Post Buy Requirement
MT
United States
Add Review

Other Products / Services

DLE15-2, Double Acting Single Stage Double Air Head Gas Booster

  • Pressure Ratio 30:1
  • Weight 51 lb
  • Displ. per Cycle 14.8 in³
  • Max. Temperature 210 ºF
  • Inlet Gas Connection 1/4"
For high pressure applications or where air drive pressure is low MAXPRO offers three double acting - single stage boosters with a double air head.
These models include the DLE15-2, DLE30-2 and DLE75-2.
View Complete Details

65L4H, 1/4" Stainless Steel Elbow

  • Fitting Pattern Elbow
  • Connection Type 4HF
  • O.D. Tube 1/4 in
  • Orifice 0.094 in
  • Block Thickness 1.02 in
Exceeds industry standard of 60, 000 psi
MAXPRO offers a complete line of MAXIMATOR high pressure fittings, tubing, check valves, line filters, anti-vibration fittings and safety head assemblies, as well as elbows.
View Complete Details

15L4P, Pipe Elbow Fittings Pressure To 15,200 Psi

  • Connection Type 1/4 NPT
  • Orifice 0.201 in
  • Block Thickness 0.79 in
Exceeds industry standard of 15, 000 psi. Pipe fittings are designed for liquid and gas applications. The P Series Fittings are available from 14" to 1" NPT to 15, 200 psi.

NPT threads must be sealed using a high quality PTFE tape andor paste product. Sealing performance may vary based on many factors such as pressure, temperature, media, thread quality, thread material, proper thread engagement and proper use of thread sealant.

Recommends to limit the number of times an NPT fitting is assembled and disassembled because thread deformation during assembly will result in deteriorating seal quality over time. When using only PTFE tape, using thread lubricaion to prevent galling of mating parts is recommended.
View Complete Details

65TU4H-316, 1/4" High Pressure 316 Stainless Steel Tubing

  • Tubing Tolerances 0.248/0.243 in
  • Tube Material 316SS
  • Fits Connection Type 4HF
  • O.D. Tube 1/4 in
  • I.D. Tube 0.083 in
Exceeds industry standard of 60, 000 psi. MAXPRO offers a line of cold drawn thick wall tubing, with flow areas to compliment the high pressure valves and fittings. This tubing is made under strict manufacturing and quality control standards and inspections, with dimensional tolerances to match the requirements of the high pressure coned and threaded connections.

The standard materials are 304 and 316 stainless steels. Other materials may be provided on special request, depending on the specific material, diameters and lengths.
View Complete Details

15M4P, Pipe Hex Close Nipples Pressure To 15,200 Psi

  • Connection Type 1/4 NPT
  • Working Pressure 15200 psi
  • Orifice 0.201 in
MAXIMATOR Pipe Hex Nipples are designed for rapid system make-up. They are available in various lengths for pipe valves and fittings.

In addition to the minimum lengths (Pipe Hex Close Nipples) and standard lengths listed in the table below, Pipe Hex Nipples are also available in custom lengths. Please consult factory.
View Complete Details

15CF4P-5, Pipe Line Filters Pressure To 15,200 Psi

  • Pressure Rating 15200 psi
  • Connection Type 1/4 NPT
  • Orifice 0.201 in
  • Micron Size 5
  • Filter Element Areas 0.82 in²
MAXIMATOR Pipe line filters are used to filter process fluids in high pressure systems. The cup type design is used when maximum filtration surface area and a single micron size element is preferred. This design increases the filter area as much as 6 times the area of the disc type filter, and will permit higher flow rates with a lower pressure drop, and longer intervals between element changes. Filter elements come standard in: 5, 30 or 56 micron sizes and are easily replaced. Filters are rated for temperatures -60F to 660F.
View Complete Details

DLE2-1, Single Acting Single Stage Gas Booster

  • Pressure Ratio 2:1
  • Weight 34 lb
  • Max. Temperature 140 ºF
  • Max. Freq 100 Cycles/min
  • Displ. per Cycle 56.2 in³
MAXPRO offers five gas boosters in the single acting - single stage configurationSingle stage - single acting boosters are the smallest and lightest of the Maximator family, yet capable of output pressures up to 10, 000 psi.
View Complete Details

21V4---YMNO, Air Valve Actuators - Air To Open, Normally Open

  • Material Anodized Aluminum
  • Actuator Operating Temperature -20 to 200 ºF
  • Inlet Air Supply Connection 1/8 NPT
  • Stem Travel 0.25 in
  • Flow Value (Cv) 0.31
MAXIMATOR air operated valve actuators are piston type design, and are mounted on a manual valve to provide remote control capability. There are two styles of air actuators available, and selection is based on the valve size, system pressure, and air pressure available.
View Complete Details

AS-MPLV2-1G, AIR AMPLIFIER SYSTEM

  • Type 2:1 Ratio Systems
  • Tank Size 1.6 gal
  • Length 13.00 in
  • Width 8.00 in
  • Height 22.00 in
MAXPRO Air Amplifier Systems are ideal for turn-key installation at work stations or machine centers to boost plant air pressure for tools or operation of pneumatic clamps, cylinders and other equipment. These systems provide short-term high flow air or constant flow with reserve, at a constant regulated output pressure. Storage tank is per A.S.M.E. Code and CRN (Canada) and comes with a safety relief valve, drain valve and pressure gauge.
Each 200 psi and 250 psi system is also equipped with an inlet air filter and outlet pressure regulator with gauge, all mounted on a common base. The 500 psi and 600 psi systems are equipped with an inlet air filter and inlet air pressure regulator with gauge. High pressure outlet regulator with gauge is available as an option (Add "-R" for a 14" FNPT regulator or "-12 R" for a 12" FNPT high flow regulator to system catalog number). MAXPRO Air Amplifier Systems are available in a number of arrangements and custom designed units are also
View Complete Details

RD-1200, 1/4" Angular Rupture Disc

  • Pressure Range 1164 to 1272 psi
  • Terms and Conditions All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.
14" angular seat rupture discs are designed to be used with the safety head assemblies that are shown above. Minimum rupture disc pressure ratings should be at least 110% of system operating pressure. The standard rupture disc material is Inconel. The pressure ranges indicated in the table below are at room temperature (72F). Other materials and pressure ranges are available upon request.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (MAXPRO Technologies, Inc.)
  • Fairview, PA 16415 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/maxpro-technologies-inc/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0007457984{main}( ).../index.php:0
20.05402028360include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.11022751048include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.11923686744header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice