Our Products #4817673

Stop It Flat Patch is a leak sealant product designed for applications where localized repair is needed or full pipe wraps are impractical. The carbon fiber composite repair system quickly restores operations for storage tanks, floating lids, vessels and large-diameter pipes operating at pressures up to 1, 000 psi, and provides localized corrosion inhibition. Stop It Flat Patch surface preparation consists of removing any loose scale and lubricants or greases. The surface should be relieved of all pressure until the product is fully applied and cured. Application surfaces should be dried prior to application and warmed if the pipe surface is less than 50F or cooled if greater than 100F.Application entails mixing a pre-measured two-part sealant, wetting felt and fibrous reinforcement tape, and applying the fabrics onto the surface. Applications can be made regardless of surface orientation and result in a durable coating with superior pressure-sealing capabilities.Sealant mixing takes seconds and can be immediately applied to the reinforcement tape. The wetted tape possesses a working time of approximately 8-10 minutes. The exact application time will depend on the specific conditions under which Stop It FP is being applied.

Our adhesion promoter is a two-part acrylic-based adhesive (1:1 ratio by volume) that can bond many low surface energy plastics, including many grades of polypropylene, polyethylene, and TPOs without special surface preparation. It enhances the bond between Stop It's resin and plastic or fiberglass pipes and will be required for applications involving these substrates. Features:Ability to bond dissimilar substratesAbility to structurally bond polyolefinsRoom temperature cureExcellent water and humidity resistanceVery good chemical resistanceOne-step Process - no pre-treatment of the polyolefin substrates neededSolvent-free adhesive systemConvenient hand-held applicator systemAvailable in Bulk

The Viscotaq line of corrosion-prevention coatings was developed with leading oil and gas and polymer engineering companies to be the ultimate solution for corrosion control a solution that keeps your infrastructure corrosion free for up to 40 years. The unique chemistry of Viscotaq gives it permanent wetting characteristics, allowing the material to flow into the pores and anomalies of the substrate. Its viscous elasticity gives it the strength and feel of a solid but the characteristics of a liquid it wont crack like a solid or run or sag like a liquid. Rather, it remains in a semi-solid state that provides high-impact strength and high resistance against sheering. Viscotaq products stop corrosion in its tracks, and as the pipe shrinks or expands, it will conform to the pipe changes without cracking. ViscoWrap-ST is a non-shielding coating wrap that can be applied without primers, forming a homologue layer after application. It doesnt show sliding, dripping or thickness changes since its a solid with a true melting point of around 150F.

Stop It is used to stop leaks in metal or plastic pipe, reinforce joints and form an anti-corrosion coating. Stop It is a fiberglass tape coated with polyurethane resins that are activated by immersion in water. Once activated, Stop It will transform from a wet adhesive tape to a hard, machinable urethane plastic. Included in each container of the Stop It Pipe Repair System is a plug of Fix Stix epoxy to plug leaks or cracks or to provide a smooth transition at offsets.

When high-pressure pipes leak, the seepage can affect the environment, production and your companys bottom line. Fixing it quickly and securely is a must and reinforcing the pipe walls so that it never gets to that point can save the facility significant time and money later. With Stop It HPTM epoxy leak sealant, you can repair pipeline cracks and leaks and reinforce diminished pipe walls in minutes so that they can handle working pressures up to 2, 000 psi. In as little as four hours, operations can be resumed, and Stop It HPTM exhibits maximum pressure performance after 24 hours of curing. Its the durable solution thats trusted to repair a damaged methane gas line in the inhospitable Dakar, Africa desert. After the fiberglass pipeline was damaged by a motorized grader, Fortesa International used Stop It HP to cover 11 feet of the tube, sealing the five-foot hole and the non-visible damage from fracturing. Surface preparation consists of removing any loose scale and lubricants or greases. The system should be relieved of all pressure until the product is fully applied and cured. Application surfaces should be dried prior to application and warmed if the pipe surface is less than 50F or cooled if greater than 100F.Application entails mixing a pre-measured two-part sealant, wetting a fibrous reinforcement tape, and wrapping the tape onto the pipe surface. Applications can be made regardless of pipe orientation.Sealant mixing takes seconds and can be immediately applied to the reinforcement tape. The wetted tape possesses a working time of approximately 8-10 minutes. The exact application time will depend on the specific conditions under which Stop It HP is being applied.

When a pipe, tank or drum springs a leak, time is of the essence. Thats especially true if it contains hazardous product. Major repairs can take considerable time. Fortunately, InduMar provides emergency repair kits that can plug the holes until major repairs can be made. These kits keep you and your company safe even when pipes, tanks or drums let you down.

Once youve protected your pipeline from corrosion with ViscoWrap and Viscopaste , protect it with the Viscotaq Outerwrap. This heavy-duty outerwrap provides mechanical protection to Viscotaq applications, helping to avoid the damaging effects of backfilling and other stresses so you only have to apply Viscowrap once, saving money and man hours later. UV- and weather-resistantCan be applied within a temperature range of -30F to 185FHas excellent mechanical strengthAvailable in different thicknessesSimple to apply:o Start wrapping under sufficient tensiono Apply with 50% overlapo Apply within application temperatureCan be applied by machine as well

Often times, corrosion starts in hard to reach spaces or on awkwardly shaped items where even a high-quality tape cant effectively cover over the site. Fortunately, Viscopaste is a versatile, easy-to-apply paste that can be applied to hard-to-reach, harder-to-wrap spots to seal the site and keep your tanks and pipes intact for the many years. The Viscopaste comes in 9 coils and measures 1.5 by 1.5. Because of its viscous elastic nature, it can be applied without sagging or running. The unique polymer chemistry retains permanent wetting characteristics, forcing the viscoelastic polymer to flow into the pores and anomalies of the substrate so it has immediate, long-lasting adhesion to steel, PE, PP, epoxy, polyurethane, PVC, and other surfaces. Based upon synthetic polyolefinsHas a melting point above 120CGas restrictiveWatertightHas a very low water vapor permeabilityHas a high chemical resistance (salts, acids, alkaline solutions)

The STOP IT Riser Rehabilitation Kit is intended to strengthen the structural integrityof the riser nipple, or riser casing on non-leaking 34 and 1 standard anodeless risers.It is comprised of a strong knitted fiberglass tape coated with fast setting, water-activatedurethane resins. The STOP IT Riser Rehabilitation Kit also includes FIX STIX, a steelfilled hand moldable epoxy that sets rock hard in only 20 minutes The STOP IT Riser Rehabilitation Kit is a necessary item in an inventory of productsfor minimizing corrosion-related operating costs. Kit Contents: STOP IT knitted fiberglass tape precoated with water-activated polyurethane resinsFIX STIX hand moldable epoxyGloves for easy clean upDetailed directions

Off-the-shelf solutions may not work when youre dealing with a thin, cracked or fractured pipe wall. Sometimes, you need something tailored for your unique situation. Stop It CR-E is a state-of-the-art epoxy-based composite repair system, so your maintenance team wont have to take the time and resources to combine solutions into an ad hoc patch. After talking with your representatives to get the project requirements, InduMar designs an application that meets DOT-governed pipelines and your exact needs. This engineered composite kit consists of a hybrid fabric that employs high-grade E-glass and Kevlar yarns arranged in a multi-axis layout that maximizes the composite strength. Its exceptional toughness resists cracking and can handle temperatures up to 450F. The pre-treated fabric assures the micro-fibers are significantly stronger than an untreated lay-up.The two-part epoxy resin grade is selected for your application type. Custom formulations give our product exceptional properties of flexibility, adhesion, toughness, chemical resistance, thermal resistance, vibration and more. Special grades are available to handle your special situations.Stop It CR-E kits ship to the field with all components pre-measured and factory sealed. Everything is included: composite fabric, two-part epoxy resin, primer, stirring sticks and UV paint. The technician simply lays out a pre-measured reinforcement fiber section, mixes and applies the pre-measured epoxy resin components to the reinforcement. No measuring is required in the field and performance tolerances are tightened with controlled fabricepoxy resin ratios.