Post Buy Requirement
LH
United States
Add Review

Other Products / Services

Little Blaster

The LITTLE-BLASTER equipment was designed for the hobbyist or very light production use. The LITTLE-BLASTER is constructed from heavy gauge metal, which is continuously welded. Also incorporated into the line are several products from the BLAST-IT-ALL production blasting equipment, proven reliability such as the blast gun. The LITTLE-BLASTER is also designed for a small company to start blasting with only a dust collector; then, without a lot of expense enables that user to convert to a reclamation system with the LITTLE-BLASTER Reclaimer Kit.
View Complete Details

ABC Shot Peeners

  • Model Number ABC 3636P
  • Dimensions 36″ W X 36″ D X 30″ H
Cabinet Construction:
12 Gauge Reinforced Continuously Welded
Durable Enamel
Primed And Painted. Corrosion Resistant
Dimensions: 36 W X 36 D X 30 H
Safety Door Interlocks
Self Adjusting Door Latches
Full Length Hinges
Lighting:
Two Tube, 24 Fluorescent Fixture
Low Temperature
Shielded, Externally Located
120 V, 60 Hz
View Complete Details

Cartridge Collectors

The M series collectors are of cartridge type with auto cleaning and are designed and built for continuous duty operation. The units are designed for use with abrasive blast systems.
Air Flow: M-2 400 & 700 CFM & M-4 900 CFM
M-2: Approximately 36 L x 18 W x 90 H with legs for 5 gallon dust drum
M-4: Approximately 47 L x 36 W x 90 H with legs for 5 gallon dust drum
Construction: Standard construction of the unit is 11 gauge hot rolled steel, reinforced to maintain structural integrity to 15 W.G. All wiring, air piping, solenoids and valves are mounted externally. Inlet sizes 6 through 8.
Filter Cartridges: Filters are replaceable cartridges. Each filter has approximately 103 square ft of filter media. PN: (011519).
Number of Cartridges: This collector is fitted with two filter cartridges. Cartridges are changed from the outside of the unit.
View Complete Details

Clean Bench

  • Table Size Front To Back (30″), Across Front (48″)
**Keep your work environment clean with this self contained clean bench. Clean parts inside cabinet without getting dust and debris on shop floor. **
Model:
Model CB4830-2, 14 Gauge Steel
Overall Dimensions:
Front To Back (30), Across The Front (74), Height 78
Table Size:
Front To Back (30), Across Front (48)
Down Draft Opening:
24 X 24 Centered On Table, With #9, Expanded Metal.
Blower:
1 Hp, TEFC, 115 Volts, 60 Hz. (or As Model Number)
Dust Collector:
Single 13 X 36 Filter Cartridge, 240 Sq Ft Of Pleated, 8020 Blend Of Filter Material With Bottom Dust Containment Drawer.
Exhaust Silencer:
The Exhaust Area Lined With Sound Abatement Material.
View Complete Details

Paint Bench

  • Table Size 30
** Keep your work environment clean with this self contained paint bench protect your shop walls and floor from paint over-spray.**
Model:
Model Paint Bench, 14 Gauge Galvanized Steel
Overall Dimensions:
Front To Back (30), Across The Front (74)
Table Size:
Front To Back (30), Across Front (48)
Fan:
13 Hp, 115 Volts, 60 Hz. (hazardous Location)
Filters:
Two (2) Replaceable, Fiberglass Filters
View Complete Details

Portable CO Airline Monitor

This portable airline monitor connects easily to a compressed breathing air source and monitors the air for CO content.
The audible alarm (90 dbA) will activate when the CO level exceeds 10ppm (5ppm International). External alarm and lights allow for the unit to be used in the closed position.
Specifications:
Operates on 9-volt batteries andor 115 VAC
Connector Kit Includes 14 Hansen coupling supplied on 5ft. hose
Standard alarm jack allows for connection to remote alarm devices
Handles air pressure up to 120psi
Available in high pressure version up to 5000psi
Optional high intensity alarm
Available in approved Intrinsically safe version 9 VDC only
View Complete Details

Grind Booth

**Keep Your Work Environment Clean With This Self Contained Grind Booth. Protects Your Shop Floor From Dust, Metal Shavings, Or Other Debris That Could Cause A Safety Hazard.**
View Complete Details

Strip-N-Vac

Hi Static Vacuum Recovery
120 Volt Electrical Service
25 Ft. Vacuum Recovery Hose
Non Clog Pick Up Wand
Pulse Jet Cartridge Cleaning
Magnehelic Gauge Filter Monitor
Quick Recovery
Debris Screen
10 Cu. Ft. Storage Hopper
Deadman Controls
Adjustable Media Flow Valve
25 Ft. Blast Hose With 5 16 Carbide Nozzle
90 CFM @ 60 Psi Required 25 Hp (5 16 Nozzle)
View Complete Details

Ergonomic Cabinets

  • Model 4836-E
Fluorescent Lighting With Tempered Glass Protector
Snap-in (Quick Change) Cloth Lined Gloves
Safety Tempered Glass Viewing Window
Quick Change Window Frame
Mylar Window Protector
All Pneumatic Blast & Safety Controls
Adjustable Door Latch
Double Lined Door Panels
Two Full Size Opening Doors
Cabinet Constructed Of 14 Gauge Steel
Dust Blow-off Nozzle
Pressure Cabinets (Top Hose Entry)
Easy Service Pneumatic Controls
View Complete Details

Soda Blaster Pot

1.7 Or 2.5 Cu Ft Bi-carbonate Of Soda Pressure Pot
With After Cooler And Filter
Electric Dead Man Control
50 Ft Of 34 Coupled Blast Hose
14 Nozzle
View Complete Details

Plastic Media System

Blower:
7 12 Hp TEFC Motor, 230460 V, 3PH
Direct Drive
Rated At 900 CFM @ 20 WC
Dust Collector:
900 CFM Rated
(2) Cartridge Filters
Auto Pulse Jet Cartridge Cleaning
Dust Collector Sump
Slide Gate For Dust Removal
Easy Access Door For Cartridge Replacement
Cabinet Constructed Of High Quality 7 Ga. Steel
View Complete Details

EB Vibratory Finishers

1. All Specifications Subject to Change Without Notice.
2. SW (Straight Wall), CW (Curved Wall)
3. Steel Media Machines Quoted Upon Request.
4. Single Phase Power Available on Certain Models.
5. Special sizes and bowl configurations available. Call for details.
6. Working Capacity = Total usable volume in work chamber.
View Complete Details

Magnum

  • Size 44″ and 55″ wide
Available in larger sizes (44 and 55 wide) than our Little Blaster series, our Magnum series blast cabinets are offered in suction or pressure models. The Magnum incorporates many of the same features found in our little blaster line and are suitable for either shop or industrial applications. The Magnum uses our more powerful 400 or 600 cfm reclaimers to insure good media is separated from dust.
View Complete Details

Level Cabinet

  • Model SL5248P
The Select-A-Level cabinet allows the operator to go from a sit down operation to a stand up level suited to the individual operators height. The cabinet has an extra large viewing window, padded arm rest, and movable foot blast control. The foot blast control can be converted to other types to aid handicap operators. The lighting is greater than 200 foot candles, for better visibility. When a HEPA filter is incorporated into the dust collector exhaust the sound level, at the operators station, is less than 72 decibels. By simply pressing either the up or down button the machine can be electrical raised or lowered to suit the operators best comfort position. SNAP-IN gloves are used so each operator can easily change out the gloves, from outside the cabinet. A roll of mylar is positioned next the viewing window and rolls under the glass to protect the viewing window from abrasion. The machine is equipped with safety door interlocks, so if one of the doors is opened, the blasting will stop.
View Complete Details

Barricade CO Monitor

Ensuring the quality of air supplying your respirator is made simple with the Barricade Carbon Monoxide (CO) Monitor.
The Barricade will detect Carbon Monoxide levels less than 1 part per million (PPM) and alerts you with a 105-decibel audible alarm and visual indicator when it exceeds the allowable level. The Barricade is equipped with an easy-view LCD screen that displays the amount of CO present in the air. The unit can be powered with 12 Volt DC or 120 Volt AC. If you are working far from the unit, up to 250 feet, utilize the optional remote Strobe and Alarm.
The unique Alarm Silencer allows for temporary quieting of the audible alarm for up to 4 minutes. This gives you time to investigate the source of the CO but never disconnects power to the instrument.
View Complete Details

Water Blaster

1. Portable Heavy Structural Frame With Fork Lift Points
2. Main Containment Fabricated With 304 Stainless Steel
3. Two Fold Down Operator Platforms
4. Dual Filtration With Felt Filter Bags
5. Three (3) Low Pressure Pumps
Wash Pit To #1 Filter Containment Drum
#1 Drum To #2 Filter Containment Drum
From #2 Drum, Filtered Water For Rinse
6. 700 Psi High Pressure Cleaning Pump With Hand Held Nozzle
7. Fresh Water Tank For High Pressure Cleaning
8. GFI Electrical Protection
9. Individual Pump Switches With Pilot Light Indicators
10. Treated 4 X 4 Support Runners
11. Polyethylene Strip Protectors
12. Rear Work Door Positive Latch
13. PVC & Brass Valves For Controls And Draining
View Complete Details

Barrel Blaster

  • Model Number D10
Constructed of high quality 12 gauge steel.
Constructed of 11 gauge steel. Access to parts loading and unloading is through a removable door, held in place by cam type clamps for security.
Cabinet Door:
One, full opening, swing type mounted on heavy duty hinges.
View Complete Details

Air Tanks

ASME J10B DOT Tanks Air tanks OilAir receivers Dryer Tanks
Custom and Standard Configurations Diameters from 4 to 120 and thickness up to 1.25 Lifting capacity exceeding 10 tons
CNC punching and high definition plasma cutting
Shearing, rolling and press brake capabilities
Robotic welding
Powder painting
View Complete Details

Pull Through Bag Collectors

Blasting by-products are collected in a series of vertically mounted, closed end, dust bags suspended on a spring mounted holder. The dust bags are housed in a metal cabinet constructed of high quality steel, with a corrosion resistant enamel finish. Dust is shaken from the bags by a high frequency vibrator mounted on the bag holder. Standard control of the shaker mechanism is by a manually operated air switch, or by an optional automatic shaker control. Dust removed by the shaking process is deposited in the dust sump. Dust and blasting by-products are easily removed for disposal by a slide valve located at the bottom of the sump.
View Complete Details

Fortress Respiratory Protector

The Fortress Respiratory Protector can process up to 50 CFM of air through a four stage filtration system.
Stage One and Two remove moisture, oil mist and particulates. Stage Three removes odors through an activated charcoal bed and Stage Four converts small amounts of Carbon Monoxide to Carbon Dioxide through patented technology.
A built-in Carbon Monoxide monitor, powered by multiple sources, samples the air for residual CO and will alarm if the volume exceeds allowable levels. The durable, plastic, safety orange enclosure provides portability or mounting capability and protects the components from the elements.
View Complete Details

Clemco Apollo 600 Helmet

The Apollo 60 HPLP is a Type CE continuous-flow, supplied-air respirator for abrasive blasting, to be used with compressed air systems and ambient air pumps. The high visibility red helmet meets ANSI standards for impact protection and OSHA standards for respiratory protection and noise limitations. The Apollo 60s full-helmet design protects the blast operators head from rebounding abrasive and from construction site impact hazards.
The heavy-duty waist-length cape protects the operators neck, shoulders, and chest from rebounding abrasive.
Wide, full-view window
Lightweight construction
Nylon carrying strap
Heavy-duty waist-length cape protects the operators neck, shoulders and chest from rebounding abrasives
Allows operator to wear supplementary hearing & primary eye protection
View Complete Details

Bullard Blasting Respirators

Blast-It-All part number (25-1088) airline respirators provide advanced protection in the harsh exposures of blasting and painting. The snug, yet comfortable, sewn-in neck cuff provides a physical barrier to airborne contaminants and helps maintain positive pressure within the helmet.
Comfortable Fit
A lightweight inner shell with an adjustable headband suspension holds the respirator firmly and comfortably on the wearers head. Airflow is channeled directly to the users breathing zone for easy breathing. The helmet easily accommodates beards, prescription eye wear or safety glasses. No fit testing is required.
View Complete Details

HEPA Filters

HEPA1 Rated Up To 2000 CFM @ 1.5 Sp Drop
Final Filtration 99.97% @ .3 Micron
The HEPA1 can be attached to the outlet of a fan with a flexible connection.
View Complete Details

Bag Collectors

  • Material Cotton Sateen
  • Weight 9.6 Oz Per Sq Yd
Material: Cotton Sateen
Weight: 9.6 Oz Per Sq Yd.
Thread Count: 96 X 60
Air Permeability: 10 to 20 CFM
Construction: All Seams Overlap
Attachment: Screw Type Clamp
(11-415) Dust Bag 300 400 CFM (18 Diameter X 56 Long)
Single Bag Construction
5 Inlet 25 Sq Ft Of Filtration
(11-715) Dust Bag 600 700 CFM (18 Diameter X 70 Long)
Double Bag Construction
6 Inlet 30 Sq Ft Of Filtration
View Complete Details

Batch Curing Ovens

Industrial process ovens for baking, drying, preheating, annealing or any other heat processing of large or numerous parts at temperatures to 500 degrees f. Oven size conveniently accommodates materials handling equipment. Choice of either combination or full horizontal air flow in either rear or top mounted heat chamber configurations. Designed and constructed for long, hard, continuous use.
Two Air Flow Patterns Available:
Combination airflow for random shapes and sizes or for large bulky objects where heated air can move upward, around and through the load. Horizontal air flow for application where heated air must move sideways to pass through a load such as trays or flat sheets.
View Complete Details

Dust Collector

This type collector connects to the outlet side of the reclaim fan by a flexible duct. The inlet of the collector has a damper for balancing the air flow from the reclaim. Blasting by-products are collected in a series of vertically attached cotton sateen dust bags. Dust is shaken from the bags by a manual mounted hand shaker. Dust removed by the shaking process is deposited in a dust drawer at the bottom of the collector.
View Complete Details

Standard Contractor Pot

Each abrasive blasting system features efficient piping designed to provide low pressure drop. For each drop in pressure of just 1 psi at the blast nozzle, a blasting system loses 1 12% in productivity, so minimizing pressure drop is important. The systems are low maintenance for reduced downtime. Theyre designed with a low profile for easier filling and ample wheel clearance for greater stability when the system is in use.
View Complete Details

Trans-Air Pipe

TransAir is a new modular aluminum piping system. This versatile piping system features lightweight materials and push-to-fit connectors that can be installed without threading, welding or sweating. There are no special tools or trades required to install TransAir and the simple to use connecting and mounting hardware will get everything up and running in no time.
TransAir is exceptionally versatile and can be easily integrated into existing systems made from other pipe materials. It can also be modified to accommodate changing needs. The smooth, calibrated aluminum provides the best possible flow, and will not rust or corrode over time. Full bore fittings minimize pressure drop and leak-free connectors prevent costly compressed air loss.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Larry Hess and Associates, Inc.)
  • Salisbury, NC 28145 map, United States
  • Share us via