Our Products #5216692

FEATURES: 450 lb capacity pressurized reservoir4-zone, heated, stainless steel reservoir cylinderPlaten-mounted Zenith high pressure metering pump34, 000 watt secondary heat exchangerSelf-purging cycle for rapid cleaning product change-overAutomatic air bleed product sampling valveOptional high pressure filtration ( to 10 microns )BENEFITS: Continuous metering of high viscosity adhesives and sealantsProcesses polymers with viscosities up to 2 million cpsStores up to 450 lbs of molten polymer in an air-free, nitrogen-free pressurized state.Pressurized reservoir provides continuous feed of molten polymer to the metering pump up to 3, 200 lbshr.Can be supplied by up to (3) Uniflow drum unloadersNo adhesive bridging nor stagnation within the reservoir cavityNo drum- change flow interruptionSelf-purging feature automatically returns unused polymer back to an empty drum under anaerobic (air- free) conditions. Leaves reservoir wall clean with no polymer residueIdeal for moisture curable urethanes, UV curables and char sensitive polymersDirect extrusion, zero shear, pressure-based metering option is available for low viscosity, UV curable resins.Bottom entry reservoir input manifold is available for heat- history sensitive polymersType 316 stainless steel construction is available for anaerobic metering of UV-curable polymers, resins and compounds

Fitted with a 20-Ton Hydraulic Ram and optional 5 horsepower motor, this drum unloader can pump adhesives and sealants measuring up to 2 million cps @ 300 F. STANDARD SPECIFICATION & FEATURES Overall Size: Width (Control Box face to cross beam junction box)-59 inches (75 inches for 480 VAC Unit) depth 31; height (beam fully raised)-116 inches.Weight: 1, 300 lbs. (empty) (1, 800 lbs. 480 VAC Unit).Air Requirements: (PSI) -80 Min., 150 Max. (Hydraulic RAM Optional.)Air Consumption: Less than 1 SCFM Continuous.Electrical Service: 208230 VAC, 3 ph, STD. (480Vopt.) 5060 HZ, 150200 AMP Entrance.Power Consumption: 135 AMPS at 230 VACTemperature Range: 100 F to 550 F (Depending on Platen Style)Material Flow Rate: Up to 2000 lbs.hr. Depending on hot melt type and Platen Style.Material Viscosity: 100 CPS to 2 Million CPSStart-Up Time: Less than 20 minutes. (From 65F)Total Drum Change Flow Interruption: Less than 5 minutes.

The two drum unloaders alternately pump to the metering pump for continuous operation.A bumpless transfer maintains a constant inlet pressure to the metering pump.

Damaged seal section can be replaced by tapping in repair plug, even with follower platen hot. Multi-piece 0-Ring cord stock held in place by unique self-retaining groove. Complete seal can be replaced in less than 5 minutes (with platen hot or cold).

Similar concept to Model 2035, but it has three (3) Gear Pumps with independent controls.Industry-Specific Favorite: Cable Industry

Model 181 Platen 28 or 34 kw High Output, Finned Platen with the largest heated surface area in the world. Temperature range up to 425F.

Automatically draws the clam shell reinforcing jacket tightly around the fiber drum.Imparts a uniform clamping force along the entire fiber drum wall.Modular construction allows for easy maintenance.Remotely operated by touch screen input.

Drop forged clamps for strength.Eliminates drum splitting by closing around a 22 I.D. fiber drum, giving it steel drum strength.Allows use of fiber drums with minor damage, such as cuts, creases or small punctures.Holds the fiber drum rigidly centered between the two ram cylinders to prevent the follower plate from sliding off center.Enables the use of high Ram Down force to allow the platen fins to penetrate tough, high-viscosity material to deliver a higher output.

Delivers high viscosity liquids, silicone based adhesives and thermally conductive heat sink polymers directly to the dispensing head, without a pump. No motor, no gearbox, no pump, no problems with crosslinking. The unique combination of hydraulic ram and pail reinforcing jacket allows polymer pressurization (at adjustable pressures up to 400 psi) right inside the pail. Product flows directly from the pail into the delivery hose and right to the dispensing valve with no shear.Adjustable ram force for setting polymer pressureOver-night shut-down and restart the next day with no purgingMultiple output hose and valve capability without flow variation (when valves are opening and closing randomly)One to two minute pail change with immediate flow resumption