Page Industrial Equipment, Inc.

FEEDWATER TREATMENT Feedwater Treatment Systems and Chemicals for Maximum Efficiency and Longevity of Your Clayton Steam Generator Page Industrial can help you configure the right feedwater treatment system to match your steam generation and recovery goals. Most systems include the following components: Water softening Chemical injection Feedwatercondensate receiver Blowdown tank with a cooling water valve Consultation is important Duraflame It’s important to consult with a feedwater specialist such as Page Industrial since the type of receiver chosen depends on several factors, especially the temperature and the amount of the condensate returned from the steam system. Categories of systems include: An “open” or atmospheric deaerating system A semi-closed system Pressurized deaerators Skid or individual Components for the above systems can be configured in a skid mounted fashion or individually, and are available in factory piped and wired packages. Chemicals Since 1935, the Clayton Chemical Division has been providing boiler chemical products and services and state-of-the-art technology for optimum steam generator system performance. These products and services will ensure productivity, cost savings, lower maintenance costs and provide significant benefits including: Reduced blowdown Fuel conservation Less fuel, water and water treatment waste Automatic feed systems Condensate management Boiler water products for conventional boilers TDS controller Cooling tower products Closed system inhibitors Corrosion control agents Laboratory and technical support

SIGMA FIRE Efficient, Compact, Rapid-Start Steam Generator Systems (25-200 BHP) See our E-Series page for boilers between 150 and 1, 000 BHP. SigmaFire boilers are designed from the ground up for efficiency and productivity, and come in a range of sizes to fit your needs. Duraflame Installation time and expenses are greatly reduced as a result of modular construction of the main components (the steam generator, the feedwater tank and other feedwater equipment). Each of these components is built on two rails that slide and bolt together to simplify shipping and field installation. This new design uses radiation heat to pre-heat combustion air and a redesigned main heating coil to improve efficiency and lower fuel consumption. All units use the latest PLC microprocessor main system controls to enhance operator interfaces and serviceability. Units are available with the latest servo-based burner management systems for improved pressure control, load following and repeatability. Advanced design and construction greatly reduces noise levels and results in exceedingly smooth operation, and ultra low NOx burner systems are available to meet the latest and most strict emissions standard down to below 9 ppm. Clayton steam generators features and benefits: High-quality, consistent steam output Compact size Smaller space and lower weight requirements High degree of safety High fuel-to-steam efficiencies Quality steam Extremely reliable Rapid startup capability Fast response to load swings, with no carryover Reduced blowdown and lower water waste Inherent high level of operator safety In-line option for maximum efficiency An in-line multi-unit system is a good choice for steam requirements that vary from week to week or even hour to hour. With an in-line system you can: Reduce operating costs Better control steam output Reduce blowdown Increase turn-down Increase efficiencies Reduce chemical usage

SUPERHEAT Integral, Superheated Steam With No Need For a Separate Heater Superheat Clayton’s superheaters are unique because they have been designed as an integral part of a generating system and can provide either saturated or superheated steam. Steam can be generated at temperatures up to 650°F (343°C) and pressures up to 850 psig (57 bar). These exceptional superheat units use the same reliable Clayton steam generator design with a superheater section added to the helical coil, meaning there is no need for a separately fired superheater. If you have the need for an auxiliary boiler, you’ll love the benefits of Clayton steam power. Compact design High degree of operator safety—non-explosive design Rapid start—from a cold state to full output in 20 minutes Fast response to load swings Low maintenance—single burner

E-SERIES Efficient, Compact, Rapid-Start Steam Generator Systems (150-1, 200 BHP) E-Series See our SigmaFire page for boilers between 25 and 200 BHP. Clayton’s E-Series line of boilers are compact and highly efficient. With a unique flowcounter-flow heat exchanger, these steam workhorses start up fast and react quickly to system load changes without compromising system pressure. Another advantage of Clayton’s E-Series is the way these generators control internal water flows to carefully manage TDS build-up, and how they dispose of the water in a concentrated manner that reduces wasted heat, water and chemicals. All of this is accomplished without the need for a large pressure vessel, for a safer environment in the boiler room. Just a few of the many advantages of Clayton’s E-Series line of boilers: Quick startup High-quality, consistent steam output Inherent high level of operator safety Low weight and space requirements Strong fuel-to-steam efficiencies Quick response to load swings, with no carryover Lower water waste and reduced blowdown Low NOx, skidding, packages systems and more available With the Clayton E-Series, low NOx systems are available to meet regulations down to 6 ppm. We also offer skidding, mounting, containerizing and other options enabling greater flexibility in your choices for steam generation.

STAND-ALONE ECONOMIZERS Leverage Your Boiler Exhaust Gases to Your Advantage Condex Most boilers lose 15% to 20% of their fuel input energy as waste heat. The ConDex stand-alone economizer, which maximizes heat recovery, will reduce costs, lower your CO2 emissions and lead to stronger environmental responsibility. Using lost energy The combustion process of most fuels takes hydrogen from the fuel and oxygen from the combustion air and combines the two to form water, which is then instantly vaporized. The vaporization of the water consumes energy and absorbs approximately 17% of the total heat energy created by the fuel and it is usually lost to the atmosphere. This system allows you to recover this lost energy. This economizer heats a cold input water stream that consumes live energy – such as hot water, steam or electricity – to heat, and transfers this wasted energy back into your process. The system transfers enough energy to cool the gas below the water vapor dew point, recovering the heat and creating a viable water source. Avoiding CO2 emissions Since 12% by weight of exhaust gas is water, you can save significant energy through the recovery and use of latent heat. Every cubic foot of gas saved eliminates one cubic foot of CO2 released into the atmosphere. Traditional economizers are not designed to cool exhaust gas below the water vapor dew point as they would rapidly corrode and penetrate water back into the exhaust gas breaching. As a stand-alone system, this economizer is designed to keep these processes separate. In addition to substantial energy savings, the system also recovers water that would be lost to the atmosphere and can be reused.

Packaged Steam Systems, Ready to Fire Up Packaged steam generating systems from Clayton Industries are available in a variety of standard and custom designed configurations. They provide compact, convenient packages that are fully wired, assembled and piped at the factory. Clayton steam generator packages: Reduce installation time Reduce installation cost Ensure the proper size and type of interconnecting piping and wiring Ensure complete system compatibility and integrity Common packaged configurations include: Steam Generator Skid Mounting: piping and wiring of the steam generator along with all the water treatment skid components Water Treatment Skid Mounting: piping and wiring on a common skid of the feedwater receiver, water softeners, chemical feed system, blowdown equipment and booster pumps Feedwater Receiver Skid Mounting: piping and wiring of the feedwater receiver Fully Containerized Packages: steam generator and feedwater system are installed in a fully weather protected enclosure