Post Buy Requirement
IP
United States
Add Review

Our Products

  1. Conveyors 7 Products available
  2. Zippers 4 Products available
  3. Gearbox & Gear Parts 4 Products available
  4. Electrical Conduits & Fittings 3 Products available
  5. Others 46 Products available

Other Products / Services

Horton Bark Press Mat

Shown here is a cast Manganese Steel Bark Press Mat.

Each casting is precision broached and faced to create the exact opening size between the links.

This tight requirement is necessary to allow for the release of water while retaining the desired bark.
View Complete Details

Hog Fuel Distribution

  • SERIES H730
A double strand of I'ANCO cast alloy H730 Mill Chain complete with A22 attachments used in a hog fuel distribution conveyor.

A53 swivel attachments complement this chain by allowing the UHMW flights to 'float' between the two strands of chain.

The swivel action of the the A53 reduces applied stress loads on the chain when the conveyor is unevenly loaded or misaligned, and thus provides extended chain life with reduced maintenance cost.
View Complete Details

Rail Car Wood Chip Dump

  • Size 1-1/2 x 2-1/4 x 8"
  • Series 400
At this pulp mill, an automated wood chip receiving rail car dump conveyor operates with 2 strands of Long Link Chain and handles 2 rail cars simultaneously for a load of 120 tons.

A double strand of I'ANCO cast alloy square profile 1-12 x 2-14 x 8" Long Link Chain, complete with 36" wide, Series 400 dual tang flights, takes only 8 minutes to cycle the conveyor clean of wood chips.
View Complete Details

Submerged Ash Tail Assembly

  • Diameter 14 x 50mm
I'ANCO double strand tail shaft assembly for 14 x 50mm round link Drag Chain is used extensively in submerged ash conveyors.

The Tail Idlers are precision machined from quench and tempered material to suit 14mm link chain and are specifically designed to be resistant to the abrasive nature of boiler ash.
View Complete Details

Coal Handling Attachment

  • Series A53
Cast alloy A53 swivel attachment to suit a drop forged 998 rivetless chain. The attachment and the extruded plastic flight are used in an infeed conveyor for a coal fired power generation station.

At 13 of the original weight, this flight attachment replaces a cumbersome one-piece fabricated steel flight that was difficult to replace due to restricted space.

The swivel design eliminates chain stress found in double strand conveyors when one side elongates further than the other. The bolt on system of flights and attachments also eliminates the need for any welding, thus creating a safer and quicker change-out for the facility.
View Complete Details

Bucket Elevator

  • SERIES H132
I'ANCO cast alloy H132 Mill Chain complete with K2 attachments and buckets installed on every second pitch.

This system conveys five hundred tones of asphalt daily from the dryer to the hopper. Here the material ranges in temperature from 150 to 300 degrees Celsius.
View Complete Details

Drag Chain Idler Wheel

  • diameter 557mm , 260mm
Drag Chain Idler Wheel
I'ANCO 557mm diameter Idler Wheel for 260mm Drag Chain shown here with weight reducing cut-outs.
View Complete Details

Cast Alloy Steel

  • SERIES H111
The H111 chain shown in this photo replaced a problematic C111 combination chain.

The C111 side bars were bending and causing the chains to interfere with each other.

By changing to the tougher I'ANCO chain, the bending problem was eliminated and the chains now run smoothly in the trough.
View Complete Details

Receiving Hopper Shaft Assemblies

  • Size 1-1/2"
  • Series HD480
These shaft assemblies are destined for a Hog Fuel receiving hopper system.

There are 2 side-by-side hoppers with 7 strands of HD480 drag chain.

These assemblies use I'ANCO cast Alloy 2A full face sprocket and idler rims mounted on 1-12" wall, seamless mechanical tubing.
View Complete Details

Wood Chip Truck Dump

  • Series HD480
A pulp mill truck dump employing 6 strands of I'ANCO cast alloy HD480 Drag Chain with wing attachments.

The conveyor feeds wood chips, brought in by truck transportation, directly into the pulp mill.
View Complete Details

Reclaimer Stacker Conveyor

  • SERIES H106
I'ANCO cast alloy H106 Mill Chain was supplied complete with extra wear shoes and a cast integral post for this reclaimerstacker conveyor.

The two strands of chain, joined by a fabricated steel bucket through the treaded post attachment, drag chips from outside piles into belts that feed the pulp mill operation.

Due to the excessive weight of the buckets, cast integral wear shoes were added to the attachment links to provide larger bearing surfaces and extend chain life.
View Complete Details

Scraper Link

  • Series 142HVY
The 142HVY Scraper flights shown in this photo demonstrate the hard-facing that can be applied to the leading edge of the scraper.

A bead of hard-facing is applied to the flight and then ground to a plow like edge.
View Complete Details

Flight Attachments

  • Size 22"
  • Series H106
This H106 conveyor chain is destined for a bulk material handling conveyor in a Pot Ash processing plant.

The beveled front on the flight acts like a plow and keeps the material from building up on the bottom of the conveyor.
View Complete Details

Manganese Long Link Chain

  • Series 400
  • Size 1-1/8 x 2 x 6"
I'ANCO cast manganese 1-18 x 2 x 6" square profile Long Link Chain, complete with I'ANCO Series 400 dual tang flight.

This application is a wood waste conveyor feeding a holding silo for disposal.

The chain shown here has been in service since 1995 and is still going strong.
View Complete Details

Shredder Rotor

  • Size 42 x 48"
This 42 x 48" heavy duty Rotor was designed and built by I'ANCO to replace a standard Jeffrey rotor.

The hammers were doubled in thickness so as to increase the pulverization effect on larger stock sizes and keep the material flow rate at its maximum level.
View Complete Details

Shredder Tip

I'ANCO cast alloy Shredder Tips and Holders for horizontal rotors.

The hammer tips are cast in I'ANCO Alloy 3A which provides a typical hardness of 444 BHN.
View Complete Details

Style Manganese Steel Liner

This cast austenitic manganese steel 'Z' Liner is installed in a hog fuel conveyor.

The work hardening properties and low coefficient of friction of the manganese steel makes it an ideal material for liner applications.

This system was specifically designed as a bolt-in wear part for ease of replacement in the future.
View Complete Details

Bolt-In Trough Liner

  • Thickness 3/8"
These bolt-in Trough Liners are formed from 38" thick CHT360 hardened plate.

Threaded studs are welded to the underside of the plate to secure the Liner in the conveyor.
View Complete Details

Sinter Screen

This Vibrating Sinter Screen casting is produced in high temperature stainless steel and is used in a sintering plant for the charge material at a steel mill.

The slots are tapered from top to bottom to allow dust to escape and air to be blown in.
View Complete Details

Cast Liner

Cast Austenitic Manganese Steel Wear Liners servicing a pulp mill in Chile.

These Liners are paired with I'ANCO cast H132 chain of the same material to provide an extended service life.
View Complete Details

Marietta Track Pads

This load of track pads is destined for a Canadian underground Pot Ash mine.

The castings are produced in Low Alloy Steel then quenched and tempered to stringent material specifications.

Each casting is line bored, fitted with a hardened machine pin, then assembled to ensure accurate interface and articulation between the pads.
View Complete Details

Goodman Track Pads

Cast in I'ANCO MT100 alloy steel, these Track Pads provide optimum performance in the harsh operating conditions of an underground Pot Ash mine.

The hardened material provide Points that last the life of the pad.
View Complete Details

Track Pad

Cast steel alloy Crawler Track Pads for Marrietta 780-AW4 tunneling machines that are used for underground mining operations in the potash industry.

The Track Pads are 326 lbs each and are assembled with case hardened pins at I'ANCO's manufacturing facility.

I'ANCO worked with the end user to develop a unique cast material as a solution to the premature failures that they were previously experiencing.
View Complete Details

Port Rodder Tips

Consumable Port Rodder Tips for Anthony Ross Style Machines.

Cast in high temperature, heat resistant stainless steel, the Tips are used to clean boiler window openings to ensure proper air flow.
View Complete Details

Impressifiner Bar

I'ANCO produces both Straining and Breaker Impressifiner Bars in Cobalt Alloy 6 and CB7Cu-1 material for CTMP screw presses.

These bars are investment cast to near net shape, then precision ground to the exact gap and taper tolerances.

I'ANCO also offers the complete re-build service for the Cages including cleaning, liquid die penetrant inspection, all weld up-grades, machining, installation of the bars and final inspection.
View Complete Details

Energy Grates

These Energy Grates, for a traveling boiler grate system, rotate in alternating clockwise and counterclockwise direction to distribute ash from the power boiler.

The tool steel casting has eliminated fatigue failures found in the original parts and provides a higher hardness for extended, maintenance free service.

To date, no failures have been discovered since 2003.
View Complete Details

Chip Thickness Screen Roll

This Chip Thickness Screen Roll has been re-built using extended life tips.

After two years of service the working points of the stainless steel disks still have their original square edges.
View Complete Details

Sawdust Screen Roll

Tasked with a customer request to create a longer lasting Roll, the I'ANCO engineering group replaced the existing cast iron material with I'ANCO cast Alloy 2AQT380.

The life of the rolls improved from 6 months to well over 3 years.
View Complete Details

Window Support Arms

The cast ductile iron Arms were supplied for a renovation of a Downtown Vancouver office building.

The Arms were supplied with a primer coat of paint, ready for assembly onto the main beam.
View Complete Details

Olympic Oval Roof Support Castings

These casting were produced for the general contractor building the Richmond Olympic Oval.

Both the top and bottom anchor assemblies were cast in low alloy steel and fully machined and primed before final installation at the construction site.
View Complete Details

Hot Lime Chute Liner

The Liner for this chute is cast in HN stainless steel and designed to handle the 2, 000 degree Fahrenheit lime.
View Complete Details

Lime Kiln Trunnion Roller

  • Weight 5, 000 lb
This 5, 000 lb Trunnion Roller is used on a Lime Kiln at a Pulp Mill in British Columbia.

The shaft is installed with a FN2 shrink fit.
View Complete Details

Hydraulic Take-up Frames

These fabricated Take-up Frames were designed to suit a customer request for an automatic take-up system on their hog fuel distribution conveyor.
View Complete Details

Plate Attachments

Plate Attachments for both single and double bolt shackles are supplied in materials ranging from mild steel to 316L depending on the application.

The bolts can be supplied with a step in them to avoid over tightening on the shackle or with spacers to ensure the correct torque is applied.
View Complete Details

Solid Swing Hammers

Cast in I'ANCO Alloy 3A, these Hammers have been quenched and tempered to a hardness of 420-460 BHN.

This high hardness material has been engineered with excellent impact resistance to withstand the abuse caused by tramp metal or rocks in the material flow.
View Complete Details

Manganese Swing Hammer

This cast Austenitic Manganese Steel Swing Hammer is used in a gypsum crusher.

The work hardening characteristics of Manganese Steel make this material a popular choice for high impact applications.
View Complete Details

Black Liquor Nozzle

I'ANCO cast 17-4 precipitation hardened stainless steel Nozzle for pulp mill black liquor.

The Nozzle resides inside the boiler and sprays liquor off the bottom splash plate to be consumed by the burner.

I'ANCO assisted in redesigning the previously fabricated nozzle to include a cast integral elbow that minimizes the number of threaded joints and extends the life span from 2-3 months to 6-8 months with the new cast design.
View Complete Details

Pipe Cross

Pipe Cross for a batch digester in a pulp and paper mill.

Cast in austenitic CF8M stainless steel, the pipe is supplied with material certification, both chemical and mechanical, as well as 600 psi pressure test certification.
View Complete Details

Stainless Steel Steaming Elbow

  • SERIES 317L
I'ANCO cast 317L stainless steel Steaming Elbow complete with 6" bottom inlet and raised head flanges.

Flanges are machined to suit 150 psi pipe flanges and the entire unit is pressure tested prior to delivery.

I'ANCO offers both chemical and mechanical foundry certifications as well as NDT reports, as specified for all castings.
View Complete Details

Cast Agitator Hub

  • Model 2205
I'ANCO cast super duplex 2205 stainless steel Agitator Hub for caustic liquor tanks.

The Hub is precision machined, to suit the liquor tank shaft, and fitted with bolt-on 2205 stainless steel blades.

The cast 2205 material is an improvement upon the standard fabricated 316 SS due to it's increased resistance to both erosion and corrosion in this application.
View Complete Details

Super Heater Tube Clips

These Clips are used to hold boiler tubes in place while allowing for heat expansion of the tubes.

They are cast in high temperature stainless stainless steel and come with the weld preps already provided for quick installation.
View Complete Details

Custom Made Lag Bolts

The cast stainless steel Lag Bolts were created for an architectural design firm's new roofing installation at a University expansion project.

The design company provided the conceptual shape and I'ANCO completed the design to allow for an economical production process.
View Complete Details

Stainless Steel Felt Roll Holder

This Felt Roll Holder uses a cast stainless steel 'U' shaped insert welded to a fabricated carbon steel frame work.

This material change was required to combat a corrosion problem encountered in the pulp forming end of the mill.
View Complete Details

Flanged Carrying Rollers

These Carrying Rollers are for a manganese Apron Feeder.

The rolls are cast in manganese steel then mounted in a cast alloy steel support bracket.
View Complete Details

Attachments

I'ANCO offers a wide variety of industry standard cast weld-on, cast integral, or fabricated attachments for the H & C Class chains. The photos show some typical examples of chain attachments in various applications.

In addition to standard attachments, I'ANCO routinely develops unique attachment solutions for customer's particular conveying needs.
View Complete Details

Hot Lime Bucket Elevator

  • SERIES H132
I'ANCO cast alloy H132 Mill Chain complete with cast integral K2 attachments for a hot lime bucket elevator.

Continuous style fabricated steel buckets were supplied preassembled on the chain for quick installation.

Both a 13-tooth and 10-tooth, cast alloy segmented bolt-on sprocket were also provided with this project.

This chain ran maintenance free for 8 years allowing it to be changed out much later than originally planned.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (IANCO Products Ltd.)
  • Surrey, BC V4N3N6 map, United States
  • Share us via