Our Products #4964330

Surface-Cleanse930 is a gentle, nonionic cleaner that delivers a powerful cleaning action usually found in much harsher products. Surface-Cleanse930 has a neutral pH, which eliminates surface damage that may be caused by an acid or alkaline cleaner. Its mixture of nonionic surfactants make Surface-Cleanse930 safe for use on aluminum, zinc, electronic components and other delicate metals. Surface-Cleanse930 works well in hard and soft water and at room temperature. Surface Cleanse930 is registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 6.5.

Zymit Low-Foam is a neutral pH, dual-enzyme formula effective at removing protein- and starch- based soils. Zymit Low-Foam is used to clean diagnostic and surgical instruments, medical devices, labware, fabrics, food processing equipment, photographic film equipment, hospital and daycare furnishings, and many other surfaces. Target soils include gelatin-based adhesives, food, grass, blood, fat, sweat, mucous, tissue, feces, sebum, and starches such as polysaccharides.

Zymit Low-Foam is registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 7.5.

Zymit Pro is a biodegradable, neutral-pH cleaner formulated with a unique blend of protease enzymes, surfactants, and builders that work together to remove tough protein-based soils. The enzymes dissolve the soils, and the detergents help lift and wash them away. Target soils include food, gelatin, and biological materials such as blood, fat, and tissue. Zymit Pro is effective for cleaning filter membranes, metals, ceramics, plastics, medical instruments and devices, food processing equipment, and other surfaces.

Zymit Pro is registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 7.5.

P-80 Emulsion for Incidental Food Contact (IFC) is a biodegradable temporary assembly lubricant that eases installation of tight-fitting rubber and plastic parts by reducing the force needed for assembly. Once assembly is complete, the lubricant dries and the part returns to its original condition. P-80 Emulsion IFC can be applied manually or automatically, by dip, brush, or spray techniques. Use P-80 Emulsion IFC in incidental food contact applications when a thin film of lubricant is desired.

P-80 Emulsion IFC Temporary Assembly Lubricant is used to install pump seals, hoses, o-rings, bushings, gaskets, grommets, grips, and many other rubber and plastic parts.

P-80 Emulsion IFC meets FDA regulation 21 CFR 178.3570 and is NSF-Registered as an H1 lubricant.

Typical viscosity of P-80 Emulsion IFC: 150 cps at 25 C

LF2100 is a powerful, low-foaming alkaline cleaner containing a special blend of chelants, nonionic and amphoteric ingredients. Excellent for removing oil, grease, wax, tar, flux and biological debris from manufacturing and food-processing equipment, tanks, instruments, labware, and many other surfaces. The low-foam formulation makes it suitable for use in labwashers, power sprayers and industrial sized washers. Registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 9.7.

Excellent for use on stainless steel, glass, ceramic, plastic, rubber, concrete, and most other hard surfaces.

Micro-90 is a mild, yet powerful, multipurpose, alkaline cleaning concentrate that has long been used in laboratories, industrial applications, and critical cleaning processes. Micro-90 is a unique chelating detergent that contains ionic and non-ionic ingredients, which combine to produce a variety of cleaning actions. Micro-90 lifts, disperses, emulsifies, sequesters, suspends, and decomposes soils, then rinses away leaving the surface absolutely clean. Registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Micro-90 is manufactured in a dedicated system. Typical pH: 9.5.

Micro A07 is a powerful blend of chelating citric acid and anionic surfactants designed to remove salts, soap scum, metal oxides, hard water scale, grease, rust, milkstone, mineral deposits and inorganic material from filter membranes, labware and industrial equipment. Micro A07 is non-corrosive and does not contain solvents, phosphates, silicates, phenols, or Substances of Very High Concern. Registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 3.0.

Micro Green Clean is an industrial-strength, free-rinsing, biodegradable, multi-purpose hard surface cleaner designed for use in a wide range of cleaning applications. Excellent for cleaning metals, ceramics, medical instruments, food-processing equipment, filter membranes, and other surfaces. Micro Green Clean is registered with NSF as an A1 cleaner and can be validated in FDA processes. Validation methods are available upon request. Typical pH: 9.5.

Excellent for use on stainless steel, glass, ceramic, plastic, rubber, concrete, and most other hard surfaces.

P-80 Emulsion Temporary Assembly Lubricant is a biodegradable assembly aid that eases installation of tight-fitting rubber and plastic parts by reducing the force needed for insertion. Once assembly is complete, the lubricant dries and the part returns to its original condition. P-80 Temporary Assembly Lubricants can be applied manually or automatically, by dip, brush, or spray techniques.

P-80 Emulsion Temporary Assembly Lubricant is used to install hoses, o-rings, seals, bushings, gaskets, grommets, grips, and many other rubber and plastic parts. Use P-80 Emulsion when a thin film of lubricant is desired.

Typical viscosity of P-80 Emulsion: 150 cps at 25 C

P-80 Grip-It Quick-drying Temporary Assembly Lubricant eases installation of tight-fitting rubber and plastic parts by reducing the force needed for assembly. Once assembly is complete, P-80 Grip-It dries and provides resistance that helps keeps parts in place. P-80 Grip-It can be applied manually or automatically, by dip, brush, or spray techniques.

P-80 Grip-It is ideal for insertion of hoses that are pressure-tested immediately after assembly, and in any application that requires a fast-drying lubricant. Typical uses include installation of hoses, grips, o-rings, seals, bushings, gaskets, grommets, and many other rubber and plastic parts.