Post Your Requirement Menu

Welcome User

Other Products / Services

Our Complete range of products are REC-B105YC: 9 Ton Scissor-Type Cutting Tool, REC-P600R: Wireless Remote Hydraulic Pump, HTS-4040-U H Tap Removal Die, HTS-4040 Kearney H-Tap Splitter Die and REC-54GRB: Gear Driven 5/8 Ground Rod Bender.

REC-B105YC: 9 Ton Scissor-Type Cutting Tool

The REC-B105YC is designed to cut copper and aluminum cables as well as lead-sheathed telecommunication cables. The extremely large jaws and scissor-type blades allow for easy cutting of large underground cables. The sidebar handle allows the user to stabilize and balance the tool.

View Complete Details

REC-P600R: Wireless Remote Hydraulic Pump

The Huskie REC-P600R is a wireless, remote operated, single acting hydraulic pump. It is our lightest most versatile hydraulic pump. The REC-P600R incorporates a high frequency receiver exclusively paired to a heavy duty cordless remote. The weather resistant IP65 rated remote utilizes two push buttons to advance and retract the tool. Please view the REC-P600R Product page for tool facts and more information.

View Complete Details

HTS-4040-U H Tap Removal Die

The Huskie HTS-4040-U is an H-tap removal die that fits “U” type die compression heads including: SL-C510, REC-6510, EP-510HC, EP-510C & REC-3510 style compression heads. The HTS-4040-U aids in clean removal of H-taps from #6 SOL to 40 ACSR.

View Complete Details

HTS-4040 Kearney H-Tap Splitter Die

The Huskie HTS-4040 is an H-tap removal die that fits all WH-2 & WH-3 Kearney style compression heads. The HTS-4040 aids in clean removal of H-taps from #6 SOL to 40 ACSR.

View Complete Details

REC-54GRB: Gear Driven 5/8 Ground Rod Bender

The REC-54GRB is a heavy duty copper ground rod bender, primarily used in substations to ground structures and equipment. 40 or other size copper used for typical methods of substation grounding can easily be cut and stolen. The REC-54GRB allows you to bend 58” ground rods around concrete footings and attach structures directly to the grounding grid while also making it much harder to cut and steal. The REC-54GRB is clearly marked to make 30, 45, 60 & 90 degree bends but any degree bend is obtainable by feathering the tool to the desired position. The smooth rolling guides allow the ground rod to roll while making a bend so that the copper cladding on the ground rod remains intact without any scuff marks or rippling in the cladding which could cause the ground rod not to perform correctly.

View Complete Details

SH-370M: 35 Ton Hydraulic Steel Punch

The portable SH-370M punch was designed to punch holes through 12” mild steel, aluminum and copper. The punched hole size is 116” larger than your bolt size. A stripper guide extends on either side of the ram to strip the material after punching. This hand-held unit will operate from any 10, 000 psi hydraulic pumping source.

View Complete Details

SL-95YC: 9 Ton Scissor-Type Cutting Tool

The SL-95YC is designed to cut copper and aluminum cables as well as lead-sheathed telecommunication cables. The extremely large jaws and scissor-type blades allow for easy cutting of large underground cables. The sidebar handle allows the user to stabilize and balance the tool. This tool also has a built-in bypass cartridge to avoid cutter damage for those cables that are beyond the cutter’s capacity. The open jaw design allows the user to scoop up cables that are against a wall, in hard to reach areas andor the ground.

View Complete Details

SL-C610: 15 Ton Streamline Compression Tool

The SL-C610 is built on a similar platform as our SL-ND tool, the most robust and versatile streamline tool in the industry. The new SL-C610 will deliver 15 tons of compression force, utilizing all industry standard “P” dies. The capacity of the tool is the same as the REC-3610, capable of accepting lugs up to 1500MCM copper and 1250MCM Aluminum. The new housing design incorporates a rubber over-mold handle grip as well an optional handle allowing the operator better tool control.

View Complete Details

BP-82: Lithium-Ion Battery

The BP-82 is a NEW 2.0Ah battery pack designed to replace the BP-80 with a smaller, more company size for use with the ECO-series in-line tools. The BP-82 will be included as the standard battery pack with all the ECO-series tool kits. It can be charged with any of the Huskie Lithium Ion chargers, including the CH-80, CH-90 & CH-94.

View Complete Details

CH-94: Lithium Ion Charger

The NEW CH-94 is a Lithium Ion only charger able to charge the BP-80 and the NEW BP-82 & BP-84 Huskie Tool Batteries.During its 1 hour charge time, the CH-94 monitors battery temperature and battery voltage for correct charging. The design of the charger allows for stability while in motion by allowing the battery to be clipped in place.It also has completely re-designed contacts for a stronger engagement with the battery terminals.

View Complete Details

Tell Us What are you looking for? Will call you back

Contact Us

  • Salt Lake City, UT 84104 map, United States