Products / Services #5141700

Eliminates the need for an expensive edger with polish cycles
Three different cycles to accommodate all materials
Vacuum connection keeps work area clean
Automatic shut-off

UVX Our most economical UV is a 5-8 minute treatment that will treat 150 or more pairs of lenses. Available in 8oz concentrate or handy dry capsules.

60 Second U.V. Inlands best UV in 60 seconds. Great for 1 hour locations or busy labs. Treats approximately 200 pairs of lenses. Available in 8oz concentrate.

U.V. Clear as Glass A 5 minute UV that gives the lens the appearance of a piece of glass. Treats approximately 200 pair of lenses. Available in 8oz concentrate.

All Clear All Clear basic neutralizer is used for CR39. Faster than all inclusive neutralizers.

Ultra Clear Ultra Clear is a neutralizer that can be used on all materials. It is gentle enough for Poly and High Index, but strong enough to be effective on CR39 as well. Economical to use.

Poly Klear Poly Klear is a premium neutralizer designed specifically with Poly and High Index materials in mind. It can also be used on CR39.

HC Clear+ Our very best neutralizer. It is safe, fast and effective on all lens materials. It can also be used as a pre-soak for tinting. HC Clear+ is a concentrate, saving shipping costs and shelf space.

All Coolants that contain anti-foaming agents contribute to bacterial growth, therefore shelf life is reduced. These should also be changed immediately if they have an offensive odor.

Chill Out Chill Out concentrated coolant. Recommended usage is 6oz to 5 gallons of water. Anti-foaming is built in. The recommended change period is once a week.

Lite Edger Coolant Lite Edger Coolant Premium quality, highly concentrated coolant. Recommended usage is about 2oz to 5 gallons of water, and has no anti-foam properties. Recommended change once a week.

Aqualite Edger Coolant Aqualite Concentrated Coolant to be used in edgers and generators. Anti-foaming agent built in. Recommended usage is 8oz to 5 gallons of water. Change weekly.

CAP COOL Concentrated Powder Coolant CAP-COOL Concentrated Powder Coolant used for edgers and generators. Same lubricity as liquid coolants. Anti-foaming agents built in. Less costly to ship and needs very little shelf space. Recommended usage is 1 capsule to 5 gallons of water. Change weekly.

Now you can eliminate the most troublesome and costly maintenance on your cylinder machines. Bearings and bushings in wobble and wobble bearing assemblies require constant maintenance and frequent replacement until now!

The Otley works on a ball-and-socket assembly. The ball is allowed to roll rather then rub. The two hook shaped flat springs prevent the main shaft from rotating while allowing free movement around the vertical axis. The Otley is a revolutionary patented concept. It has only one moving part, completely eliminating the bearings and bushings from the main shaft and the maintenance and downtime that go along with it.

Ink Remover This is a safe product to be used on any lens material. It can be used even after drilling without the fear of crazing, and will remove safely and effectively, all manufactures ink markings.

Ink Remover Pens- Same as above in a convenient pen form.

Spec Prep Spec Prep is a pre-soak that removes oils and process chemicals from lens to promote even tinting across the lens surface. Spec Prep also helps to reduce spotting and streaking.

Isopropyl Alcohol Isopropyl Alcohol is a 99%pure filtered alcohol used for general cleaning of lenses prior to hard coating.

Tint Units and pans are manufactured from 100% 304 Stainless Steel. The heating element is not in the pan, which eliminates the possiblity of leaks and greatly increases element life. This also allows for the use of water in place of heat transfer fluid.

Your best defense in avoiding slippage with todays most demanding hydroscopic super slippery lens surfaces. All the strength that SecurEdge offers, with the addition of the industries best adheasive, and an effortless release.

Omni Guard 15 Omni Guard 15 is a hot soak, scratch resistant coating. It is generally heated in tint unit to 195-200 degrees F and the lens is soaked in the solution for no more than 15 minutes. The lens is then wiped clean with a soft cloth.

Super Scratch Guard Super Scratch Guard is a cold dip scratch resistant coating. The lens is dipped in the solution for 2-3 seconds, rinsed with cold water and wiped clean with a soft cloth. Super Scratch Guard provides a long lasting coating with very little effort, and without issues with heating sources.

Heat Transfer Fluid Heat Transfer Fluid is a thick medium used to evenly distribute heat in tinting units. The fluid helps to avoid hot and cold spots that can occur when using only water.