, or when frequent inspection and maintenance is required. Once installed, you can also perform regular inspection and maintenance as required from the outside, without confined space entry requirements, saving you both time and money.
View Complete Details

2-Way Line, Flex Tube Diverte

  • Series HFTV
This valve is more affordable than a plug diverter. It can also be used in dense phase conveying, yet shouldn't be used with abrasive materials.

STANDARD CONSTRUCTION FEATURES

Aluminum valve frame, covers and end plates
304 Stainless steel weatherproof housing and flex tube support
304 Stainless steel blade
Gates 690 SB natural rubber-lined flex hose
Food grade nylon pressure plates and silicone rubber load seals
Carbon steel, aluminum or stainless steel line adaptors
Double acting air cylinder
Single solenoid air control valve, NEMA 4 enclosure
Two (2) magnetic reed type proof switches, NEMA 6 enclosure

OPTIONAL FEATURES

Stainless steel hose
High temperature design (up to 350 F)
304 Stainless steel, electropolished, blade versus standard 304 stainless steel
Food grade PET or UHMW pressure plate seals versus standard nylon
View Complete Details

Continuous Level Indicator

  • Series RCL
This level continuous indicator utilizes hermetically sealed strain sensors to monitor level of product in storage silos, hoppers, and bins.

STANDARD CONSTRUCTION

Precision electronic strain sensing with hermetically-sealed stainless steel strain sensor (U.S. patent no. 4530245)
Sensor mounted externally to the bin, which eliminates contamination or corrosion that can result from contact with the monitored product
Incorporation of the sensor as an integral part of the support member cancels temperature effects common to so-called bolt-on sensors, eliminating the need for protective insulation
Accurate to within 2%
CL-100 Control
Enclosure Polystyrene plastic; IP-64 weather-tight
Temperature Range -10C to +50C; Temperatures down to -40C will not damage unit
Power Requirements Less than 10 W; 120240 VAC selectable; -15% to +10%; 48-62 Hz
Outputs Three (3) SPDT dry contacts rated 5 A at 250 VAC (low, high, overflow)
Optional 4-20 mA output proportional to level indication
Display 50-segment LED bar graph changes in 2% increments
View Complete Details

Vacuum Pick-Up Single VPS Series

This vacuum pick-up is a way of introducing product into the airflow without the use of an airlock.

STANDARD CONSTRUCTION FEATURES

Available in carbon steel, 304 stainless steel or 316 stainless steel construction.
Collection hopper with line connection
Butterfly Valve
Wafer style cast iron body with polyester coating
Nylon coated, ductile iron disc
White EPDM seat
Manual operator with notch plate handle to lock the valve in any of 10 positions
Air inlet filter
View Complete Details

Air Intake Assembly

  • Series AIA
Our Air Intake Assembly is utilized at the intake of a vacuum conveying system in order to filter out impurities in the air prior to entering the conveying system.
View Complete Details

PVC Hose-Rubber

Polyvinyl chloride hose used for where flexible connections are required. It is coated in rubber for more heavy-duty applications. Below are the different series available.
View Complete Details

Vacuum Blower

  • Series VBH
The Vacuum Blower VBH Series utilizes negative air pressure to convey the material. The motive airpressure is produced by a positive displacement blower which is located at the end of the conveying system.

Inline filter prevents material from entering blower in case of a bag leak
Air operated vacuum breaker valve allows blower to come up to speed under a no load condition and protect the blower against a high vacuum condition (open based on vacuum switch setting if programmed into process controls)
Positive displacement blower - all major brands available
Electric motor and adjustable mount base 230460 V, 3 Ph, 60 Hz all major brands, enclosures and efficiency ratings available
Discharge weatherhood prevents birds and large debris from entering discharge silencer while in the off condition
Combination chamber absorption discharge silencer reduces noise radiation in the vicinity of the package
V-Belt drive assembly and drive guard drive guard features access via removable doors, slotted front and drop through bottom
Vibration isolation and expansion joint isolates blower from the silencer to prevent fatigue stresses to the silencer
View Complete Details

RDCR Small Bag Dump

This is a manually operated bag dump that requires a worker to physically lift and cut open the bag. This unit requires a connection to a separate dust collection system to control the dust created from dumping bags.

STANDARD CONSTRUCTION FEATURES

60 degree hopper, nominal, with flanged product discharge
Hinged access door with gas springs to keep the door in the open or closed position
34 Wide x 12 deep removable grating
Removable air baffle
36 Wide x 9 deep bag resting shelf
Support legs to provide 24 clearance beneath the discharge flange
6 O.D. stub for c
View Complete Details

Heat Exchanger

  • Series AA
The Heat Exchanger AA Series removes heat from the convey air without the use of coolant.

AA Series exchangers feature a TEFC 230460 VAC, 3 phase motor, a heavy duty cooling fan and an OSHA approved fan guard. The exhaust hood is galvanized steel, and the venturi frame is painted carbon steel. These exchangers are ideal for locations with limited access to cooling water.

CORE CONSTRUCTION
The aluminum plate-fin core is furnace brazed with alternating finned flow channels. Process gas flows in horizontal channels, and ambient cooling air flows upward through the vertical channels. The process stream enters and exits through rectangular aluminum headers, which are welded to the core.

OPERATIONAL CONSIDERATIONS
Each process gas passageway is .02 square inches (.25 x .08 inches). The process stream must be filtered to ensure particulate will not obstruct the passages. If necessary, the service side can usually be cleaned with a soapy water wash. Due to their long flow length, the process channels should not be considered cleanable.

INSTALLATION CONSIDERATIONS
Pulsating flow, such as that produced by rotary lobe blowers, should be dampened by a chambered silencer. AA Series exchangers dissipate heat from the process stream to the ambient environment. They are designed for outdoor installation. If installed indoors, the area should be very well-ventilated.
View Complete Details

Insertable SideWinder

  • Series SWI
Our Insertable SideWinder Vent Filter features top loading filter media and offers easy media access, less downtime for maintenance and eliminates the need for confined space permitting. This is perhaps the most maintenance friendly filter available in the marketplace today.

STANDARD FEATURES

Quick opening, top mounted, hinged door provides tool-less access to filter media
Sloped clean air plenum to allow for water runoff
Reverse jet-pulse cleaning complete with a compressed air header and diaphragm valves
Adjustable pulse timer board with solenoids pre-mounted in an enclosure
Spun bond polyester with PTFE membrane, top removal, filter media that are self-supporting 99.99% efficiency at 2 micron
Magnehelic differential pressure gauge pre-mounted

OPTIONAL FEATURES

Materials of Construction:
Carbon Steel or Stainless Steel
Surface Finishes:
Painted STEEL-IT silver for carbon steel
Industrial grade epoxy interior for carbon steel
80 grit with smooth welds or 120 grit with flush welds
Enclosure Type:
NEMA 4, NEMA 4X or NEMA 79
Voltage Requirements:
120 volt AC or 24 volt DC
Differential Pressure Gauge:
Photohelic gauge with contact switches or 4-20 mA transmitter
View Complete Details

Truck Loading Static Bag Filter Vents

The static filter has a weather hood to protect the filter bag. This is used for venting air where a pulse jet filter is not required.
View Complete Details

Hopper Fill Valve

  • Series HFV
The Hopper Fill Valve is a fillpass type diverter. The construction is similar to the HDV and HTV series diverter valves in that the housing, closed end single blade diverting rotor and end plates are machined to tight tolerances. End plates, seals and bearings are protected from the material flow by the diverter rotor hubs and, in addition, food grade lubricant is packed into the void area between the end plates and rotor hubs. This valve is designed to be mounted to the top of a hopper and connected to a convey line. When the rotor is in the diverted position the material in the convey line is directed into the hopper. When the rotor is in the through position the material in the convey line is directed past the hopper.

STANDARD CONSTRUCTION FEATURES

Carbon steel, machined, housing and end plates
Carbon steel conveying line adaptors
Machined, closed end diverting rotor
Lifetime sealed and lubricated ball bearings with eccentric locking collar
End plates, seals and bearings are protected from the material flow by the diverter rotor hubs and, in addition, food grade lubricant packed into the void area between the end plates and rotor hubs
Internal deflector plate to reduce material carryover
Air cylinder operator
Single solenoid air control valve NEMA 4
Two (2) proximity type proof switches NEMA 4

OPTIONAL FEATURES

Stainless steel construction
Chrome plated housing bore
Stainless steel diverting rotor
Double solenoid air control valve
NEMA 79 electrical enclosure
Flanged line connections
Ceramic coated tube adaptors
AR Plate diverting rotor
View Complete Details

Liquid Bulk Storage

These factory welded tanks are used for large storage of ingredients or product needed for manufacturing.These factory welded tanks are used for large storage of ingredients or product needed for manufacturing.
View Complete Details

Tubing

Tubing and piping is used to connect components and convey products.

ALUMINUM PIPE AND TUBING
Alloy 6063 ASTM B-221
6063 T-6 Straights
6063 T-1 Bends

CARBON-STEEL PIPE AND TUBING
Pipe ASTM A-53 This specification covers seamless and welded black and galvanized steel pipe
Tube ASTM A-513 This specification covers electric-resistance welded-carbon and alloy steel tubing for use as mechanical tubing

STAINLESS-STEEL PIPE AND TUBING
Pipe ASTM A-312 This specification covers seamless and welded stainless-steel pipe intended for high temperature and general corrosive service. Twenty-four grades are covered, the most common of which are 304, 316, 304L and 316L
Tube ASTM A-249 This specification covers stainless-steel tubing for general corrosion resisting and low- or high-temperature service.

GALVANIZED PIPE AND TUBING
Pipe ASTM A-53 Galvanized coated pipe
Tube ASTM A-513 Galvanized coated tube
Tube ASTM Galvanized tube

TUBING WALL THICKNESS
16 Gauge (.065" wall)
14 Gauge (.083" wall)
10 Gauge (.130" wall)
11 Gauge (.120" wall)
12 Gauge (.109" wall)

PIPING WALL THICKNESS
Schedule 10
2 = .154
3 to 4 = .120
5 to 6 = .134
8 = .148
10 = .165

Schedule 40
2 = .109
3 = .216
4 = .237
5 = .258
6 = .280
8 = .322
10 = .365
View Complete Details

Fluidizer Bed

  • Series FB
The fluidizing bed is utilized as a flow aid for products that are easily fluidizable and not susceptible to "caking" (i.e., flour, come calcium carbonates, some starches, etc.)

STANDARD CONSTRUCTION FEATURES

Carbon steel dished head and outlet stub
Perforated metal plate with two (2) annular support rings to support diffuser cloth
5 Ply, 316 thick, diffuser cloth
1 Drain with plug

OPTIONAL FEATURES

Stainless steel outlet stub
Stainless steel dished head and outlet stub
Pressure blower package to provide fluidization air
Mounting hardware and sealant
IndustrialFood grade epoxy interior
View Complete Details

FB Fluidizer Bed

The fluidizing bed is utilized as a flow aid for products that are easily fluidizable and not susceptible to "caking" (i.e., flour, come calcium carbonates, some starches, etc.)

STANDARD CONSTRUCTION FEATURES

Carbon steel dished head and outlet stub
Perforated metal plate with two (2) annular support rings to support diffuser cloth
5 Ply, 316 thick, diffuser cloth
1 Drain with plug

OPTIONAL FEATURES

Stainless steel outlet stub
Stainless steel dished head and outlet stub
Pressure blower package to provide fluidization air
Mounting hardware and sealant
IndustrialFood grade epoxy interior
View Complete Details

Pressure Blower Package

The Pressure Blower Package utilizes positive air pressure to convey the material. The motive airpressure is produced by a positive displacement blower which is located at the beginning of the conveying system.

Air intake filtersilencer - optional air intake filter
Positive displacement blower - all major brands available
V-belt drive assembly and drive guard - drive guards feature access via bolted removable doors, slotted front and drop through bottom
Electric motor and adjustable mount base - 230460 V, 3 Ph, 60 Hz; all major brands, enclosures and efficiency ratings available
Weighted pressure relief valve provides superior life compared to conventional spring loaded relief valves
Check valve prevents product from entering discharge silencer in the event of a high pressure or back pressure
Combination chamber - absorption discharge silencer reduces noise radiation in the vicinity of the package
Vibration isolation and expansion joint isolates blower from the silencer to prevent fatigue stresses to the silencer and piping
View Complete Details

Bulk Bag Fill Head

  • Series BBFH
This Fill Head is utilized to assist in filling bulk bags by providing an inflatable seal to secure and seal the spout of the bulk bag.

STANDARD CONSTRUCTION FEATURES

8 Inlet flange with ANSI bolt pattern
Design to match a 14 16 diameter maximum bulk bag fill spout (Buyer to advise actual size)
Heavy duty rubber air bladder sleeve
Factory mounted manual air control valve and regulator
Two (2) Model Number F-235P-300 Air Intake Filter
8.3 Square feet of cloth area
Designed for a maximum of 300 cfm
3 Flanged line connection
Carbon steel weather hood

OPTIONAL FEATURES

Carbon steel or stainless steel product contact surfaces
Support stand with adjustable bag support arms constructed of 4, carbon steel, square tubing with adjustable bulk bag support arms
Varying baginlet dimensions
View Complete Details

Pneumatic Tube Railcar Unloading Components

These assorted products use pneumatics to move product from railcars and into convey systems including adaptors, filters and hatch vents for rail cars.
View Complete Details

Scale Hopper

  • Series SH
This hopper aids in metering and weighing product and typically is used when the hopper is being pneumatically filled via a Hopper Fill Valve.

STANDARD CONSTRUCTION FEATURES

Utilized when the hopper is being pneumatically filled via a HopperScale Fill Valve
60 Degree hopper with flanged product discharge
Closed top with flanged inlet
Mechanical vacuum breaker valve with vent sock to allow the hopper to breathe air in during the discharge cycle
One (1) half couplings for mounting of high level indicator
Three (3) support lugs
Lifting lugs
View Complete Details

BBFH Bulk Bag Fill Head

  • diameter 14“ – 16”
  • Model Number F-235P-300
This Fill Head is utilized to assist in filling bulk bags by providing an inflatable seal to secure and seal the spout of the bulk bag.

STANDARD CONSTRUCTION FEATURES

8 Inlet flange with ANSI bolt pattern
Design to match a 14 16 diameter maximum bulk bag fill spout (Buyer to advise actual size)
Heavy duty rubber air bladder sleeve
Factory mounted manual air control valve and regulator
Two (2) Model Number F-235P-300 Air Intake Filter
8.3 Square feet of cloth area
Designed for a maximum of 300 cfm
3 Flanged line connection
Carbon steel weather hood
View Complete Details

Desiccant Dehumidifier

MINIPAC DEHUMIDIFIER

The MIniPAC dehumidifier is the ideal dehumidification solution for smaller facilities in need of reliable humidity control or mold and mildew protection. The MIniPAC can be installed as a stand-alone unit, or attached to any central air conditioning system to enhance the system's dehumidification capability. A small, yet powerful unit that combats the effects of moisture in a wide variety of applications. Compact off the shelf sizes from 100 to 600 CFM.

Suitable for continuous operation
AutoManual selector switch
Power on, heater on and fault status indication
Independent blower for each air stream
Volume control dampers

VFB DEHUMIDIFIER

Custom engineered units with sizes from 300 to 30, 000 CFM. The VFB is the ideal dehumidification solution for facilities in need of custom built reliable temperature and humidity control.

Electric, stream, direct or indirect fired gas reactivation
Easy to remove desiccant rotor
Cleanable or disposable 30% inlet air filters
Relay-based controls for simple reliable operation
Hinged filter access doors with quick release fasteners
Circuit breakers (not fuses) for over-current protection
View Complete Details

Scaling System Weight Controller

  • Series HI 2151/30
This weight controller is connected to load cells and montors the weight of the product in bins, receivers, or other containers. This can be used in batching and loss-in-weight applications.

STANDARD CONSTRUCTION FEATURES

Six digit, fourteen segment LED display
Waterproof keyboard and weight display, NEMA 4 enclosure
Integrated Technician provides built-in system diagnostics
Displayed resolution, 1:985, 000
Update rate of 20 readings in 1 unit increments
Sliding averaging of up to 200 readings in 1 unit increments
Waversaver feature is adjustable
Gross or net modes of operation
Menu driven digital calibration
Front panel diagnostics
Auto zero tracking
Motion detection
Selectable RS-232C, 422 or 485 port
Two relay contact set points (SPDT, 3 amp, 115 VAC)
NBS certified (10, 000 counts)
Secure memory module
Remote functions connector
115 VAC, 5060 Hz operation

OPTIONAL FEATURES

Panel or wall mount
Output options Analog, Binary Coded Decimal, Remote IO (RIO) Interface to the Allen-Bradley Network, PROFIBUS Interface, Dynamic Data Exchange (DDE)
Control options Peak Hold, Rate-Of-Change
Set Point Options - TTL(Transistor - Transistor Logic) Level Output , External Setpoint Relays Card
240 VAC 5060 Hz Input Voltage
NISTNTEP Certification Mode Kit (-E3 except for -F4 wall mount)
Portable Display and Keypad (-E4)
Intrinsic Barrier Assembly
View Complete Details

Ceram-Back Elbows

Ceramic coated elbows are used for instances where large particle impact or abrasion is a problem during turns or diversions in product lines.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Horizon Systems, Inc.)
  • Lawrence, KS 66046 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/horizon-systems-inc/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0007457888{main}( ).../index.php:0
20.02092179800include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.03732902384include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.04613838080header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice