Solaronics, Inc.

United States

The flame produced by the burner heats the combustion chamber and heat exchanger(s) and causes them to reach temperatures in the range of 200° to 1000° F. Infra-red generated is in the range of 300 to 6500 BTUHft2 thus the term low intensity. The combustion chamber is made of 14 or 16 gauge aluma-therm steel. The heat exchangers are made of 12 gauge black steel or 16 gauge aluminized steel. Both provide 1.052 per square feet of radiant surface per linear foot. The last heat exchanger in each system incorporates a spiral turbulator for increased efficiencies. The 10, and 5′ sections are joined by standard compression coupling tube clamps. These clamps are made of two layers of 18 gauge (0.052″) aluminized steel. The inner sleeve has precision meshing teeth for even draw and pressure. Each tube clamp is closed with three 58″, 651b. torque, zinc plated carriage bolts. A #5 malleable iron turnbuckle-58″ eye to eye is also standard.

Proven system design – over 40 years with more than 3 million burners placed in service. Instant heat on demand: reaches maximum operating temperature in less than 1 minute. No direct venting required: less roof penetrations. May be used in protected outdoor environments. Operates on Natural or LPPropane Gas Factory pre-wired, pre-piped and tested. Highly polished mirror brite aluminum reflectors for maximum efficiency. Corrosion-free aluminized steel main frame. CSA International Design Certified to ANSICGA Standards 2-Stage Models Available 2-Stage operation based on ambient temperature variations. Eliminate excess heat when not needed. Capable of fast recovery when temperatures fall. Optimum combustion in both operating stages. Air and gas ratios are precisely matched for efficient, fuel saving operation. 24-volt input for lower installation costs.

Solaronics gas fired infra-red Suntube systems are ideal for any commercial or industrial building. Inlet air capabilities make them particularly well adapted for buildings with high negative pressure or airborne contaminants such as dust, over-spray and degreasing fumes. Directly vented units are an ideal choice for buildings with low infiltration or where condensation is a problem. Although not explosion proof, Suntube has no open flame. Solaronics gas fired infra-red Suntube systems are avail able in many different input capacities, system lengths and configurations. AGA and CGA design certified heater capacities are 40, 000 thru 200, 000 BTUH every 5, 000 BTUH. They are available in 10, 20′, 25, 30′, 35, 40′, 45′, 50′, 55′, 60′, 65′, and 70′ system lengths in both straight and compact U-tube configurations. Each system comes factory preassembled in 5′ or 10′ long sections to eliminate loose hardware and for ease of field installation. Suntube is design certified for either directly or indirectly vented operation and for use with inside or outside combustion air.

CSA International Design Certified to ANSICGA Standards Compact size: Fits standard 2 feet x 4 feet ceiling panel grids Low clearances to combustibles Pre-assembled: Just hang and connect Simple chain hanging arrangement Multi-poise mounting: Horizontal to 45° Mirror Brite highly polished reflector for maximum reflectivity Corrosion resistant: All aluminized steel Natural or Propane Gas Positive pressure intermittent blower with pre-purge and post-purge cycles Screened inlet air opening Indoor or outdoor combustion air through wall or roof Vented or unvented exhaust 20 feet maximum linear (straight) length of vented exhaust (One 3-inch elbow = 5 linear feet) Dry operating: no condensation of flue products during steady-state operations Control Package and Burner 120 VAC – 1 Phase – 60 Hz Factory wired 36-inch long, 3-prong electrical power cordset Replaceable Panel Fuse, 610 A – No tools required Burner observation port for flame and ignition 24 VAC – 1 Phase – 60 Hz thermostatic control External terminal board for easy field wiring of thermostat Pre-purge time: 15 seconds. Post-purge time: 120 seconds Direct spark ignition: 100% safety shut-off All controls enclosed in removable control package

DOORJET heaters are designed to be operated only when the door is opened. It is NOT designed as a make-up air heater. Car Washes Warehouses Manufacturers Auto Body Shops Distribution Centers Maintenance Facilities Marine Repair Facilities Minimum Inlet Pressure Natural and LPPropane Gas: – 550, 000-750, 000 BTUH – 7 inches WC – 850, 000-950, 000 BTUH – 8 inches WC Maximum Inlet Pressure Natural Gas and LPPropane Gas: 14 inches WC 1 inch NPT Gas Inlet Minimum Mounting Height A DOORJET should be mounted 6 inches above the height of the door. Minimum Mounting Height is 12 feet – 6 inches. Mounting below the minimum height would require careful consideration of human safetycomfort and property damage factors and would be the responsibility of the owner and installer.

The flame produced by the burner heats the combustion chamber and heat exchanger(s) and causes them to reach temperatures in the range of 200° to 1000° F. Infra-red generated is in the range of 300 to 6500 BTUHft2 thus the term low intensity. The combustion chamber is made of 14 or 16 gauge aluma-therm steel. The heat exchangers are made of 12 gauge black steel or 16 gauge aluminized steel. Both provide 1.052 per square feet of radiant surface per linear foot. The last heat exchanger in each system incorporates a spiral turbulator for increased efficiencies. The 10, and 5� sections are joined by standard compression coupling tube clamps. These clamps are made of two layers of 18 gauge (0.052�) aluminized steel. The inner sleeve has precision meshing teeth for even draw and pressure. Each tube clamp is closed with three 58�, 651b. torque, zinc plated carriage bolts. A #5 malleable iron turnbuckle-58� eye to eye is also standard.