Other Products / Services #5217701

Output Circuit:Single phase Isolated; taps from 0-65 to 0-300VRegulation: Adjustable to 0.1% line and loadShort Circuit Protection: Thermostat and fast acting line fusesFrequency Response:Full power 30Hz-5KHz with standard output transformer10Hz to20KHz with external output transformersDistortion: 0.3% mid bandTransient Overload 4.5X full load for 5 sec for motor startingInput Power: 208 5060 3 phase unless otherwise specified can easily be wired for 190, 225, 240, 380, or 450V; 5060Hz Power Factor Range: +0.7 to -0.7 for full power; to zero @ reduced powerDimensions: 19 rack by 22 deep 12.25H under 2000S, 17.5H 2000 & 3000S

For three phase models with less or equal to 750 watts output power, stand-alone units are available. Please refer to Frequency Converter Category for detail information. For three phase set-ups (750 watts to 9000 watts), three individual Powertron units are required. They may be connected in Y or DELTA. Any line to line or line to neutral voltage desired may be selected by choosing the appropriate output transformer tap. All necessary interconnecting cables and a three phase oscillator are included in all three phase combinations. A cabinet is not included. Consult the factory for choices of cabinets, casters slides, etc.

ndustrial Test Equipment Co., Inc. manufactures high frequency output transformers in accordance to the customers specifications. ITECO manufactures output transformers in the frequency range of 30Hz to 2MHz; output power from 50 watts to 20, 000 watts; output voltage from 1V rms. to 6000V rms. (up to 10, 000V rms. in some frequency ranges); output current from 0.01A to 400A (up to 1500A rms. in some frequency ranges). Due to different applications, ITECO output transformers can be categorized as: (1) High frequency low inductance output transformers(2) High frequency low stray capacitance output transformers(3) High frequency high voltage output transformers(4) High frequency high current output transformers(5) High frequency wide-band output transformers.

The Model 5900 is a high general purpose audio generator. The circuit consists of a low distortion oscillator, a drive amplifier, and a bipolar FET class AB1 power amplifier with an output transformer. The output transformer has three taps to allow utilization of the full power over a wide range of voltages. A frequency counter and output voltmeter are built in. Electronic overload protection is provided that limit the power into a short circuit to a safe value. SpecificationsInput Power: 120V AC 50Hz60Hz (Unless Otherwise Specified)Output Volts: Low Range . 0 to 8.5 V rms. @ 8.2 AMiddle Range . 0 to 38 V rms. @ 1.8 A High Range . 0 to 130 V rms. @ .53 A 0 to260 V rms. on request Regulation: 0.1% line and loadDistortion: 0.3% mid bandOutput Power: Maximum . 70 VAContinuous . 50 VAFrequency Response: 45Hz to 20 KHz Frequency Accuracy: 0.1%Dimensions: 12.25 X 5.25 X 12.5Weight: 23 lbs

Output Circuit:Isolated output transformerInput Power: 115 or 230 volts 50 or 60 HzRegulation: 1% line and loadFrequency Response: 30Hz to 5KHz for standard model, up to 500KHz for special made models.Short Circuit Protection: Automatic reset thermostatDistortion: 0.3% mid bandPower Factor Range: +0.7 to -0.7 for full power; to zero @ reduced powerSpecial Output Range Customer could specify any ranges up to 1500AWeight

Output Circuit:Isolated output transformer; taps from 0-8 to 0-260VRegulation: Adjustable to 0.1% line and loadShort Circuit Protection: Automatic reset thermostatFrequency Response: Full power 45Hz-20KHz, reduced power 20Hz-40KHzDistortion: 0.3% mid bandVolt Meter: Analog (not included in Model 80S)Input Power: 115 or 230 volts 50 or 60 HzPower Factor Range: +0.7 to -0.7 for full power; to zero @ reduced powerDimensions: 5 14 rack by 14 deep

Output Voltage:0-130V or 0-260V with internal output transformer0-22.5 rms. into primary of external output transformerFrequency Response: 40Hz to 20KHz with internal output transformer20KHz to 200KHz with external output transformers (at additional cost) Regulation: 1 % line and load on transformer primary side.Distortion: 0.5% mid bandInput Requirement: 0-2V rms. into 600 ohmsShort Circuit Protection: Automatic reset thermostatOutput Meter: 0-30V analog volts meter on primary of output transformerOptional Output Transformer: up to 10, 000V rms. and up to 200A availableInput Power: 120V or 230V 5060 Hz for model 250S-HF. 350S-HF and 500S-HF208V or 190, 225, 240, 380, or 450V 50Hz60Hz for model 1500S-HF

Frequency Range: 20 Hz 10000 Hz in .01 Hz stepsOutput Waveform: Sine wave or Square waveFrequency Accuracy: +- .05% of programmed frequency Frequency Stability: 5 PPM per degree C from 0-50 degree CDistortion: Less that 1% over frequency rangeOutput Amplitude: 0 - 1.000V rms. Programmable in 0.001V stepsVoltage Accuracy: +- 0.5% of full voltage range Voltage Stability: +- .02% of setting, 0-50 deg. C Voltage Regulation: +- .5% 0-full load, +- .05% 110V-130V LinePhase Angle Range: 0-360 in 0.1 degree incrementsPhase Accuracy: +- 1 degree over frequency range for programmerPhase Relationship: phase 2, 3, 4, 5 and 6 programmable independently with respect of phase 1

All models are pure linear circuitry with less than % total harmonic distortion. Output frequency and voltage must be specified on the order. Any frequency from 30Hz to 30KHz and any voltage from 5 to 2000V rms. may be specified. These frequency converters are preset to the values specified on the order. There are no external adjustments normally provided. However, if external adjustment of output voltage is specified it can be provided at no additional cost. An analog voltmeter is standard on all Models except 20C. Variable frequencies and digital frequency display is available if specified (at additional cost).Weight(Lbs)

Fixed 400HzFreq. Accuracy: 0.1% of settingTH Dist: 0.35% Model A2 is two phase (90o apart) output.Model A3 is three phase (120o apart) output.Model A-534 is built-in with 0-10V DC controller.Model ASQ is sinesquare output switchable.BFixed 60HzFreq. Accuracy: 0.1% of settingTH Dist: 0.35% Model B2 is two phase (90o apart) output.Model B3 is three phase (120o apart) output.Model B-534 is built-in with 0-10V DC controller.Model BSQ is sinesquare output switchable.CFixed 50HzFreq. Accuracy: 0.1% of settingTH Dist: 0.35% Model C2 is two phase (90o apart) output.Model C3 is three phase (120o apart) output.Model C-534 is built-in with 0-10V DC controller.Model CSQ is sinesquare output switchable.FFixed two fixed frequenciesFreq. Accuracy: 0.1% of settingTH Dist: 0.35%User can specified frequencies Model F2 is two phase (90o apart) output.Model F3 is three phase (120o apart) output.Model F-534 is built-in with 0-10V DC controller.Model FSQ is sinesquare output switchableS20Hz to 20KHz adjustableResolution: 0.1 Hz stepsTH Dist: 1%Freq. Accuracy: 0.01% of setting4-12 digit frequency display Model S2 is two phase (90o apart) output.Model S3 is three phase (120o apart) output.Model S-534 is built-in with 0-10V DC controller.Model SSQ is sinesquare output switchable.K20Hz to 20KHz adjustableResolution: 0.1 Hz stepsTH Dist: 1%Freq. Accuracy: 0.01% of settingThumbwheel Selection: 6 digits. No two phase or three phase version available.Model K-534 is built-in with 0-10V DC controller.No square wave output available. XA-1 For Amplifier Version UnitsIt creates continuity with 1-sec time delay.