Post Buy Requirement
RR
United States
Add Review

Products / Services

SIX-PACK Rapid Deployment Unit

Made in the USA, the Razor-Ribbon Six-Pack Rapid Deployment Unit (RDU) is comparable to our popular Triple Strand Rapid Deployment Unit, but with an even greater level of security in height and Razor-Ribbon. The RDU is designed to quickly deploy for emerging threats. It has the capacity to deploy 247 ft, or approximately 75 m, of Razor-Ribbon in just a few minutes! It can also be recovered manually using only 2-3 people in approximately 20 minutes. The Six-Pack RDU can be utilized as a temporary or permanent barrier.

The RDU comes preassembled and stacked in a pyramid configuration on a magazine. It consists of six 24 (610 mm) of barbed tape. The magazines can be deployed quickly and efficiently by most vehicles with towing capability.

Utilizing the Six-Pack RDU eliminates the need for a large crew working hours in the field, and any potential hazards that go with it. This unit only requires two to three people to deploy.

The barbed tape in this unit comes in either galvanized or stainless steel with short, medium or long barbs. The coils are fastened together in an alternate loop arrangement to minimize any intrusion attempts.

Usage for this six-pack rapid deployment unit is economical and simple. Its a reusable system to provide the military, police, nuclear power plants, power grid, municipalities, and commercialindustrial security integrators with instant physical perimeter protection.

Materials

The Six-Pack RDU comes standard with Razor-Ribbon short barb material. This material was specifically designed to rapidly deploy for permanent or temporary applications. This RDU is considered a delay barrier. It can be customized with any of the full line of Razor-Ribbon barbed tape products.

Installation of this RDU is Easy as 1, 2, 3

Three easy steps deploys nearly 247 of Razor-Ribbon in just a few minutes.

SET
Set the RDU in place using any vehicle with fork attachments. A trailer option is available.
STRETCH
Deploy the unit with a two to three man team. In just two minutes, a 247 six-pack barrier is in place.
SECURE
Anchor the supports in place.
View Complete Details

RAZOR RIBBON MESH PANEL

Razor Ribbons Mesh Panel is the first line of defense to secure a perimeter, from Medium to High to Ultra High security fencing. It is an expanded metal panel with strands of Razor Ribbon secured on the panel. This system can accommodate the weight of additional perimeter security appurtenances including razor wire, surveillance equipment, and anti-tunneling expanded metal mesh panels.

The Mesh Panel is an imposing physical deterrent designed to keep you safe. This system has anti-climb properties with small openings filled with razors. The anti-cut feature would require a potential intruder to make more than 25 individual cuts through the expanded steel before making a hole large enough to climb through. They would also need a specialty tool to cut through, breaking in with this system is nearly impossible.

The Mesh Panel is available in galvanized or stainless steel.

Size Offerings

Panel Width: 4-0 and 5-0
Panel Height: 6-0 and 12-0
Diamond Size: 2 wide, 6 high
Medium and short barb
Features and Benefits

Manufactured in the USA
Rigid, withhold wind load
Corrosion-resistant
72% open with Razors
Easy Installation Installs more accurately without waste, dragging or overlapping
No springing action during installation, resulting in less field work
Can be installed new or as a retro-fit over current chain link fence or chain link fence framework
Can be attached to any fence framework for added protection
Installs similarly to high security expanded metal fencing using standard chain link fence procedures and techniques
Fittings are some of the strongest in the industry and can be locked with breakaway nuts and bolts for added security
Ships on flat pallets for easy handling
USES: Airport, Utilities, Refineries, Nuclear, Energy, etc.
View Complete Details

SENSOR CLIP

  • PART NUMBER 911780
  • DESCRIPTION Sensor Clip for securing the sensor cable to the Razor Wire
  • BOX QUANTITY 50
Razor Ribbon developed a new way to connect hanging sensor wire inside barbed tape without chaffing or setting off false alarms with the new Sensor Clip. The simplicity of the product design also allows for a quick and easy installation.

The Razor Ribbon Sensor Clip comes with a host of Features and Benefits:

Cost-Effective Only uses (1) fastener and a self-tapping screw that can be driven using commercially available powered screw driver with magnetic tips. Other clamps considered for this application involved multiple pieces of connecting hardware (nuts and bolts).
Easy-to-Install The simple design allows the installer to drape the clip over the Razor Ribbon, freeing up a hand for easier installation.
Secure Connection The width of the clamp is sized to match the notches cut into the edges of the Razor Ribbon to securely locate the clip, holding the sensor block and the cable on center between the barb clusters.
Chain Link Fence Use The thickness of the clip matches the diameter of the wire used for chain link fences. As a result, the clip does not need barbed connectors to secure the clip as is used for connection to fence.
Flexible Works with any Razor Ribbon product
Made in the USA We proudly manufacture our Sensor Clips in America
Previously, a typical means of supporting sensor cables was using wire ties to connect the cable directly to the razor ribbon. This caused chaffing of the wire insulation and false alarms. This concern was addressed by providing a distance between the connection to the Razor Ribbon and the connection to the cable.

When using the clip to secure the cable, the notches cut into the sides of the clip and can be used with conventional wire ties, but are wide enough to use commercially available stainless steel tubing clamps. The notches also provide anchorage for either connection method restricting the cable tie or tubing clamp from sliding off the end.

Razor Ribbon continues to be the optimal choice for perimeter security protection by engineering and developing new innovative products. For pricing or more information on the Sensor Clip, contact us today!
View Complete Details

Minimum Security

  • Length 263'
  • Weight 15 lbs. 6.8 kg.
  • Length 527'
  • Weight 28 lbs. 12.7 kg.
Minimum Security for Construction and Manufacturing Sites
Razor Strand barbed tape obstacle is an alternative to traditional barbed wire for low level security applications when added psychological deterrence is desired. It can be installed in lineal strands per barbed wire specifications or coils may be ordered as a substitute according to Barbed Tape Concertina dimensions.

Barbed Tape shall be fabricated from zinc-galvanized steel and shall conform to ASTM A 525, Rockwell hardness (15T) 80-85. Barbs shall be alternately offset .15 .45 inches from the plane of the tape centerline.

The galvanized steel core wire shall be in accordance with ASTM A-764, Finish 2, Class II, Type 3, with a minimum tensile strength of 220, 000 PSI. Barbed tape width shall be .75 inches. Barbs shall be .75 inches in length and punched at 1.34 inch centers.

USES: Minimum-Medium security, construction sites, manufacturing and other low level security applications.
View Complete Details

Low Level Security

  • NSN 5660-01-457-9757
  • DIA. 18"
  • COIL LOOP 33
  • STRIP MATL. SS
Low Level Security Applications
Razor Ribbon Helical is the barbed tape most recommended for private and industrial use. It has the same long barb features as Maze, Supermaze, and NATO Barrier, but the loops are not clipped together in a concertina fashion, allowing the barbed tape to be installed with a variety of loop spacing options, depending upon the level of security required.

Tape Material: 430 Stainless Steel 1 wide prior to forming
Core Material: Galvanized or Stainless Steel .098 diameter
Barb LengthSpacingOffset: 2.5 (+-.10) tiptip 4 on center

USES: Low level security applications such as warehousing, manufacturing, parking lots, storage, and other security applications.
View Complete Details

Exterior Perimeter Security

  • Tape Material 430 Stainless Steel | 1″ wide prior to forming
Exterior Perimeter Security Products
Maze barbed tape is the original long-barb, wire-reinforced concertina and is highly recognized in the industry as the long-barb, wire-reinforced concertina and is used in more minimum to medium security applications than any other Allied Tube & Conduit barbed tape product.

Single coil wire reinforced concertinas are fabricated from 0.025 thick AISI 430 (SS) stainless steel or ASTM A653 (GA) galvanized steel. Each roll consists of 31 coil loops with pairs of loops alternately clipped together. Clusters of four needle sharp barbs are located 4 o.c. along the spiral turns. Concertina rolls are available in combinations of SS or GA, tape and core wire. Barbed tape is wrapped 230 around 0.098 diameter SS or GA core wire.

Tape Material: 430 Stainless Steel 1 wide prior to forming
Core Material: Galvanized or Stainless Steel .098 diameter
Barb LengthSpacingOffset: 2.5 (+-.10) tiptip 4 on center

Uses: Minimum to medium security confinement and detention applications, low level utility companies, airport perimeters, etc.
View Complete Details

Maximum Security Barrier

  • Barb Length/Spacing/Offset 2.5″ (+/-.10″) tip/tip | 4″ on center |
  • Tape Material 430 Stainless Steel | 1″ wide prior to forming
Maximum Security Barrier Applications
Supermaze and Nato Barrier barbed tape products are designed for high density maximum security applications. Nato Barrier barbed tape was given its name after being successfully installed around several extremely sensitive NATO facilities in Northern Europe.

Single coil wire reinforced concertinas are fabricated from 0.025 thick AISI 430 (SS) stainless steel or ASTM A653 (GA) galvanized steel. Each roll consists of 51 coil loops with pairs of loops alternately clipped together. Clusters of four needle sharp barbs are located 4 o.c. along the spiral turns. Concertina rolls are available in combinations of SS or GA, tape and core wire.

Barbed tape is wrapped 230 around 0.098 diameter SS or GA core wire.

Tape Material: 430 Stainless Steel 1 wide prior to forming
Core Material: Galvanized or Stainless Steel .098 diameter
Barb LengthSpacingOffset: 2.5 (+-.10) tiptip 4 on center alternately offset .15 .45

Uses: Maximum Security
View Complete Details

Maximum Security Confinement Applications

  • NSN 5660-01-495-6363
  • DIA. 30"
  • COIL MATL. SS
Maximum Security Confinement Applications
Instabarrier non-reinforced barbed tape is characterized as being the most versatile of all barbed tape products. Designed for both temporary and permanent use, it permits rapid recovery and reuse.

Single coil non-reinforced concertina 30 in diameter are fabricated from steel. Each roll consists of 101 coil loops with pairs of loops alternately spot welded together at five locations around the circumference.

Cluster of four needle sharp barbs are located 4 o.c. along the spiral turns. Non-reinforced concertinas are only available in stainless steel.

Tape Material: 301 Stainless Steel 1.21 wide prior to forming
Barb LengthSpacingOffset: 2.5 (+-.10) tiptip 4 on center alternately offset .15 .45

USES: Maximum security confinement applications, nuclear generating plants, petroleumchemical storage, refiners, sensitive areas at airports and nuclear weapons storage, etc.

Instabarrier (NON-REINFORCED) Single Coil Concertina Rapid Deployment

NSN DIA. LOOPS COIL MATL. STRIP CABLE WELDS LOOP SPACING COIL YIELD PKG. ASTM F 1910 ITEM#
5660-01-495-6363 30" 101
View Complete Details

Single Coil Wire Reinforced Concertinas

  • NSN 5660-00-921-5516
  • DIA. 38"
  • COIL LOOPS 56
Single Coil Wire Reinforced Concertinas
Single coil wire reinforced concertinas, 38 in diameter are fabricated from 0.020 thick ASTM A653 (GA) galvanized steel strip. Strip is clinched around a galvanized steel core wire. Each roll consists of 56 coil loops with pairs of coil loops alternately clipped together at five locations around the circumference. Each coil extends to 50 when deployed at 21 coil spacing. Two opposing handles at each end are attached to the end coils. Refer to Military Specifications A-A-555-22A for additional information.

USES: Military battlefield and training barrier.

Military Tactical Barrier Concertina Coil (WIRE-REINFORCED)
View Complete Details

RAZOR-RIBBON FENCE PICKETS

Allied Tube and Conduits fence picket is designed for the rapid installation of security perimeter. After the post is driven into the ground, barbed wire is inserted into the built-in slots along the length of the perimeter. This system can either stand alone or be augmented with the addition of barbed tape concertina attached to the barbed wire when needed.

Manufacturing

The fence picket is constructed from steel conforming to ASTM A1011, producing a yield strength of 50, 000 psi, and complies with federal specifications and GSA guidelines for Fence Post, Drive Type, Spadeless.
The standard exterior color is forest green with additional colors andor galvanization available upon request.
The posts, depending on length, have alternating slots on each side every 9 to accommodate strands of barbed wire.
The post width is approximately 3 and can be ordered in a variety of lengths ranging form 60 to 96.
View Complete Details

HATBOX RDU UNIT

  • Description Single Coil 30" Concertina Rapid Deployment
  • NSN 5660-01-495-6421
  • DIA. 30"
Maritime, Military and Law Enforcement Rapid Deployment Applications
When every second counts in preventing an act of piracy or impeding an escalating danger, there is simply no substitute for Allied-Maritime Rapid Deployment Units. Our barbed tape barriers are developed to prevent intrusion on any level of security.

Visual and Physical Deterrent
Passive Non-Lethal Counter Measure
Freeboard Deck and Onboard Barrier
Multiple Methods of Deployment
The HatBox is designed for military and police use in varying climates and terrain
conditions. This unit can be rapidly deployed in hallways, stairwells, entrances and exit areas, etc. and quickly recovered for repeated use. Allieds HatBox can be used in both indoor and outdoor applications. Each unit comes with all of the materials and tools necessary for immediate use.

Rapid dispensing anti-personnel barrier provides 50 (15m) of 30 (764mm) diameter barbed tape fabricated from 0.025 (0.64mm) thick 301 austenitic stainless steel strip hardened to Rockwell (30N) 50-55. Clusters of four needle sharp barbs shall be punched 4 (102mm) on center. Barb cluster width shall be 1.210 (31mm). Barbs shall be alternately offset from the tapes centerline 0.15 -0.45 (3.8mm 11mm). Each coil loop shall contain (24) 1 barb cluster.

Adjacent pair of coil loops shall be spot welded together at (5) points of approximate equal spacing about the perimeter in such a way to prevent one slipping passed the other. Weld attachments shall be capable of surviving a minimum pure tensile load of 400# (181 kg).

One jacketed stainless steel wire rope 7 x 7 strand 364 minimum diameter shall be attached to each pair of coil openings at 12 2 (305mm 51mm) 101 coil loops shall cover 50 2 (15.2m 51mm). 16 gauge twist ties, gloves, stakes and tie tool furnished with each unit housed in a fiber case canister (hatbox).

Uses: riot control, crowd control, (impedes movement on stairways, corridors, sidewalks and streets, etc.)

Where Used: embassies, jails, prisons, INS facilities, courthouses, and police departments, etc.
View Complete Details

BARBLESS Rapid Deployment Unit

The Barbless RDU has the same construction as the traditional Triple Strand Rapid Deployment Unit but without any barbs to prevent any harm. The unit acts as a dimensional barrier and visual deterrent. The unit can also be used for signage and advertising. While permanent installations are appropriate the Barbless RDU unit is adaptable to traveling venues as a visual barrier to control crowds.

USES: Agricultural, school events, crowd control barriers, instant physical perimeter deterrent.
View Complete Details

TRIPLE STRAND Rapid Deployment Unit

  • Description Triple Strand RDU with magazine
  • NAT. STOCK NUMBER 5660-01-537-7956
  • DIA. (2)-30" (1)-60"
  • STRIP MATERIAL Galvanized
US Patent No. 7, 909, 309 B2

Allied Tube & Conduits Triple Strand Rapid Deployment Unit (RDU) is a quickly deployed security perimeter appropriate for emerging threats or for a permanent barrier.

With the capacity to deploy 480 of Razor-Ribbon in just two minutes, our Triple Strand RDU takes the place of a large crew working hours in the field. The unit deploys with only two people and removes the potentially hazardous conditions associated with field installation of barbed tape coils.

Rapid Deployment System consists of a stack of one (1) 60 Barbed Tape Coil on top of two (2) 30 Barbed Tape Coils. A network of structural support trusses every 11 add rigidity and allow accessories to be fastened to deployment unit. Additionally support trusses come with provisions for ground stakes and an integral cable system to assist in deployment over any type of terrain. Deployment time is two (2) minutes and retraction time is between 12 to 17 minutes. Deployment length is 480 feet. Package size is 90 high by 62 wide. Ship weight is 2, 100 lbs.

The Barbed Tape is standard galvanized military BTC with galvanized high tensile strength core wire. Coils are fastened together in an alternate loop arrangement to minimize any intrusion attempts.

USES: Economical, simple and reusable system to provide the military, police, municipalities, and commercialindustrial security integrators with instant physical perimeter protection.
View Complete Details

RAZOR-RIBBON FLAT PANELS

  • Panel Size 3-Loop Panel
  • Height 34"
  • Width 120"
RAZOR-RIBBON FLAT PANELS
High security, flanged, wire reinforced panels.

Panel Size Height Width
3-Loop Panel 34" 120"
4-Loop Panel 44" 120"
5-Loop Panel 51" 120"
6 Loop Panel 60" 120"
View Complete Details

RAZOR-RIBBON SINGLE LOOP

  • DIA 18
  • # Loops 100
  • Overlap Spacing 6"
  • Yield 100'-0
RAZOR-RIBBON SINGLE LOOP
Flanged Material in a Single Row
The single flat coils are regularly used in gate installations where traditional barbed tape is used.
View Complete Details

FLAT RAZOR WRAP

  • DIA 18
  • # Loops 133
  • Overlap Spacing 9"
  • Yield 100'-0
Non-Flanged Material
Flat wrap coils add additional security to traditional perimeter fence applications. The Flat Razor Wrap coils provide a neat but effective barrier when used together with mesh fences. Flat Razor Wrap coil installation is particularly simple when it is fitted by overlapping the fence mesh. Economical but effective barrier.
View Complete Details

Ground Stakes

GROUND STAKES
Required to anchor ground based installations, usually positioned at 10 feet intervals.
View Complete Details

COLORED BARBED TAPE

Our color coded barbed tape comes in a variety of colors that can be easily integrated with your fence framework and perimeter security projects.

Our Razor-Ribbon colored barbed tape offers additional protection against corrosion in harsh environments such as Maritime.

Our product comes in a variety of colors such as Yellow, Red, Black, Orange and Army Green. Any industrial or commercial color can be matched.
View Complete Details

HEXARMOR GLOVES

HEXARMOR GLOVES
These gloves were designed specifically for handling barbed tape products. These gloves are cut, puncture and abrasion resistant.
View Complete Details

Hog Rings

HOG RINGS
For fence anchored installations, Hog Rings are used to connect the barbed tape to the fence fabric.
View Complete Details

Hog Ring Pliers

HOG RING PLIERS
Used to compress hog rings in fence anchored installations.

Ground Stakes are required to anchor any ground based configuration, usually at ten feet intervals. The Barbed Tape coil is affixed to the fence fabric with either Hog Rings or Wire Ties. The Hog Ring Pliers or a Wire Tie Twist Tool will be used, depending on the specification, to compress the hog rings or to twist the wire tie. In order to protect the installer, an Arm Guard, covering the hand to the elbow, or a Sleeve Guard, covering the wrist to the shoulder, should be used. Both afford a degree of safety during the installation process. Lastly, Warning Signs are used to alert unsuspecting persons to the imminent danger.
View Complete Details

WIRE TIE TWIST TOOL

WIRE TIE TWIST TOOL
Used to twist wire ties in fence anchored installations.

Ground Stakes are required to anchor any ground based configuration, usually at ten feet intervals. The Barbed Tape coil is affixed to the fence fabric with either Hog Rings or Wire Ties. The Hog Ring Pliers or a Wire Tie Twist Tool will be used, depending on the specification, to compress the hog rings or to twist the wire tie. In order to protect the installer, an Arm Guard, covering the hand to the elbow, or a Sleeve Guard, covering the wrist to the shoulder, should be used. Both afford a degree of safety during the installation process. Lastly, Warning Signs are used to alert unsuspecting persons to the imminent danger.
View Complete Details

Warning Signs

WARNING SIGNS
Used to alert unsuspecting persons of imminent danger.

Ground Stakes are required to anchor any ground based configuration, usually at ten feet intervals. The Barbed Tape coil is affixed to the fence fabric with either Hog Rings or Wire Ties. The Hog Ring Pliers or a Wire Tie Twist Tool will be used, depending on the specification, to compress the hog rings or to twist the wire tie. In order to protect the installer, an Arm Guard, covering the hand to the elbow, or a Sleeve Guard, covering the wrist to the shoulder, should be used. Both afford a degree of safety during the installation process. Lastly, Warning Signs are used to alert unsuspecting persons to the imminent danger.
View Complete Details

ARM SLEEVE GUARD

ARM SLEEVE GUARD
Used to protect the installer, the armsleeve guard covers from the wrist to the shoulder.
View Complete Details

Wire Ties

WIRE TIES
Wire ties are used to secure and anchor installations.

Ground Stakes are required to anchor any ground based configuration, usually at ten feet intervals. The Barbed Tape coil is affixed to the fence fabric with either Hog Rings or Wire Ties. The Hog Ring Pliers or a Wire Tie Twist Tool will be used, depending on the specification, to compress the hog rings or to twist the wire tie. In order to protect the installer, an Arm Guard, covering the hand to the elbow, or a Sleeve Guard, covering the wrist to the shoulder, should be used. Both afford a degree of safety during the installation process. Lastly, Warning Signs are used to alert unsuspecting persons to the imminent danger.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Razor Ribbon)
  • Harvey, IL 60426 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/razor-ribbon/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0007457888{main}( ).../index.php:0
20.02482060984include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.03632783544include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.04433719232header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice