Post Buy Requirement

HS

Horizon Systems, Inc.

United States

Add Review

Our Products

Other Products / Services #5216736

Mist Air Purifier

Mist Air Purifier

Series MAP

Our Mist Air Purifier is designed to filter fines from extruders, preconditioners and coaters. Using water injection nozzles, the fines are captured and transported to the waste drain. The capturing of these fines can help reduce contamination sites for bacterial growth and reduce downtime for routine equipment cleaning. STANDARD CONSTRUCTION FEATURES 304 Stainless steel product contact surfacesInterior product contact welds continuous and ground flush to 120 gritExterior welds continuous3 HP, 304 stainless steel, washdown duty motor, Rated for 185 degrees FBelt drive arrangement with 304 stainless steel guard304 Stainless steel foot pedestal500 CFM airflowWater consumption 2 G.P.M.Integral 4 mesh filter media34 Fines and condensate drainInternal baffle and drainSafety grid on back opening in rear plateSplash baffle with drain pan for external filterWater addition nozzle18 Stainless steel0.7 GPM at 20 PSIMust be installed in convey line near pre-conditioner ventSupport legs, 304 stainless steel, for floor mounting of the unit complete with leveling feet, 12 max clearance

View Complete Details

Ask Latest Price & Details

SideWinder Filter Receiver

SideWinder Filter Receiver

Series SWR

The SideWinder filterreceiver features an easy open clean air plenum for side access to the top removal style, self-supporting filter cartridges. OPTIONAL FEATURES Available in carbon steel, stainless steel or aluminum constructionHigh entry inlet with baffles to protect bags from direct contact by the productNEMA 4X or NEMA 79 timer enclosureSupport legsMaintenance access ladder and platformInspectionAccess openingIndustrialFood grade epoxy interiorSmooth not Flush (80 grit) or Smooth and Flush (120 grit) weld seams70 Degree hopper slopeExplosion relief ventFlanged product inletclean air outletPulse on demand differential pressure gauge andor switch

View Complete Details

Ask Latest Price & Details

Dense Phase Transporter

Dense Phase Transporter

Series DPT

This is a pressure vessel that utilizes compressed air to convey products in dense phase. Standard Construction Features 60 degree cone bottomShort radius 90 degree elbow product discharge connectionInlet with butterfly valve NEMA 4 enclosureVent connection with butterfly valve NEMA 4 enclosureCompressed air inlet connectionInspection portmanwayExhaust port with manual ball valveCoupling for high level indicatorPressure switch - NEMA 4 enclosureLiquid filled conveying pressure gaugeSupport legsAir Control Assembly complete with the following:Air filterConvey pressure regulatorPilot operated pressure regulatorFlange mounted venturi nozzleOnOff control butterfly valve - NEMA 4 enclosureThree (3) Manual shut off valves with barbed hose connectionsGalvanized pipe fittings and support stand OPTIONAL FEATURES Available in carbon steel or stainless steel constructionNEMA 79 electrical enclosuresLine boostersIndustrialFood grade epoxy interiorSmooth not Flush (80 grit) interiorSmooth and Flush (120 grit) interior70 Degree hopper slopeAir accumulator

View Complete Details

Ask Latest Price & Details

KleenLift - Extruder Hood

KleenLift - Extruder Hood

Series KLU

The extruder hood is the pick-up point of a negative air lift system. It utilizes purified air to the convey the product from the extruder to a receiver that typically feeds a dryer. STANDARD FEATURES Laminar air distribution eliminates clumping and tumbling and optimizes velocity at the die area.Custom engineered interface between the hood, extruder barrel and knife drive.Air bypass system delivers airtight shutoff when diverted, easier service and wear reduction of blade seal.Sanitary design throughout the hood minimizes opportunity for product build up and hot spots and includes:Treated air supply options with HEPA filtration to eliminate finish product contamination.Sanitary access door, on clean side main shell, for easy cleaning.Designed for heat treatment or burnout temperatures up to 300 degrees F.FESTO Clean Design Solenoid Block for safe washdown and easy accessibility.Actuated lower clamshells to eliminate product build up during rejectbypass.Added safety features such as:Rod lock cylinders on main clamshells to lock main shells in place for operator safety and positive controlNEMA 4X electrical enclosure separates electrical and pneumatic connections.Pressure transducer for die chamber pressure verification and trending.Profected gasket design to provide superior overall fit up and easy replacement in the field.Large viewing windows for visual inspection of cutter and die while in operation.CE Compatible Options: Pressure fan for positive pressure at the dieHEPA FiltrationSteam or Gas Heated Air SupplyOzone

View Complete Details

Ask Latest Price & Details

ReelKLeen

ReelKLeen

The HorizonPSI ReelKleen system is an innovative way to ensure the proper sanitation of your supply line. The compact device applies a low volume spray of sanitizing agent to the interior of your cleaned conveying line. It minimizes the use of sanitizing solution, equipment and labor needed to keep your line safe. Any low viscosity pump-able solutionACSPhresh (Acidified Calcium Sulfate)Quaternary (Quat) Sanitizing AgentAlcohol based solutions (possible safety hazards from vapors)Other agents that are customer recognizedapproved STANDARD FEATURES Compressed airSpray valveMix valveMix tankReel motorSpeed controlDiaphragm pumpDrain valveReel motor foot switch120 volt powered hose reel

View Complete Details

Ask Latest Price & Details

Replaceable Back Elbow

Replaceable Back Elbow

The economical feature of this elbow is in the convenience of replacing the outer radius back, where the most wear occurs, without replacing the entire elbow. This type of elbow is also more economical than a tube bend elbow when the size of the tube or pipe exceeds 10"" diameter. The elbows are constructed of 12 gauge carbon steel with a 10 gauge abrasion resistant removable back. They are available in carbon steel or stainless steel construction.

View Complete Details

Ask Latest Price & Details

Clear Air Exhaust Fans

Clear Air Exhaust Fans

Series HS

The clean air exhaust fan is connected to the vent filter plenum to aid in evacuation of air from the vent filter. STANDARD CONSTRUCTION FEATURES Split housing for maintenance easeEven O.D. pipe sizes on inlet and outletNon-Sparking cast aluminum wheel and housingAssortment of wheel sizes to pinpoint your performance requirementsReliabilityWheels both statically and dynamically balancedRustproof OPTIONAL FEATURES Carbon steel or stainless steel constructionInletOutlet damperDischarge silencerX-Proof motor enclosureBelt driven versus standard direct driven

View Complete Details

Ask Latest Price & Details

CBA Bin Activator

CBA Bin Activator

This bin emits vibrations in hoppers in order to "shake" the product and break up lumps or stoppages in storage silos. STANDARD CONSTRUCTION FEATURES 45 Degree or unique 3060 degree cone designWeld-On adaptor ring for welding directly to the storage binsiloDuctile iron hanger arms with rubber bushingsBlack EPDM inlet and outlet socks with drawbandsInternal pressure coneVibratory motor with adjustable eccentric weights

View Complete Details

Ask Latest Price & Details

VRS16 Vacuum Sequencing Receiver

VRS16 Vacuum Sequencing Receiver

This pellet receiver utilizes a screen to aid in the separation of the pellets from the conveying air. 304 stainless steel product contact and aluminum clean air contact surfacesQuick release V-Band clamp allows tool-less access for clean out and ease of maintenanceOptional mounting ring with neoprene sleeveReceiver select valve for vacuum sequencing service - NEMA 4 enclosureGravity, flapper type, discharge valve with proximity sensor to monitor valve position. Other valve configurations available.Perforated screen filter media constructed of stainless steel.Radial inlet with internal gravity swing check valve. Reduces reverse blow back air going back into the convey line and creates a positive vacuum seal for a common material convey line.

View Complete Details

Ask Latest Price & Details

Fluid Flow Hopper

Fluid Flow Hopper

Series FFH

This hopper uses low pressure air to aid flow of difficult to handle powders. The Fluid Flow Hopper requires an air source which is typically regulated compressed air. STANDARD CONSTRUCTION FEATURES This device is for use as a flow aid with difficult to handle powders (i.e. titanium dioxide) from a binhopper by utilizing low pressure air to aerate and flex the material inside the hopper60 Degree hopper with flanged product dischargePermeable flow liner constructed of a thick needled, non-woven polyesterLiner features integral vinyl inlet and outlet flanges (gaskets)Factory installed air manifold (Customer is responsible, unless specifically included in the proposal, for air source and supply line from the air source to the air manifold). Air supply can be provided by a stand alone pressure blower package or compressed air source.Unit requires approximately 5 CFMSq. Ft. of clean, dry air at a pressure of 1-7 PSIG

View Complete Details

Ask Latest Price & Details

FFH Fluid Flow Hopper

FFH Fluid Flow Hopper

Pressure 1-7 PSIG

This hopper uses low pressure air to aid flow of difficult to handle powders. The Fluid Flow Hopper requires an air source which is typically regulated compressed air. STANDARD CONSTRUCTION FEATURES This device is for use as a flow aid with difficult to handle powders (i.e. titanium dioxide) from a binhopper by utilizing low pressure air to aerate and flex the material inside the hopper60 Degree hopper with flanged product dischargePermeable flow liner constructed of a thick needled, non-woven polyesterLiner features integral vinyl inlet and outlet flanges (gaskets)Factory installed air manifold (Customer is responsible, unless specifically included in the proposal, for air source and supply line from the air source to the air manifold). Air supply can be provided by a stand alone pressure blower package or compressed air source.Unit requires approximately 5 CFMSq. Ft. of clean, dry air at a pressure of 1-7 PSIG

View Complete Details

Ask Latest Price & Details

Exposed Pole Inline Magnet

Exposed Pole Inline Magnet

Series EPT

This magnet will seperate metals from the product stream. STANDARD CONSTRUCTION FEATURES Leak-resistant flat to flat seal for line pressures up to 15 psiLorenz T-Handle clamps for a positive seal304 Stainless steel housing for long, non-corrosive lifeRare earth model features door mounted magnet for cleaning off collected metal outside of the flow45 MgOe Rare Earth Magnet OPTIONAL FEATURES Grade 8 Ceramic MagnetsStandard pipe-size endsCustom line sizesANSI bolt pattern flangesANSI spec flangesFood grade finish and weldsSanitary finish and weldsMagnet mounted to cart for portable pneumatic bulk unloading applications

View Complete Details

Ask Latest Price & Details

EZ Clean Drawer Magnet

EZ Clean Drawer Magnet

Series IMH

This magnet will separate metals from the product stream. STANDARD CONSTRUCTION FEATURES Reduced height, designed for replacing manual clean housings316, 304 stainless steel housing and flangesUHI50 (50 MgOe) Rare Earth magnetic tubes (Ceramic 8 magnets also available)1 diameter tubes on 2 vertical and horizontal centersNeoprene gasket material for dust controlFDA white BUNA wiper sealsHinged rear access doorCollection pan for metalPositive locking clamps for drawerGas shocks or compression springs for seal plate positioning OPTIONAL FEATURES Self cleaning, air operated, for remote installations, frequent cleaning, or fully automated systemWear resistant tube treatment and special wiper seals for abrasive products (request OX literature for more information)Custom sizes and transitions availableFood grade gasket materialFinish and welding treatments available for food and sanitary grade applicationsAlternate tube spacing for special applications316L stainless steel constructionCustom housing designs for magnet in hopper or angled chute installationsIndividual cleaning drawers (adds to height) OPTIONAL SELF-CLEANING FEATURE The air-actuated stripper seal assembly discharges collected tramp metal into a catch pan as the drawer

View Complete Details

Ask Latest Price & Details

Inline Bullet Magnet

Inline Bullet Magnet

Series BM

This magnet will seperate metals from the product stream. STANDARD CONSTRUCTION FEATURES Leak-resistant silicon seal (factory tested to 15psi)Easy clean stripper sleeve is standard on Rare Earth models (excluding 3 model)45 MGOeRare Earth Magnetic Material (optional Ceramic 8 Magnet material also available)Gas springs to assist door opening on 6 and 8 models (except Horizontal Side Mounted Installation)Magnet mounted on hinged door to allow removal from product flow when cleaningStainless steel construction for long, non-corrosive life OPTIONAL FEATURES 316L stainless steel constructionCart mounting for load-outStandard pipe-size endsFood grade finish and weldsSanitary finish and weldsANSI bolt pattern flangesANSI spec flangesSide mounted hingesCustom line sizes

View Complete Details

Ask Latest Price & Details

SB Storage Bin

SB Storage Bin

This bin stores ingredients without metering outflow and without an inline blower or fan. STANDARD CONSTRUCTION FEATURES 60 Degree hopper with flanged product dischargeClosed top with flanged inletTwo (2) half couplings for mounting of high and low level indicatorFour (4) support lugsLifting lugs OPTIONAL FEATURES Available in carbon steel, stainless steel or aluminum constructionTangential inletSupport legsstructurePressureVacuum relief valvePressureVacuum rated versus standard atmospheric designInspectionAccess openingIndustrialFood grade epoxy interiorSmooth not Flush (80 grit) or Smooth and Flush (120 grit) weld seams70 Degree hopper slopeAsymmetric hopper configuration (offset)Flange for mounting of vent filterAdditional sidewall height to provide surgestorage capacityVent sock for venting of displaced airVarious flow aids (e.g., fluidizer pads, bin vibrator, bin activator, etc.)Various point level indicators (e.g., rotary, capacitance, proximity, etc.)10 sloped top

View Complete Details

Ask Latest Price & Details

Central Vacuum System

Central Vacuum System

The investigation of large scale combustible dust incidents usually reveals that the event is less damaging and costly in facilities with good housekeeping. Our central vacuum system is an essential part of an effective housekeeping program. Having a vacuum system handy to clean up ingredients or product will reduce exposure to allergens or carcinogens and minimize the amount of time employees spend on cleanup and maintenance. Because it helps keep combustible materials out of the air, our solution meets NFPA 654 standards for the prevention of fire and dust explosion.

View Complete Details

Ask Latest Price & Details

Stainless Steel Hose

Stainless Steel Hose

Medium Duty - Most popular series. General duty transfer hose for moderate handling, and for dry bulk materials that are mildly abrasive. Heavy Duty - Transfer hose for moderate to heavy handling with additional resistance to internal abrasio

View Complete Details

Ask Latest Price & Details

Railcar Unload Manifold

Railcar Unload Manifold

This is a piping assembly used to connect a vacuum conveying system for the purpose of unloading railcars.This is a piping assembly used to connect a vacuum conveying system for the purpose of unloading railcars.

View Complete Details

Ask Latest Price & Details

Lump Breaker

Lump Breaker

Series LB1212

This lump breaker breaks up lumps that may happen with product during production as long as the product is soft enough to be broken mechanically. The lump breaker uses rotary knives to break down product. STANDARD CONSTRUCTION FEATURES Carbon steel or stainless steel construction12 x 12 inside square inlet and outletTwo (2) shafts with 12 square, fingersTwo (2) sets of 12 square fingers welded to housing interiorOutboard bearings with concentric locking collarExternal sealsFactory assembled rotor shaft air purge assembly complete with single solenoid air control valve, regulator and interconnecting air line - NEMA 4 enclosureGear guard painted safety orange2 HP, direct drive, gearmotor with TEFC enclosure OPTIONAL FEATURES X-Proof drive assemblyCarbon steel or stainless steel inlet andor outlet transitions

View Complete Details

Ask Latest Price & Details

Filter Bag Materials

Filter Bag Materials

The HorizonPSI SideWinder filter utilizes banks of individual filter racks to separate the material and air. Each rack contains 15 SpiroTubes (spiral formed tubes) that are supported in a single compact frame. The tubes are sonically welded to ensure airtight construction. The 1.02" diameter of each SpiroTube provides an optimal relationship between the total unit area and the open area between the tubes. This decreases face velocities and increases airflow in four directions between the elements, enabling better control of the air stream velocities and increased dust release capacities. The one-piece self-supporting SpiroTubes are made of spun bonded polyester media laminated with an expanded PTFE membrane. This filter media can operate in temperatures up to 176 degrees F. FEATURES & BENEFITS Extremely low pressure drop, even at high air-to-cloth ratios.Extremely low emissions - less than 1.0 mgNm3. This 99.99+% efficiency is a result of the spun bonded filter media and the expanded PTFE membrane.Excellent dust release characteristics allow for improved, increased airflow and reduce differential pressure.The one-piece filter rack design reduces installation time and maintenance requirements.Operate at higher than normal air-to-cloth ratios for increase throughout.

View Complete Details

Ask Latest Price & Details

Shear Protector

Shear Protector

Series SPT

The shear protector is for use with products that have large particals or are pelletized in nature and is designed to reduce the amount of product shear between the airlock rotor vanes and housing.

View Complete Details

Ask Latest Price & Details

Blow Thru Adaptor

Blow Thru Adaptor

Series BTR

This adaptor is used on airlocks to efficiently introduce the material into the conveying air stream. The unit is designed to match the airlock discharge and tube or pipe conveying line. It is available in carbon steel, stainless steel or aluminum construction.

View Complete Details

Ask Latest Price & Details

Small Bag Dum

Small Bag Dum

Series RDCR

This is a manually operated bag dump that requires a worker to physically lift and cut open the bag. This unit requires a connection to a separate dust collection system to control the dust created from dumping bags. STANDARD CONSTRUCTION FEATURES 60 degree hopper, nominal, with flanged product dischargeHinged access door with gas springs to keep the door in the open or closed position34 Wide x 12 deep removable gratingRemovable air baffle36 Wide x 9 deep bag resting shelfSupport legs to provide 24 clearance beneath the discharge flange6 O.D. stub for connection to central dust collection system OPTIONAL FEATURES Carbon steel or 304 stainless steel constructionVarious hopper slopes andor configurationsAccess platform to maintain dump height to less than 40Hydraulic bag compactorAdditional straight wall height to provide storagesurge capacity

View Complete Details

Ask Latest Price & Details

Railcar Unloading Sled

Railcar Unloading Sled

This "sled" slides beneath gravity hopper railcars for connecton to a vacuum unloading system. Our railcar unloading sled is designed to mate to a gravity flow railcar equipped with a 32" x 24" centerflow enterprise gate. The unit is supplied with four casters to allow for positioning of the sled under the railcar discharge. Once in position the operator then raises the pan into position by manually actuating the air cylinders. Conveying rate from the railcar is controlled by manually adjustable feed tube and air intake assemblyAluminum product contact surfacesMale adaptor for conveying line hose connectionAir intake screen with carbon steel weather hoodAir intake adjustment damperManual flow control adjustmentFour (4) compact air cylinders to raise hopper to railcar outletHeavy duty casters wswivel mount plate and polyurethane treadCarbon steel frame with standard White enamel exterior Optional features: Carbon or Stainless steel product contact surfacesUnloading pan only (no sled).

View Complete Details

Ask Latest Price & Details

BV Bin Vibrator

BV Bin Vibrator

capacit 5 to 15 cubic feet

Fluidizer pads located within the hopper are operated by pulsing air on and off. As the pads are pushed out with airflow, they will vibrate the sides of the hopper and push air outwards amongst the sides of hopper in order to increase or resume product flow by breaking loose compacted or sluggish materials from the hopper cone. STANDARD CONSTRUCTION FEATURES Cast ductile iron housingImpacting type model to produce a metal-to-metal contact at the mounting plate which is the most effective in eliminating difficult flow problemsAir operatedDesigned for a maximum hopperbin capacity of 5 to 15 cubic feetFiltered and lubricated compressed air at 60 PSIG maximum required and is to be supplied by buyer

View Complete Details

Ask Latest Price & Details

Sound Enclosure

Sound Enclosure

The Sound Enclosure dampens the sound created by the blower package. STANDARD CONSTRUCTION FEATURES Corrosion-resistant aluminum construction4-Door entry provides easy access to the blower packageFlat, lift-off roofPSI #618 Composite acoustical foam featuring fire resistance, mold and mildew resistance and UV inhibitors. Also resistant to oil and other chemicalsSound attenuation tested from 20-30 dBA (testing required for performance guarantee)Acoustically engineered air inlet boxDrip edge for all weather installationsVentilator fan size based on heat load calculationsZinc-plated hinges and hardware

View Complete Details

Ask Latest Price & Details

Hopper Fluidizer Group

Hopper Fluidizer Group

Series HFG

The fluidizer pads are typically operated by pulsing the air on and off. The actual SCFM is calculated by multiplying the Pulse On Time In Seconds by the air flow at the supply pressure times the number of pads utilized. A typical example would be that of a hopper requiring (4) pads with an on time of 2 seconds and an off time of 10 seconds at a supply pressure of 30 PSIG. This scenario would result in a total SCFM requirement of 13.4 SCFM. 60 seconds12 seconds total cycle time = 5 cycles per minute; 5 cycles per minute x 0.67 (air flow at 30 PSIG) x 4 fluidizer pads. The actual number of pads is dependent upon the application. STANDARD CONSTRUCTION FEATURES Fluidizer pads (maximum of 4 air pads per manifold assembly quantity of air pads required will vary based on application parameters)White silicone diskStainless steel stemWhite, food grade, o-ringFlat washer and hex nutInternally threaded for 14 NPT male connectorAir control assembly complete with the following:Air manifold, factory installed, complete with interconnecting air line and fittingsPressure regulator with gaugeSingle solenoid valve to allow for remote (hand switch) or automatic (timer or PLC) operation -120 VAC, NEMA 4 enclosure OPTIONAL FEATURES NEMA 9 solenoid enclosureTimer control boardAir accumulator tankE-Z In assemblies ideal for retrofitting existing hoppers or bins, or when frequent inspection and maintenance is required. Once installed, you can also perform regular inspection and maintenance as required from the outside, without confined space entry requirements, saving you both time and money.

View Complete Details

Ask Latest Price & Details

2-Way Line, Flex Tube Diverte

2-Way Line, Flex Tube Diverte

Series HFTV

This valve is more affordable than a plug diverter. It can also be used in dense phase conveying, yet shouldn't be used with abrasive materials. STANDARD CONSTRUCTION FEATURES Aluminum valve frame, covers and end plates304 Stainless steel weatherproof housing and flex tube support304 Stainless steel bladeGates 690 SB natural rubber-lined flex hoseFood grade nylon pressure plates and silicone rubber load sealsCarbon steel, aluminum or stainless steel line adaptorsDouble acting air cylinderSingle solenoid air control valve, NEMA 4 enclosureTwo (2) magnetic reed type proof switches, NEMA 6 enclosure OPTIONAL FEATURES Stainless steel hoseHigh temperature design (up to 350 F)304 Stainless steel, electropolished, blade versus standard 304 stainless steelFood grade PET or UHMW pressure plate seals versus standard nylon

View Complete Details

Ask Latest Price & Details

Continuous Level Indicator

Continuous Level Indicator

Series RCL

This level continuous indicator utilizes hermetically sealed strain sensors to monitor level of product in storage silos, hoppers, and bins. STANDARD CONSTRUCTION Precision electronic strain sensing with hermetically-sealed stainless steel strain sensor (U.S. patent no. 4530245)Sensor mounted externally to the bin, which eliminates contamination or corrosion that can result from contact with the monitored productIncorporation of the sensor as an integral part of the support member cancels temperature effects common to so-called bolt-on sensors, eliminating the need for protective insulationAccurate to within 2%CL-100 ControlEnclosure Polystyrene plastic; IP-64 weather-tightTemperature Range -10C to +50C; Temperatures down to -40C will not damage unitPower Requirements Less than 10 W; 120240 VAC selectable; -15% to +10%; 48-62 HzOutputs Three (3) SPDT dry contacts rated 5 A at 250 VAC (low, high, overflow)Optional 4-20 mA output proportional to level indicationDisplay 50-segment LED bar graph changes in 2% increments

View Complete Details

Ask Latest Price & Details

Vacuum Pick-Up Single VPS Series

Vacuum Pick-Up Single VPS Series

This vacuum pick-up is a way of introducing product into the airflow without the use of an airlock. STANDARD CONSTRUCTION FEATURES Available in carbon steel, 304 stainless steel or 316 stainless steel construction.Collection hopper with line connectionButterfly ValveWafer style cast iron body with polyester coatingNylon coated, ductile iron discWhite EPDM seatManual operator with notch plate handle to lock the valve in any of 10 positionsAir inlet filter

View Complete Details

Ask Latest Price & Details

air intake assembly

Air Intake Assembly

Series AIA

Our Air Intake Assembly is utilized at the intake of a vacuum conveying system in order to filter out impurities in the air prior to entering the conveying system.

View Complete Details

Ask Latest Price & Details

PVC Hose-Rubber

PVC Hose-Rubber

Polyvinyl chloride hose used for where flexible connections are required. It is coated in rubber for more heavy-duty applications. Below are the different series available.

View Complete Details

Ask Latest Price & Details

vacuum blower

Vacuum Blower

Series VBH

The Vacuum Blower VBH Series utilizes negative air pressure to convey the material. The motive airpressure is produced by a positive displacement blower which is located at the end of the conveying system. Inline filter prevents material from entering blower in case of a bag leakAir operated vacuum breaker valve allows blower to come up to speed under a no load condition and protect the blower against a high vacuum condition (open based on vacuum switch setting if programmed into process controls)Positive displacement blower - all major brands availableElectric motor and adjustable mount base 230460 V, 3 Ph, 60 Hz all major brands, enclosures and efficiency ratings availableDischarge weatherhood prevents birds and large debris from entering discharge silencer while in the off conditionCombination chamber absorption discharge silencer reduces noise radiation in the vicinity of the packageV-Belt drive assembly and drive guard drive guard features access via removable doors, slotted front and drop through bottomVibration isolation and expansion joint isolates blower from the silencer to prevent fatigue stresses to the silencer

View Complete Details

Ask Latest Price & Details

RDCR Small Bag Dump

RDCR Small Bag Dump

This is a manually operated bag dump that requires a worker to physically lift and cut open the bag. This unit requires a connection to a separate dust collection system to control the dust created from dumping bags. STANDARD CONSTRUCTION FEATURES 60 degree hopper, nominal, with flanged product dischargeHinged access door with gas springs to keep the door in the open or closed position34 Wide x 12 deep removable gratingRemovable air baffle36 Wide x 9 deep bag resting shelfSupport legs to provide 24 clearance beneath the discharge flange6 O.D. stub for c

View Complete Details

Ask Latest Price & Details

heat exchanger

Heat Exchanger

Series AA

The Heat Exchanger AA Series removes heat from the convey air without the use of coolant. AA Series exchangers feature a TEFC 230460 VAC, 3 phase motor, a heavy duty cooling fan and an OSHA approved fan guard. The exhaust hood is galvanized steel, and the venturi frame is painted carbon steel. These exchangers are ideal for locations with limited access to cooling water. CORE CONSTRUCTIONThe aluminum plate-fin core is furnace brazed with alternating finned flow channels. Process gas flows in horizontal channels, and ambient cooling air flows upward through the vertical channels. The process stream enters and exits through rectangular aluminum headers, which are welded to the core. OPERATIONAL CONSIDERATIONSEach process gas passageway is .02 square inches (.25 x .08 inches). The process stream must be filtered to ensure particulate will not obstruct the passages. If necessary, the service side can usually be cleaned with a soapy water wash. Due to their long flow length, the process channels should not be considered cleanable. INSTALLATION CONSIDERATIONSPulsating flow, such as that produced by rotary lobe blowers, should be dampened by a chambered silencer. AA Series exchangers dissipate heat from the process stream to the ambient environment. They are designed for outdoor installation. If installed indoors, the area should be very well-ventilated.

View Complete Details

Ask Latest Price & Details

Insertable SideWinder

Insertable SideWinder

Series SWI

Our Insertable SideWinder Vent Filter features top loading filter media and offers easy media access, less downtime for maintenance and eliminates the need for confined space permitting. This is perhaps the most maintenance friendly filter available in the marketplace today. STANDARD FEATURES Quick opening, top mounted, hinged door provides tool-less access to filter mediaSloped clean air plenum to allow for water runoffReverse jet-pulse cleaning complete with a compressed air header and diaphragm valvesAdjustable pulse timer board with solenoids pre-mounted in an enclosureSpun bond polyester with PTFE membrane, top removal, filter media that are self-supporting 99.99% efficiency at 2 micronMagnehelic differential pressure gauge pre-mounted OPTIONAL FEATURES Materials of Construction:Carbon Steel or Stainless SteelSurface Finishes: Painted STEEL-IT silver for carbon steel Industrial grade epoxy interior for carbon steel 80 grit with smooth welds or 120 grit with flush weldsEnclosure Type:NEMA 4, NEMA 4X or NEMA 79Voltage Requirements:120 volt AC or 24 volt DCDifferential Pressure Gauge:Photohelic gauge with contact switches or 4-20 mA transmitter

View Complete Details

Ask Latest Price & Details

Truck Loading Static Bag Filter Vents

Truck Loading Static Bag Filter Vents

The static filter has a weather hood to protect the filter bag. This is used for venting air where a pulse jet filter is not required.

View Complete Details

Ask Latest Price & Details

Hopper Fill Valve

Hopper Fill Valve

Series HFV

The Hopper Fill Valve is a fillpass type diverter. The construction is similar to the HDV and HTV series diverter valves in that the housing, closed end single blade diverting rotor and end plates are machined to tight tolerances. End plates, seals and bearings are protected from the material flow by the diverter rotor hubs and, in addition, food grade lubricant is packed into the void area between the end plates and rotor hubs. This valve is designed to be mounted to the top of a hopper and connected to a convey line. When the rotor is in the diverted position the material in the convey line is directed into the hopper. When the rotor is in the through position the material in the convey line is directed past the hopper. STANDARD CONSTRUCTION FEATURES Carbon steel, machined, housing and end platesCarbon steel conveying line adaptorsMachined, closed end diverting rotorLifetime sealed and lubricated ball bearings with eccentric locking collarEnd plates, seals and bearings are protected from the material flow by the diverter rotor hubs and, in addition, food grade lubricant packed into the void area between the end plates and rotor hubsInternal deflector plate to reduce material carryoverAir cylinder operatorSingle solenoid air control valve NEMA 4Two (2) proximity type proof switches NEMA 4 OPTIONAL FEATURES Stainless steel constructionChrome plated housing boreStainless steel diverting rotorDouble solenoid air control valveNEMA 79 electrical enclosureFlanged line connectionsCeramic coated tube adaptorsAR Plate diverting rotor

View Complete Details

Ask Latest Price & Details

Liquid Bulk Storage

Liquid Bulk Storage

These factory welded tanks are used for large storage of ingredients or product needed for manufacturing.These factory welded tanks are used for large storage of ingredients or product needed for manufacturing.

View Complete Details

Ask Latest Price & Details

Tubing

Tubing

Tubing and piping is used to connect components and convey products. ALUMINUM PIPE AND TUBING Alloy 6063 ASTM B-221 6063 T-6 Straights6063 T-1 Bends CARBON-STEEL PIPE AND TUBING Pipe ASTM A-53 This specification covers seamless and welded black and galvanized steel pipeTube ASTM A-513 This specification covers electric-resistance welded-carbon and alloy steel tubing for use as mechanical tubing STAINLESS-STEEL PIPE AND TUBING Pipe ASTM A-312 This specification covers seamless and welded stainless-steel pipe intended for high temperature and general corrosive service. Twenty-four grades are covered, the most common of which are 304, 316, 304L and 316LTube ASTM A-249 This specification covers stainless-steel tubing for general corrosion resisting and low- or high-temperature service. GALVANIZED PIPE AND TUBING Pipe ASTM A-53 Galvanized coated pipeTube ASTM A-513 Galvanized coated tubeTube ASTM Galvanized tube TUBING WALL THICKNESS16 Gauge (.065" wall)14 Gauge (.083" wall)10 Gauge (.130" wall)11 Gauge (.120" wall)12 Gauge (.109" wall) PIPING WALL THICKNESSSchedule 102 = .1543 to 4 = .1205 to 6 = .1348 = .14810 = .165 Schedule 402 = .1093 = .2164 = .2375 = .2586 = .2808 = .32210 = .365

View Complete Details

Ask Latest Price & Details

Fluidizer Bed

Fluidizer Bed

Series FB

The fluidizing bed is utilized as a flow aid for products that are easily fluidizable and not susceptible to "caking" (i.e., flour, come calcium carbonates, some starches, etc.) STANDARD CONSTRUCTION FEATURES Carbon steel dished head and outlet stubPerforated metal plate with two (2) annular support rings to support diffuser cloth5 Ply, 316 thick, diffuser cloth1 Drain with plug OPTIONAL FEATURES Stainless steel outlet stubStainless steel dished head and outlet stubPressure blower package to provide fluidization airMounting hardware and sealantIndustrialFood grade epoxy interior

View Complete Details

Ask Latest Price & Details

FB Fluidizer Bed

FB Fluidizer Bed

The fluidizing bed is utilized as a flow aid for products that are easily fluidizable and not susceptible to "caking" (i.e., flour, come calcium carbonates, some starches, etc.) STANDARD CONSTRUCTION FEATURES Carbon steel dished head and outlet stubPerforated metal plate with two (2) annular support rings to support diffuser cloth5 Ply, 316 thick, diffuser cloth1 Drain with plug OPTIONAL FEATURES Stainless steel outlet stubStainless steel dished head and outlet stubPressure blower package to provide fluidization airMounting hardware and sealantIndustrialFood grade epoxy interior

View Complete Details

Ask Latest Price & Details

Pressure Blower Package

Pressure Blower Package

The Pressure Blower Package utilizes positive air pressure to convey the material. The motive airpressure is produced by a positive displacement blower which is located at the beginning of the conveying system. Air intake filtersilencer - optional air intake filterPositive displacement blower - all major brands availableV-belt drive assembly and drive guard - drive guards feature access via bolted removable doors, slotted front and drop through bottomElectric motor and adjustable mount base - 230460 V, 3 Ph, 60 Hz; all major brands, enclosures and efficiency ratings availableWeighted pressure relief valve provides superior life compared to conventional spring loaded relief valvesCheck valve prevents product from entering discharge silencer in the event of a high pressure or back pressureCombination chamber - absorption discharge silencer reduces noise radiation in the vicinity of the packageVibration isolation and expansion joint isolates blower from the silencer to prevent fatigue stresses to the silencer and piping

View Complete Details

Ask Latest Price & Details

Bulk Bag Fill Head

Bulk Bag Fill Head

Series BBFH

This Fill Head is utilized to assist in filling bulk bags by providing an inflatable seal to secure and seal the spout of the bulk bag. STANDARD CONSTRUCTION FEATURES 8 Inlet flange with ANSI bolt patternDesign to match a 14 16 diameter maximum bulk bag fill spout (Buyer to advise actual size)Heavy duty rubber air bladder sleeveFactory mounted manual air control valve and regulatorTwo (2) Model Number F-235P-300 Air Intake Filter8.3 Square feet of cloth areaDesigned for a maximum of 300 cfm3 Flanged line connectionCarbon steel weather hood OPTIONAL FEATURES Carbon steel or stainless steel product contact surfacesSupport stand with adjustable bag support arms constructed of 4, carbon steel, square tubing with adjustable bulk bag support armsVarying baginlet dimensions

View Complete Details

Ask Latest Price & Details

Pneumatic Tube Railcar Unloading Components

Pneumatic Tube Railcar Unloading Components

These assorted products use pneumatics to move product from railcars and into convey systems including adaptors, filters and hatch vents for rail cars.

View Complete Details

Ask Latest Price & Details

Scale Hopper

Scale Hopper

Series SH

This hopper aids in metering and weighing product and typically is used when the hopper is being pneumatically filled via a Hopper Fill Valve. STANDARD CONSTRUCTION FEATURES Utilized when the hopper is being pneumatically filled via a HopperScale Fill Valve60 Degree hopper with flanged product dischargeClosed top with flanged inletMechanical vacuum breaker valve with vent sock to allow the hopper to breathe air in during the discharge cycleOne (1) half couplings for mounting of high level indicatorThree (3) support lugsLifting lugs

View Complete Details

Ask Latest Price & Details

BBFH Bulk Bag Fill Head

BBFH Bulk Bag Fill Head

diameter 14“ – 16”
Model Number F-235P-300

This Fill Head is utilized to assist in filling bulk bags by providing an inflatable seal to secure and seal the spout of the bulk bag. STANDARD CONSTRUCTION FEATURES 8 Inlet flange with ANSI bolt patternDesign to match a 14 16 diameter maximum bulk bag fill spout (Buyer to advise actual size)Heavy duty rubber air bladder sleeveFactory mounted manual air control valve and regulatorTwo (2) Model Number F-235P-300 Air Intake Filter8.3 Square feet of cloth areaDesigned for a maximum of 300 cfm3 Flanged line connectionCarbon steel weather hood

View Complete Details

Ask Latest Price & Details

desiccant dehumidifier

Desiccant Dehumidifier

MINIPAC DEHUMIDIFIER The MIniPAC dehumidifier is the ideal dehumidification solution for smaller facilities in need of reliable humidity control or mold and mildew protection. The MIniPAC can be installed as a stand-alone unit, or attached to any central air conditioning system to enhance the system's dehumidification capability. A small, yet powerful unit that combats the effects of moisture in a wide variety of applications. Compact off the shelf sizes from 100 to 600 CFM. Suitable for continuous operationAutoManual selector switchPower on, heater on and fault status indicationIndependent blower for each air streamVolume control dampers VFB DEHUMIDIFIER Custom engineered units with sizes from 300 to 30, 000 CFM. The VFB is the ideal dehumidification solution for facilities in need of custom built reliable temperature and humidity control. Electric, stream, direct or indirect fired gas reactivationEasy to remove desiccant rotorCleanable or disposable 30% inlet air filtersRelay-based controls for simple reliable operationHinged filter access doors with quick release fastenersCircuit breakers (not fuses) for over-current protection

View Complete Details

Ask Latest Price & Details

Scaling System Weight Controller

Scaling System Weight Controller

Series HI 2151/30

This weight controller is connected to load cells and montors the weight of the product in bins, receivers, or other containers. This can be used in batching and loss-in-weight applications. STANDARD CONSTRUCTION FEATURES Six digit, fourteen segment LED displayWaterproof keyboard and weight display, NEMA 4 enclosureIntegrated Technician provides built-in system diagnosticsDisplayed resolution, 1:985, 000Update rate of 20 readings in 1 unit incrementsSliding averaging of up to 200 readings in 1 unit incrementsWaversaver feature is adjustableGross or net modes of operationMenu driven digital calibrationFront panel diagnosticsAuto zero trackingMotion detectionSelectable RS-232C, 422 or 485 portTwo relay contact set points (SPDT, 3 amp, 115 VAC)NBS certified (10, 000 counts)Secure memory moduleRemote functions connector115 VAC, 5060 Hz operation OPTIONAL FEATURES Panel or wall mountOutput options Analog, Binary Coded Decimal, Remote IO (RIO) Interface to the Allen-Bradley Network, PROFIBUS Interface, Dynamic Data Exchange (DDE)Control options Peak Hold, Rate-Of-ChangeSet Point Options - TTL(Transistor - Transistor Logic) Level Output , External Setpoint Relays Card240 VAC 5060 Hz Input VoltageNISTNTEP Certification Mode Kit (-E3 except for -F4 wall mount)Portable Display and Keypad (-E4)Intrinsic Barrier Assembly

View Complete Details

Ask Latest Price & Details

Ceram-Back Elbows

Ceram-Back Elbows

Ceramic coated elbows are used for instances where large particle impact or abrasion is a problem during turns or diversions in product lines.

View Complete Details

Ask Latest Price & Details

View More

Tell Us What are you looking for? Will call you back

Contact Us

(Horizon Systems, Inc.)
Lawrence, KS 66046 map, United States
Share us via

View Contact No.