Post Buy Requirement
SM
United States
Add Review

Other Products / Services

Metallic Scum Skimmer Pipe Assembly

HMAX Non-Metallic Scum Skimmer Pipes feature a tube of FRP with a gel coated interior for easy release of grease or solids, limiting build-up. Wall bearings are made of long lasting UHMW-PE material. Lightweight, easy to install this scum pipe will eliminate all corrosion and unsightly build-up, common with carbon steel and even stainless steel pipes. Available with:

Lever Actuation
Mechanical Actuation
Handwheel Actuation
View Complete Details

Bibbigard Torque Limiter

Bibbigard Torque Limiters feature Stainless Steel construction providing years of steadfast service and reliability. Replaces existing standard shear pin sprocket arrangements without any modifications.

Available either pre-set (non-adjustable) or adjustable.

Simply dial-in the torque level required and the assembly is ready for use.

No Shear Pins to Replace
Simply reset the trip assembly with tap of hammer or mallet
No Corrosion
View Complete Details

Metallic Chain

  • SERIES NM 720S
  • Weight 1.6 lbs. per ft.
SENQCIA MAXCOs latest generation of non-metallic 6" pitch collector chain features many enhancements to insure a long productive life in a wide range of applications and service conditions. Manufactured of Acetal Resin, the chain link has a smooth finish with a very generous cross-section. The pin press-fits into the sidebar with a "T" head interlocking arrangement and is secured without the use of pins or cotters.
Link Material: Acetal Resin
Pin Material: Reinforced Nylon
Pitch Length: 6"
Working Load: 3, 100 lbs.
Ultimate Strength: 7, 500 lbs.
Weight: 1.6 lbs. per ft.
Available Attachments: F-228 F-226

Snap Tight Pin, insures positive locking every time, easy to remove.
Chain Saver Sidebars, extends life of chain and sprockets,
Available from Stock, supplied with F-226 or F-228 attachments.
View Complete Details

Cast Nylon Headshaft Bearing

  • Size 1-15/16" bore to 4-7/16
Featuring a Cast Nylon body with oil filled nylon bearing inserts. Self-aligning, split design allows for bearing replacement without removing shaft. Metallic shaft does not come into direct contact with the bearing material as a thick sleeve of non-metallic material is mounted on shaft ends, extending service life by providing low friction contact surfaces between shaft and bearing.

Available from 1-1516" bore to 4-716" bore. Contact SENQCIA MAXCO for additional details or sizes.

Cast Nylon Body
UHMW Shaft Sleeve
Oil Filled Nylon Bearing
Simple to Install
Zero Lubrication Required
View Complete Details

Drive Chain

  • SERIES NH 78
  • Avg Ultimate Strengh 4, 000 lbs.
Pitch: 2.609"
Working Load (Max): 1, 750 lbs.
Avg Ultimate Strength: 4, 000 lbs.
Material: Link: Acetal
Pin: 304 SS
Sprocket: 78 Series (Metallic or Non-Metallic)
Weight: 4.0 lbs. per ft
View Complete Details

Hybrid Sprockets

SAV Hybrid Sprockets feature a hardened stainless steel tooth segment attached to a steel plate sprocket hub. Unlike typical segmented tooth sprockets where entire sections of the sprockets are disassembled, each individual tooth segment is replaced, making installation and replacement easy to perform with minimal effort.

Precision shape, each segment is formed and checked for accurracy within extremely close tolerances.

SAV Hybrid Sprockets are available in standard sprocket sizes for drive and idler locations. Exceptionally economical, the SAV Hybrod sprocket is the smart choice for use with SAV stainless chain.

Non-Metallic plate sprocket hubs are available for idler shaft locations with sleeve bearing hubs for added low friction enhancement of your collector system.
View Complete Details

Flight Monitoring System

  • SERIES HMAX
The action of the armature being rotated due to the travel of the flight causes the ceramic magnet to sweep past the sensor tripping the sensor and sending a signal to the PLC or SCADA system. The system can be programmed to assess for loss of motion, chain elongation, and asymmetrical chain or flight conditions (chain jump on one side) sending an alarm when warranted.

The armature target arrangement eliminates the need for attaching targets on each flight, insures absolute correct alignment between sensor and target, cuts down on nuisance alarms.
View Complete Details

Aluminum Flight

  • Lightweight 2.36 Lbs per ft
Environmentally friendly. The Aluminum Flight from SENQCIA MAXCO is the easiest flight to install as it eliminates drilling or notching and does not require filler blocks. Available in two styles, Regular (perfect for tank widths up to 24 ft) and Heavy Duty for tank widths of up to 40 ft! An optional neoprene extrusion slides into the slotted track for use as a squeegee and with just 6 locking plates to mount the extrusion installation is done in just minutes.

The Aluminum Flight is for use with non-metallic or metallic chains. Perfect for high load collectors or where grit is a problem.

Extruded T5 - 6063 Aluminum
Patented Attachment Method Eliminates Drilling, Notching Flights
Simple to Install Adjust
Environmentally Friendly - Recyclable
Lightweight - 2.36 Lbs per ft
View Complete Details

Stainless Steel Chain

  • SERIES HB 78
  • Weight 3.8 lbs. per ft
FEATURES: Superior resistance to wear and corrosion of any 78 series chain. Stainless steel construction offers high load, chemical and corrosion resistance and extremely minimal stretch, especially when compared to non-metallic NH-78 style chains. Toughest chain for the harsh extremes of clarifier drives and similar applications. Economically priced this chain is ideal for clarifier, bar screen and grit collectors, a direct replacement for H-78 and NH-78 chains.

Pitch: 2.609"
Working Load (Max): 3, 300 lbs.
Min. Ultimate Strength: 21, 000 lbs.
Material: 403 Stainless Steel (Hardened)
Sprocket: 78 Series (Metallic or Non-Metallic)
Weight: 3.8 lbs. per ft
View Complete Details

Wear Shoes

  • SERIES ASTM G-65)
HMAX UHMW-PE Wear Shoes are designed for use in our standard, state of the art HMAX rectangular system and standard wear shoes applications. This material has been shown to be superior to all other typical wear shoe materials (based on ASTM G-65). Wear Shoes are also available in different materials;

Polyurethane
Cast Nylon
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Senqcia Maxco, Ltd.)
  • Kennesaw, GA 30152 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/senqcia-maxco-ltd/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0007457888{main}( ).../index.php:0
20.02082020344include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.26312742488include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.26913678184header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice