Our Products #4992557

FeaturesApplications These NEMA 1213, IP65 contact blocks are designed for use on ALL REES push button operators and selector switches as shown on the preceding pages. The mechanical life of these devices is 1, 000, 000 operations. Each captive terminal on the contact block will accept (2) # 14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing.

The following switches are hand operated, control circuit devices, rated Heavy Duty normally for use with electromagnetic equipment. The cover, painted with a dry powder paint, and the chrome platedpainted plunger are made from die-cast zinc. Each captive terminal will accept (2) #14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing. Each switch is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 1, 000, 000 operations.These switches can be found on a variety of machines such as punch presses, press brakes, and spot-welding equipment as RUN or START buttons. Their rugged construction and long term reliability make these switches extremely well suited to function within various environments.

These switches are slack cable style with Slow-Make contacts. The switches are not Positive Transfer and they do not latch in any position. They should NOT be used for any Emergency Stop applications. The action of these devices is that when the switch actuating arm is pulled by a cable the switch contacts will change state, that is, the NO will be closed and the NC will go open. When the force on the cable is removed from the actuator arm, spring pressure will return it to its normal position, while the contacts are held in position through a ratchet mechanism. The next time the cable is pulled, the action is repeated with the contacts returned to their original state. The housing and cover are made from a glass filled black polycarbonate. The mounting base and double end actuator arm are die cast from a high strength zinc alloy. All exterior steel components are made from #303 Stainless. Switches are provided with two 12 NPT conduit openings. The total maximum cable length recommended is 200 feet with a maximum interval support of 10 feet. The life of these devices is in excess of 150, 000 mechanical and 1, 000, 000 electrical operations. Each captive terminal on the replaceable block will accept (2) #14 AWG stranded wires and the contact are gold plated to eliminate high resistance tarnishing. These devices can be found on various conveyor installations as well as other stations that require the pull-on, pull-off function that this being provides. Their rugged construction and long term reliability make these cable switches extremely well suited to function within various industrial environments.

switches are hand operated, control circuit devices, rated Heavy Duty normally for use with electromagnetic equipment. The body, painted with a dry powder paint, is made from die-cast zinc. The plunger head is powder painted or chrome plated die-cast zinc. The plunger head of the 04662 is plastic. Each captive terminal will accept (2) #14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing. Each switch is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 1, 000, 000 operations. These switches can be found on a variety of machines such as punch presses, press brakes, and spot-welding equipment as RUN, START or STOP buttons. They are also used on transfer machines. The 04662-002 complies with standards for emergency stop applications. Their rugged construction and long term reliability make these switches extremely well suited to function within various industrial commercial environments.

switches are hand operated, lockable, control circuit devices, rated Heavy Duty normally for use with electromagnetic equipment. The bodies are made from die-cast zinc, and painted with a dry powder paint. Each captive terminal will accept (2) #14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing. Each switch is supplied with mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 500, 000 operations. These switches can be found on a variety of machines such as: punch presses and press brakes as START and STOP or FORWARD and REVERSE buttons and with material handling equipment as UP and DOWN or RAISE and LOWER controls. The rugged construction and reliability of these switches makes them extremely well suited to function within various industrial commercial environments. The padlock slide latches the red plunger in the depressed position.

The following switch is a hand operated, control circuit device, rated Heavy Duty normally for use with electromagnetic equipment. The body is die-cast zinc. The chrome plated knob and plunger are also made from die-cast zinc.

Nema 1213, IP 65

Each operator will accept up to three tiers of two contact blocks for a total of six separate circuits. Each operator is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of this unit is 250, 000 operations.

A selector-push button operator combines the function of a single push button device with that of a selector in a single unit. Contact operation sequences are selected by rotating the knurled guard in the two available positions. When the position is selected, depressing the plunger will give contact operation as shown in the sequence chart.

each captive terminal will accept (2) #14 AWG stranded wires. Each switch is supplied with a fibreflex gasket which provides an oil tight seal upon installation. For added protection against corrosive environments a neoprene gasket is available as an accessory item by ordering part number 02005-540.

There are two NPT conduit openings. The maximum cable recommended cable length is 200 feet with a maximum interval support of 10 feet.

The mechanical life of the switch is 150, 000 operations.

This switch can be installed on various conveyor installations and provides a constant access for emergency or normal stopping.

slack cable style, bi-directional switch 2 NO and 2 NC contacts. The housing is made from high quality die-cast aluminum and powder coat painted yellow. The covers are made from aluminum and also powder coat painted yellow.

This switch is activated by pulling the cable on either side. The switch can only be activated by pulling on the cable one side at a time (not simultaneously). Pushing the blue reset button on the switch cover will reset the contacts.

Manual reset
Gold plated contacts eliminate high resistance tarnishing
Nema 1213, IP 65
Can be mounted in any position

Each captive terminal will accept (2) #14 AWG stranded wires. Each switch is supplied with a neoprene gasket which provides an oil tight seal upon installation.

There are three NPT conduit openings. The maximum cable recommended cable length is 200 feet on each end with a maximum interval support of 10 feet.