Post Buy Requirement
ME
United States
Add Review

Other Products / Services

Anchor Set HD

our Anchor Set- Storage Building or All Purpose Use A must for wind protection!
4 Anchor Set 12 Shaft 30 Long w4 Helix. A must for wind protection!
Easy to install by hand! Removable Reuseable
Set consists of:
4- 30 Eye Anchors with 4 Helix Welded closed loop!
Installl by hand or machine both available under Installation tools
View Complete Details

Anchor Special

Product Description


Contractors Save BIG Limited Supply! Ideal for Contractors needing to Anchor down installed Sheds etc.! Up to 2, 300 Lb pull out resistance for each Anchor! Lighter that other style Anchors- Save on *Shipping!
4 Ground Anchor Contractor Bulk Set Special- WITH DRIVE ROD!
These arrowhead Ground Anchors are designed after our highly successful Mil-Spec anchors which have been proven and tested out in the field for over 40 years.
View Complete Details

Hammer

  • Blows Per Minute (variable speed) 730 – 1, 450 BPM
  • Impact Energy (ft.lbs.) 25.7 ft.lbs.
  • Impact Energy (Joules) 34.9 J
Powerful 14 AMP motor delivers 25.7 lbs. of impact energy to handle the most demanding applications
Constant Speed Control automatically applies additional power to the motor to maintain consistent speed under load for the most challenging jobs
Soft Start suppresses start-up reaction for more control and better accuracy
L.E.D. Service Light notifies the user approximately 8 hours before the brushes need to be replaced
L.E.D. Power Lights indicate switch failure or cord damage
Variable Speed control dial enables user to match the speed to the application for greater versatility
Extended Life Brushes are longer for more work between service intervals and less downtime
Automatic Brush Cut-Off protects commutator from damage for longer tool life
No hammering when idling helps increase tool life
Easy-to-operate slide switch increases productivity and allows for continuous use
Side-handle swivels 360 for greater control
Rubberized ergonomic soft grip provides more comfort and control
Makita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life
Durable blow-molded rolling tool case for safe storage and easy transportation
View Complete Details

Sds Max Hammer Drill

  • Capacity (concrete) 4-1/8″
  • No Load Speed 2, 500 RPM
  • Blows Per Minute 680 BPM
orque Limiting Clutch Engineered to Reduce Gear Damage
Powerful 10 AMP motor delivers 4.6 ft.lbs. of impact energy to handle the most demanding applications
2-mode operation for Hammering Only or Hammering with Rotation
Rubberized ergonomic soft grip provides more comfort and control
No hammering when idling functions helps increase tool life
One-touch sliding chuck for quick bit changes
Torque limiting clutch engineered to prevent gear damage by automatically disengaging gears if the bit binds
Sequential impact timing delivers timed hammering during rotation to minimize overlapping bit impacts for up to 50% faster drilling
12 bit angle settings allow the bit to be set at different positions for operating convenience
Automatic brush cut-off protects commutator from damage for longer tool life
12 bit angle settings allow the bit to be set at different positions for operating convenience
Makita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life
View Complete Details

Wire Rope

Package of 10 Cable Clips for 18 Wire Rope
Allows for on site termination of cable
Size: For 18 Cable
Material: Malleable Iron
Coating: Galvanized
Wrench Size: 316
Apply Correctly U bolt should be on end of Rope- Re- tighten after initial load
View Complete Details

Helical Piers

  • Round shaft: 2 7/8″ – 3 1/2″ Larger Diameters Available
  • Square Shaft: 1 1/2 – 1 3/4″
  • Helix Sizes: : 6″ – 16″ Larger Diameters Available
Helical Piers come in different designs- Generally speaking: Round Shaft Helical Piers are used for Compression applications such as foundation repairs and supports for both Residential and Commercial applications in addition to new construction such as Walkways, Building supports, Light poles, Board Walks, Utility equipment etc.
While Square Shaft Helical Piers are used for Tension Applications such as Tie Backs, Anchoring Applications, Guying Towers, Tilt Up construction etc.
View Complete Details

Spline Hammer

  • Capacity (concrete) 4-1/8″
  • No Load Speed (variable speed) 235 – 480 RPM
  • Blows Per Minute (variable speed) 1, 350 – 2, 750 BPM
Makita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life.
SKU: msa-hr4041c Category: Makitaapplications
Constant speed control automatically applies additional power to the motor to maintain speed under load to complete the most challenging jobs
Soft start suppresses start-up reaction for more control and better accuracy
Variable speed control dial enables user to match the speed to the application for greater versatility
Torque limiting clutch engineered to prevent gear damage by automatically disengaging gears if the bit binds
Sequential impact timing delivers timed hammering during rotation to minimize overlapping bit impacts for up to 50% faster drilling
Automatic brush cut-off protects commutator from damage for longer tool life
2-mode operation for Hammering Only or Hammering with Rotation for multiple applications
No hammering when idling function helps increase tool life
High quality aluminum housing for greater durability and longer tool life
Makita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Milspec Earth Anchors)
  • Alexander City, AL 35010 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/milspec-earth-anchors/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0005457952{main}( ).../index.php:0
20.02022015288include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.28202737448include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.28773673144header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice