Our Products #5143893

Enerpac extreme environment cylinders, pumps, and valves are designed to withstand the harshest conditions
Corrosion resistant, nickel-plated valves and cylinders
Stainless steel pump inserts will not corrode
Viton Seals provide heat and chemical resistance
Anodized aluminum pump reservoirs and plastic encapsulated pump bodies resist wet environments
Two-speed operation reduces pump handle strokes 78% compared to single-speed pumps
Pump handles lock for easy carrying.

Enerpac aluminum and steel lifting jacks have a capacity of 7 to 150 tons
All-directional operation on 7, 15 and 35 ton JHA-series
Internal relief valve to prevent overloading
Machined flat front and bottom surfaces permit flush alignment in tight corners
Chrome plated plungers
Pumping handle included
Automatic by-pass port to prevent over-extension (JH-series).

Side Load capability of 4% at full stroke
Extremely low collapsed height
Integrated tilting function up to 4 degrees
Nitrocarbonized surface treatment for harsh conditions
"Red Line" to indicate maximum stroke

Enerpac high tonnage cylinders designed with the lowest collapsed height for use in confined spaces
Overflow port functions as a stroke limiter
Plunger wiper reduces contamination, extending cylinder life
Interchangeable, hardened grooved saddles are standard
Special synthetic coating for improved corrosion resistance and lower friction for smoother operation
CR-400 coupler and dust cap included on all models
Single-acting, load return.

Hydraulic vertical lifting wedge has lifting force of 16 tons at 700 bar hydraulic pressure
Requires very small access gap of only 10 mm
Each step can spread under full load
Straight vertical lifting
Unique interlocking wedge design: no first step bending and risk of slipping out
Single-acting, spring return cylinder
Lifting wedge LW-16 includes safety block SB-2
Includes RC-Series Cylinder with CR-400 coupler.

Enerpac RC Series single acting hydraulic cylinders set the industry standard for general purpose cylinders.
Unique GR2 Bearing Design, reduces wear, extending life
Collar threads, plunger threads and base mounting holes enable easy fixturing (on most models)
Designed for use in all positions
High strength alloy steel for durability
Redesigned cylinder thread protector for ease of use
Heavy-duty, pretensioned spring improves retraction speed
Baked enamel finish for increased corrosion resistance
CR-400 coupler and dust cap included on all models
Plunger wiper reduces contamination, extending cylinder life.

Enerpac single acting aluminum hydraulic cylinders are lightweight by design to provide maximum portability.
Composite bearings prevent metal to metal contact, increasing cylinder life and resistance to side-loads of up to 10%
Hard-Coat finish on all surfaces resists damage and extends cylinder life
Handles standard on all aluminum cylinder models
Steel base plate and saddle for protection against loadinduced damage
Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
High strength return spring for rapid cylinder retraction
CR-400 coupler and dustcap included on all models
All aluminum cylinders meet ASME B-30.1 and ISO 10100 standards

RSM-Series, Flat-Jac Cylinders
Compact hydraulic cylinder wtih a flat design for use where most other cylinders will not fit
Single-acting, spring return
RSM-750, 1000 and 1500 cylinders have handles for easy carrying
Mounting holes permit easy fixturing
Baked enamel finish for increased corrosion resistance
CR-400 coupler and dust cap included on all models1)
Hard chrome plated high quality steel plungers
Grooved plunger ends require no saddle.
RCS-Series, Low Height Cylinders
Lightweight, low profile cylinder design for use in confined spaces
Single-acting, spring return
Baked enamel finish for increased corrosion resistance
Plunger wiper reduces contamination, extending cylinder life
CR-400 coupler and dust cap included on all models
Grooved plunger end with threaded holes for mounting tilt saddles
Integral handle on RCS-1002 for easy carrying
Plated steel plungers.

Climbing jacks include integral tilt saddles with maximum tilt angles up to 5
Large base with anti-rotation rod for stability and safety
Built-in safety valve prevents accidental over-pressurization
Feature to install stroke sensor
Ideal in combination with EVO-Series synchronous lifting pumps
Baked enamel finish for increased corrosion resistance
CR400 couplers included on all models.

Enerpac hydraulic machine lifts are designed for lifting heavy equipment with minimum available access
Remote hydraulic pump enhances safety
Low height lifting toe
Precision guided to reduce friction and isolate cylinder from side-loads
Two extendable support feet provide extra stability
Includes RC-Series DUO Cylinder with CR-400 coupler.