Plastic Ball Bearings in USA

YOU ARE IN : USA / Industrial Supplies / Bearings And Bearing Components / Plastic Ball Bearings

View 82 Products below

  • Self-aligning Ball Bearings

    • degrees : 4 to 7

    This type of ball bearing is recommended when alignment of the shaft and housing is difficult and the shaft may flex. The outer ring has a spherical raceway and its center of curvature coincides with that of the bearing; therefore, the axis of the inner ring, balls and cage can deflect to some extent around the bearing center. Pressed steel cages are usually used. Since the contact angle is small, the axial load capa More...

    Baldwin Supply Co.

    | More...

  • Ors Sealed Radial Ball Bearing

    • Minimum Qty : 1 10

    Item: Radial Ball Bearing, Bearing Type: Sealed, Bore Dia.: 10mm, Bore Tolerance: +0-.0080 mm, Outside Dia.: 30mm, Outside Dia. Tolerance: +0-11 micro, Width: 9mm, ABEC Tolerance: 1, Dynamic Load Capacity: 1, 220 lb., Static Load Capacity: 530 lb. , Max. RPM: 34, 000, Temp. Range: -40 Degrees to 212 Degrees F., Bearing Material: Steel, Cage Material: Pressed Steel, Seal Material: Synthetic Rubber, Lubrication: EM Gre More...

  • Idler Roll End Ball Bearing

    • FD : 50mm
    • OD : 47mm
    • Bore : 12mm
    • Suitable For : 50mm Dia.
    • POBCO Part# : LDTP50mm12mm

    Black Thermoplastic Housings (conductive polypropylene) with precision chrome shielded bearing offer higher load and higher speed capabilities and quiet operation. More...

    Pobco Plastics

    | More...

  • Ball Bearings

    • Sizes : 1-15/16 inches (49 mm)

    Ball Bearings Request Information Our ball bearings are backed by more than 70 years of manufacturing and technical expertise, and we offer the widest range of duty and performance options, along with many housing, seal and mounting choices. With a legacy of performance and quality, Link-Belt ball bearings are trusted leaders when you need a ball bearing that will lend uptime, quality and performance to your applicat More...

  • Swivel Shackle Slotted Head Pin Ball Bearing

    • Categories : Stainless Steel Rigging, Swivel Shackles.

    SKU: RF75. Categories: Stainless Steel Rigging, Swivel Shackles. A : 7.9 mm B : 17.0 mm C : 60.0 mm D : 15.8 mm P.L. B.L. : 2100 kg U.D.L. B.L. : 2300 kg Shackle Pin Product No. : - Weight : 80 g

  • Angular Contact Ball Bearings

    • Standard Designs : 6000 Series Deep Grouve Ball Series - including self-aligning inner race 7000 Series Angular Contact - single and matched pair Type QJ Four-Point Contact

    Radial & Angular Contact Ball Bearings ERIKS has a unique blend of application experience in ball bearing applications that span the use of heavy-duty applications such as power transmission to the employment of precision class angular contact ball bearings in optics-gimbal assemblies. The design and integration of bearings into the use of motor and geartrain is also a core competency of ours. Let us help you with yo More...

  • Post your Buy Requirement

  • Ball Thrust Bearings

    • Thickness (in.) - C : .448 - .458
    • Model No. : H-19B

    At ART Technologies, our focus is on the customer. We provide rapid, effective and highly competitive solutions for your Thrust Bearing needs. ART Technologies offers an extensive line of high quality ball bearings for your applications. Our bearings are manufactured in the USA at our facility in Hamilton, OH. We ship these bearings to seven different countries maintaining competitve pricing. More...

    Art Metals Group

    | More...

  • Instrument Ball Bearing

    • OD Fraction : 3/16"
    • Bore : 0.0937
    • Bore Fraction : 3/32"
    • W Fraction : 1/16"

    Rainbow Precision Products has a large selection of miniature bearings and instrument series ball bearings with many types available. Precision tolerances from ABEC-1 through ABEC-9 are generally available for most miniature applications. Bore sizes of miniature ball bearings start at 1 mm with an outside diameter of 3 mm More...

  • Thrust Ball Bearing

    • Size range: : 228.6 mm to 1371.6 mm

    Type TVL-Angular Contact Thrust Ball Bearing Type TVL thrust ball bearings provide exceptionally low friction, cool running and quiet operation at high speeds and also are less sensitive to misalignment. We designed TVLs for thrust loading, but it will also accommodate some radial loading. Size range: 228.6 mm to 1371.6 mm (9 in. to 54 in.) Design Attributes: Precision ground and lapped steel balls are enclosed by ha More...

    Timken Drives Llc

    | More...

  • Precision Metal Ball Plastic Bearings

    Friction, or resistance to motion, is the result of the force acting between two surfaces as they slide against each other. Bearings reduce friction and provide smooth sliding contact between surfaces due to their material, shape or lubrication. Choosing the correct bearing for an application improves efficiency, extends bearing life at high speeds and avoids overheating. Bearings fall into two general categories: ra

  • Precision Ball Bearings

    Precision Ball Bearings A precision ball bearing is chosen in an environment where the bearing can not be routinely lubricated or there may be environmental debris. The precision ball bearing offers easy rolling motion and bearing protection. Two per wheel are used.

    Bond Casters

    | More...

  • Ball Thrust Ball Bearings

    Thrust bearings are designed to handle axial loads while operating at high speed. Bearings are composed of bearing rings with raceway grooves for the balls. Double direction thrust ball bearings can support axial load in both directions. Neither style can be subjected to radial loads. Available in bore dimension range from 10mm to 560mm.

    Action Bearing

    | More...

  • Self Aligning Ball Bearings

    Self-aligning ball bearings have a spherical outer ring raceway, the center of whose curvature meats that of the bearing itself, so that the inner ring, ball and cage continue to rotate, aligning themselves if they have become misaligned within design limits. This type of bearing is suitable when the displacement of the centers around which the shaft and housing rotate and shaft deflection are likely to occur. Someti

  • Thin Section Ball Bearings

    RBC Aerospace Bearings offers a full line of standard and many specialty and custom designed thin section ball bearings to the aerospace industry and all major OEMs. RBC’s thin section ball bearings are offered in radial contact, angular contact, 4-point contact and sealed radial contact designs. These bearings are offered in ABEC 1 through ABEC7 precision grades, pre-loaded, corrosion protected, grease-lubricated,

  • Ball Bearings

    PIB offers the 600 Series miniature metric sizes ranging from 5 to 9mm bore diameter. They are available in open and shielded in either chrome steel or stainless steel material.

    Pib Bearing, Inc.

    | More...

  • Angular Contact Ball Bearings

    Large Selection of Miniature Instrument, Plastic, Radial, Angular and Single Row Type Ball Bearings Ball bearings are used widely in instruments and machines in order to minimize friction and power loss. While the concept of the ball bearing dates back at least to Leonardo da Vinci, their design and manufacture has become remarkably sophisticated. Commercially available ball bearings, which are usually made from hard

  • Engine Ball Roller Bearings

    box and engine ball bearings are offered as radial, angular contact, single or double row, can be supplied as pairs or sets, and are offered with bore sizes from 1 inch to 25 inches. These bearings are offered as ABEC 1 through ABEC 7 precision grades, pre-loaded, corrosion protected, grease-lubricated, and are available with numerous separator, ball, shield, seal, and lubrication options. RBC’s gear box and engine

  • Post your Buy Requirement

  • Thin Section Ball Bearings

    Welcome to RBC's on-line Engineering Data Guide for Thin Section Ball Bearings. TO access critical dimensions and data for your design questions, use the Seach By Criteria section below. If you are uncertain as to which of RBC's Thin Section Ball Bearings is best suited for your design application, check with our selection guide. To view an entire product series, select a product from the table of contents.

  • Ball Bearings

    With more than ninety years of manufacturing expertise in ball bearings, NTN offers one of the industry’s widest arrays of products to fit your application. ball bearings are available to you off-the-shelf, in sizes ranging from 10 mm to 320 mm outside diameters. And with a virtually limitless variety of configurations of seals, shields, lubricants, internal clearances, and cage designs, there’s no reason to go a

  • Precision Metric Ball Bearings

    Nordex has a large inventory of Miniature Precision Ball Bearings available in Metric and Inch Sizes. 400 Series stainless steel and chrome steel bearings are available in ABEC 1, 3, 5 and 7. Standard sizes available from stock – 1, 5mm to 12mm internal diameter with an outer diameter of 5mm to 28mm (Please inquire for unlisted sizes)

    Nordex, Inc.

    | More...

  • Metric Ball Bearings

    Metric Product Offerings metric ball bearings To complement our broad range of stainless steel (440C) precision miniature & instrument ball bearings in standard inch sizes, we offer a select series of metric ball bearings, also manufactured at our Troy, NY production facility. A variety of special features, including flanges, modified dimensions, and duplex designs are offered in all types of metric ball bearings. Op

  • Deep Groove Ball Bearings

    EBC offers a complete range of single row ball bearings, double row ball bearings and specialty ball bearings. Many sizes are available in stainless steel for wash-down and corrosive environments.

    Ebc Bearings

    | More...

  • Airframe Control Ball Bearings

    RBC offers a full line of airframe control ball and roller anti-friction bearings to the aerospace industry. RBC airframe control bearings conform to SAE-AS7949 (formerly MIL-B-7949) and all major OEM specifications. These bearings are of lightweight design, corrosion protected, grease-lubricated, and typically sealed. Airframe control bearing rings and balls are made of hardened bearing alloy, AISI 52100, with all e

  • Butt Hinge Ss Ball Bearing

    Austral fire specialise in the supply and installation of fire safety packages to any structure whether being new or refurbished. Our qualified and experienced team of tradesmen have certifications in the supply, installation and maintenance of any fire protection package within australia.

    Austral Fire

    Longboat Key | More...

  • Ball Bearings

    NHBB manufactures standard and custom designed ball bearing solutions for a myriad of aerospace, defense, dental, high tech, and medical applications. Our product lines feature inch and metric series ball bearings ranging in size from 0.1250 in. to 11 in. O.D. The following product families are described below: miniature & instrument ball bearings , dental bearings, hybrid ceramic bearings, large aerospace ball beari

  • Shuster Ball Bearings Highest Quality Standards

    SHUSTER BALL BEARINGS ~ HIGHEST QUALITY STANDARDS Rely on Shuster for value-added bearing solutions, including a full line of Radial Ball Bearings. Shuster delivers outstanding quality at a competitive price, providing you with exceptional value no matter what the application. All Shuster radial ball bearings are produced from high quality, through hardened bearing steel with super finished raceways. Automatic assemb

    Shuster Corp.

    | More...

  • Large Ball Bearing

    large diameter precision ball bearings are engineered to perform in life-critical commercial and military aircraft applications. The line includes radial, angular contact, gothic arch, and fractured race construction types in sizes up to 11.024 in. O.D. Our customized solutions feature elements that satisfy a multitude of mounting and operating requirements. Options include special alloys, case hardened rings, extend

    Nhbb

    | More...

  • Angular Contact Ball Bearings

    Designed for high accuracy and excellent high-speed performance. Angular contact ball bearings are designed to carry combined loads: both axial and radial. Angular contact bearings are designed such that a contact angle between the races and the balls is formed when the bearing is in use. The major design characteristic of this type of bearing is that one, or both of the ring races have one shoulder relieved, or high

  • Ball Bearings

    Bearings for high speed, low speed and oscillation applications Many different materials available to optimize performance and reduce cost, such as low carbon steels, 12L14, 1215, 1008, 1010, 1117, 8620, 52100, aluminum, bronze, 303 SS, 440SS, as well as many types of plastics Specialized anti-corrosion finishes and coatings for different application environments, such as trivalent zinc, zinc nickel, black oxide, nic

    Kilian Mfg. Corp.

    | More...

  • Ball Bearings

    Bearings Limited offers a wide variety of radial and angular contact ball bearings, as well as linear motion bearings and a complete line of spherical plain bearings (ball bushings). Popular bearing sizes are available in both premium and secondary brands, giving distributors multiple options for filling their customers' needs – all with a single purchase order.

    Bearings Limited

    | More...

  • Ball Bearings

    Available in a variety of standard and custom inch and metric sizes, our thin section bearings offer high performance in corrosive and non-corrosive environments where space devoted to bearings is at a minimum.

  • E Series Thrust Ball Bearing

    They are used in a variety of medium duty axial load applications. These include pumps, valves, machine spindles, rotary tables, and drilling heads to name a few. ADVANTAGES Inch ABMA standard sizes dimensionally interchangeable with Aetna F series Banded design offers contamination protection Full ball complement for high durability Grooved hardened, precision raceways Single direction

  • Ball Bearing

    For the smoothest and quietest operating drawers take a look at Custom Service Hardware’s selection of ball bearing slides. These slides ride on ball bearings that provide smooth and quiet operation. They also typically have a release that allows for easy drawer removal, which makes for easy cleaning and repair.

  • Mounted Ball Bearings

    A modular bearing assembly consists of sealed and lubricated inch or metric ball bearings. It is contained within a variety of housings types, locking mechanisms, mounting styles, and housing materials.