Post Buy Requirement
MC
United States
Add Review

Our Products

Double Girder Crane

Similar to a single girder crane, but as the name would indicate, is comprised of two parallel girders connecting the end trucks. Like single girder cranes, these can be top or under-running, though a large majority are of the top running variety. The major difference between single and double girder cranes is that the double girder allows the hoist to ride on top, in between, or below the actual girders. In tight headroom applications, this can create better hook height than the single girder alternative.
View Complete Details

Hoists

The hoisting motion can be powered several ways. A Manual Hand Chain Hoist has a loop of hand chain that extends down to the operating floor elevation. The hook is raised by pulling the chain in one direction and lowered by pulling the chain in the other direction. An Air Hoist is pneumatically powered. An Electric Hoist is electrically powered.
View Complete Details

Single Girder Crane

Single girder cranes can be under running (end trucks ride on the lower flange of the runway beam, bridge beam is connected below the end truck) or top running (end trucks typically ride on rail fastened to the top of the runway beam, bridge beam is connected above or to the side of the end truck.) Single girder cranes can be designed and manufactured in a wide variety of capacities, sizes, and spans. The girder on a single girder crane is typically a wide flange beam, although it can be a patented track beam, a truss beam, or a welded box girder for spans over 70 feet. The hoist traditionally rides on the lower flange of a single girder beam.
View Complete Details

Patented Track Crane

Patented Track is an industry name for an engineered, composite beam specifically designed and fabricated for the overhead lifting industry. The beams are made from a hardened rolled tee section welded to webs and flanges of varying sizes depending on the capacity and span required for the application. These beams (used as both runway beams and bridge beams) have much tighter tolerances than commercially available wide flange beams allowing for smoother splices and less ergonomic effort than a traditional wide flange system. The hardened lower flange is also less resistant to wear or grooving.
View Complete Details

Jib Crane

Jib cranes typically have smaller capacities, shorter spans, and are often manually operated. The design is based on a fixed rotating mast and boom with a hoist travelling in and out along the length of the boom. As a result the hook coverages are circular in shape. Jib cranes offer a lot of versatility. They can be freestanding, column mounted, ceiling mounted, or any combination of the three.
View Complete Details

Gantry Crane

Gantry cranes are very similar to traditional overhead bridge cranes except that the bridge beams are elevated on legs above the end trucks. In many applications, the end trucks run on rails at ground level, this is a traditional gantry crane. If one rail is on the ground and the other is elevated on runway beams, this is known as a semi-gantry crane.
View Complete Details

Plate Clamps

Mass Crane is a distributor for many manufacturers of a wide variety of specialized below the hook lifting devices, like the plate clamps pictured above.
View Complete Details

Custom-Designed Spreader Beams

Mass Crane offers custom-designed below the hook lifting devices, like the one shown above and are designed, fabricated, and load tested in-house.
View Complete Details

Monorails

Monorails are very similar to bridge cranes with the one notable exception that the bridge beam is fixed in a permanent location. Like bridge cranes, monorails can be made from Enclosed Track, Patented Track, or Wide Flange beams. Also like bridge cranes, the support structure for monorails can be Freestanding or, if the roof structure is designed and engineered as such, can be Ceiling Mounted.
View Complete Details

Enclosed Track Workstation Crane

Developed in the 1980's, these cranes were introduced as a more economic and ergonomic alternative to manually operated patented track systems. Traditionally limited to capacities of 2 Ton and under and spans of 30 feet or less These systems are typically manually operated (pushpull) for both bridge and trolley motion. Can be freestanding (floor supported with columns and headers) or ceiling-mounted depending on the application and the overhead support structure available. Are a good fit for customers who prefer manual positioning of light capacity lifted loads.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Mass Crane & Hoist, Inc.)
  • Tyngsboro, MA 01879 map, United States
  • Share us via