Post Buy Requirement
MM
United States
Add Review

Other Products / Services

Round Duct

MKT products are factory fabricated to meet or exceed 3rd edition 2005 SMACNA Standards. MKT Standardizes rounded duct typically with USA mill-stamped, G90 galvanized steel*. We not only meet requirements set by the state and federal entities, but our highest standards are held by our own quality control guidelines.
*Specific needs and application do apply
Snap lock
Economical. Shipped knocked-Down and assembled in the field. Typically used for light commercial or multi-family residentialcondosapartments. Easier to take mass quantities to a multi-story job. Normally wrapped in the field for installation. Low pressure work.
Flange
Connecting System, 2 different flanges, angle ring flange (Accuflange spiral, commercial HVAC application). Industrial flange (Burkholder)-high heat, high pressure, high velocity.
Van Stone Flanges
Practical and labor saving method for connecting both industrial duct and pipe. Industrial duct: the Van Stone connection consist of a face flange and a backing
flange with a slip fit over the duct. The face flange is mechanically formed from the end of the duct section by turning the edge of the duct and forming a lip with an outside diameter small enough to clear the connect bolts.
Double Wall
Double wall Solid Inner (only R value) and Double Perf Inner (R value and decibel ratings). 2 different scenarios: Insulate the pipe for an industrial application solid inner. Perf, are wholes in trap sound as well as R Value and decibel ratings.
Welded
A fabrication or sculptural process that joins materials. A level beyond HVAC applications to enclose fumes, biologicals, high pressure, particulate.
View Complete Details

Rectangular Duct

MKT products are factory fabricated to meet or exceed 3rd edition 2005 SMACNA Standards. MKT standardizes most rectangular duct construction with USA mill-stamped, G90 galvanized steel. We not only meet requirements set by the state and federal entities, but our highest standards are held by our own quality control guidelines.
*Specific needs and application do apply
Snap Lock
Economical. Shipped knocked-down and assembled in the field. Typically used for light commercial or multi-family residentialcondosapartments. Easier to take mass quantities to a multi-story job. Normally wrapped in the field for installation. Low pressure work.
Slip and Drive
Assembled in the field. Typically used for light commercial or multi-family residentialcondosapartments. Size of the duct has a lot to do with where you use slip and drive. Needs to be sealed after installed. Its used in low to medium pressure systems.
TDC Flange (Transverse Duct Connections)
rectangular-ductworkTDC flange is a roll form flange connection that provides a solid metal connection directly onto the duct reducing air leakage. Typically used for light and heavy commercial. It is quicker to install in the field, more leakage resistant that slip and drive. Uses a 4 bold connector system. The gasket is designed for low, medium and high pressure systems.
Double Wall
A double-walled duct is a secondary contained duct system. It is a duct within a duct, or encased in an outer covering, with an annulus (interstitial space) between the two diameters. The inner duct is the primary or carrier duct and the outer duct is called the secondary or containment duct. Conditioned space, quieting space.
Welded
A fabrication or sculptural process that joins materials. Typically used requirements are biological consideration (pharmaceutical), (duct must be sealed) or exhaust requirements, smoke, fumes, dust collection systems.
Application
Rectangular Duct is best used when physical space limitations and high air carrying capacity requirements are tight.
Marketable Applications
Ventilation Systems, HVAC Systems, Dust Collection Ventilation, Heating and Air Conditioning
Rectangular Duct Installation
Delivered with our product, all supplies come with connecting hardware, including, slips and drives, nutsbolts, gasketed materials and hanging system.
All rectangular duct (except Snap Lock) can be lined with fiberglass, closed-cell foam, or any other industry material. On instances where specified, we can also manufacturer double wall duct.
View Complete Details

Coupling

MKT recommends using slip in couplings up to 24 diameters
Quick, simple, relatively inexpensive
Light to moderate strength characteristics
Requires sealing in the field if necessary
View Complete Details

Flanged

Simple installation process
Can be installed on-site
Shop installation has proven to:
protect the ends of spiral in transit
reduce labor time in the field
Available in 8 to 72 in standard 2 increments
Requires sealing in the field or the shop if necessary
View Complete Details

Barrel Clamp

Self Sealing
Time and labor saving
Adjusts automatically to slight duct diameter variations
Offers inner ring for use with Spiralmate on Double Wall spiral connections
Has been lab tested to 18 positive WG and 10 negative WG
View Complete Details

Angle Rings

Typically used in heavy, industrial applications
Larger diameter and gauge spiralround duct uses angle rings
Can be used in conjunction with van stoning on the round duct for a slip ring capability
Requires additional gasketing if required
Available in all materials including galvanized, pricing and availability on request
View Complete Details

Weatherguard Duct Systems

MKT sets a new standard in
economic and efficient exterior
duct systems.
weatherguardfeatureWeatherguard Duct Systems, an innovative design by
MKT Metal Manufacturing, provides a fully sealed and weather
resistant system.
When a buildings internal space is at a premium or nonexistent, rooftops are often a choice in the placement of duct work. Our pre-insulated, weatherized, double-wall spiral duct system provides many advantages.
Round
Most efficient air conveyance
Reduced snow load
Reduces wind uplift
Structurally sound design
Pre-manufactured SystemWeatherguardProduct_RGB-1
MIRO Industries Inc.
Installation preparation
Controlled environment manufacturing
Consistent

Weather Protected
3M VentureClad Insulation Jacketing Tape
Protected from the elements
Impervious to moisture and weather
Reflective surfaces
Barrel Clamp
Quick connections
Adjustable
Closed cell seal
Labor saving
Less Joints=Less Labor
Drastically reducing installation and insulation costs
Minimal Thermal Brakes
Not easily used as a catwalk after installation
Optional Agion Microbial Protected
Currently laboratory-tested by InterTek, York, PA
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (MKT Metal Manufacturing, Inc.)
  • York, PA 17402 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/mkt-metal-manufacturing-inc/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0007457952{main}( ).../index.php:0
20.02662015080include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.04932737760include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.05813673464header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice