SprayWorks Equipment Group, LLC.

If you are just starting out, or need a rig that’s more suited for smaller job requiring a low-output, you may consider an air-driven spray insulation machine. These machines are common among entry-level contractors and startups or residential insulation contractors, primarily because they are cost-effective for businesses. Air-driven machines offer efficiency and affordability for a variety of jobs, and deliver a mix of performance and value. SprayWorks has an expansive line of air-driven spray foam insulation machines, so you can choose the one that’s right for your job and business. These machines need an air compressor, which makes them ideal for use in plants where on-site compressors already exist. Air-driven insulation foam machines can offer outputs of up to 30 lbsmin, and a pressure rating maximum of 3, 000 psi. The higher-pressure machines are recommended for use in coating applications. The common standard for heating capacity in air-driven spray foam machines ranges between 6 to 15 kW, depending on the type of application that the proportioner is used for. The pneumatic technology in which these air-driven rigs are based on is known to be reliable, as it has been in use for decades. It employs the simplest technology of using a single motor to power two pumps. These machines are considered easy-to use, as the applicator trigger is designed to maintain a consistent pressure ration when squeezed.

SprayWorks offers the PMCA Classic Series, which are low-pressure spray foam machines configured with a horizontal pump line. This design ensures even loads during the pumping cycle. SprayWorks offers the PMCA Classic Series, which are low-pressure spray foam machines configured with a horizontal pump line. This design ensures even loads during the pumping cycle. Great for use in a variety of plural component foam and polyurea coating jobs, they are equipped with digital controls so you can precisely monitor and adjust the temperature depending on the component being sprayed. When used with other PMC accessories, such as the Temperature Sensing Unit (TSU), the PMCA spray machine can deliver accurate temperature for efficient application under a range of conditions. The Classic Series is a small footprint machine that is compact and easy to transport between job sites. SprayWorks has two different PMCA insulation machines, depending on the job type – from spray foam insulation to polyurea coatings.

SprayWorks offers several hydraulic spray foam insulation machines to choose from, depending on the needs of your job. Hydraulic foam insulation machines are appropriate for a variety of jobs from residential construction to large commercial buildings, roofs, roads, bridges, and parking decks. Hydraulic proportioners have a longer life span than traditional electric spray insulation machines, lasting between 10 and 12 years on average, and even longer when properly cared for and maintained. Hydraulic foam machines have large pumps which cycle less frequently than other types of machines, which means, they don’t need to be replaced as often. Generally, these pumps last one to two years because the output per stroke ratio is much higher. The fluid-driven component of hydraulic machines makes these spray foam insulation rigs to be the most efficient in design and performance, as some proportioners can reach 3, 500 psi.

Design: Simplified heavy duty design components have longer life span and are inexpensive to replace, providing the best value over other designs! Rapid Trigger Response: Easy to access, straight forward air ports and short trigger stroke allows for a very powerful and accelerated rapid trigger response action, ensuring immediate spray pattern development! Crossover Protection Design: Purge air check valve eliminates cross over material in the air cylinder and trigger handle assembly! PCT Precision Air Flow Design: Reduces rapped build up in front of the spray tip orifice! Multiple PCT Nozzles: Round Spray, Flat Spray, PourCast, and Extension Tip Spray (Known as the Blaster) for the hard to reach areas specifically engineered for the interior spray foam insulation market! Universal Manual Valves: Manual Valve assembly adapts to existing types of coupling block assemblies! Manufacturer’s 1 Year Warranty: PMC proudly stands behind their product lines and provides the industry’s best service and support! Newly Designed Mixing Chambers: Ball and socket connection makes for fast change out and elements set screw assemblies! Quick change PCT (Pattern Control Tip): Allows the contractor to change spray pattern size without disassembly of the spray gun, giving the spray applicator more precise application combinations! Mixing Chamber and PCT Combination: Advance design for pattern development and mixing provides superior atomization! Fluid Block: Easy access fluid block makes the mixing chamber change out a breeze! Easy Access A & B Filters: Easy to clean filters with multiple size screen mesh options allow for more consistent material flow for different types of material viscosities! Universal Coupling Block: Quickly adapts to existing types of coupling block assemblies and easily adapts to other types of spray foam and polyurea equipment! Made in the USA! DOWNLOADS: