Worm Drive Clamps in USA

YOU ARE IN : USA / Construction / Building Hardware / Worm Drive Clamps

View 9 Products below

  • Worm Drive Clamp - Hex-head Screw Is Stainless Steel

    • SHORT DESCRIPTION : 9.0 - 22.0
    • BAND DIMENSION : 1/2 inch

    The Oetiker 177 Series Worm Drive Clamps comply with DIN 3017. They are designed with an embossed clamp band and have a large clamping range with high holding force. Due to the short housing saddle there is uniform radial load with a good seal. This design has a weld-free body connection for a secure connection and corrosion resistance. The 177 series has specially formed strip edges that reduce the risk of damage to More...

    H.w. Eckhardt

    | More...

  • Stainless Worm Drive Clamps

    • Thickness : 5/16"
    • Size Range : 7/32" to 5/8
    • Description : Hose Clamp, Stainless 5/16" Band, 7/32" to 5/8" Range
    • Material : Stainless Steel

    Stainless Worm Drive Clamps are an easy, corrosion resistant method of installing fittings in low and medium pressure hose connections. Installation is as simple as selecting the appropriately sized clamp, and tightening with a hex or slotted screw driver. FEATURES Tighten with Hex or Slotted Screwdriver Packaged in Quantities of 10 Made in USA More...

  • Miniature Worm Gear Clamp

    • Weight Lb : 0.0140
    • Material : SAE 300 Series Stainless Steel
    • Width : 5/16"

    Part Number MAH10 Style Style MAH Material SAE 300 Series Stainless Steel Component Material Stainless Steel screw Hose OD From 3664" (14.3mm) Hose OD To 1-464" (27mm) Width 516" Torque 15 in. lbs. Optional PkgBox Qty 10 Weight Lb 0.0140 Meets SAE J1508 Construction Screw design: 14" slotted hex head SAE 300 Series Stainless Steel band, housing and screw More...

  • Worm Gear Clamps

    • Weight : 0.0480
    • SKU : ci-6512-00105408
    • Standard Pack Qty : 200

    Buy Worm Gear Clamps, HS Series by Dixon , SKU: ci-6512-00105408 - Dixon’s worm gear clamps are made with four-piece construction that includes a 516” slotted hex head and a bandhousing made of SAE 201301 stainless steel. The maximum torque for each clamp is 50 in.lbs., and they are packaged 10 to a box. Style HS has a screw that is hade of SAE 1018 case-hardened steel, zinc plated and chromate dipped. More...

  • Embossed Non Perforated Worm Drive

    • Range of Adjust : 8-12
    • Installation Torque (in-lbs) : 25.0

    Embossed worm gear clamps meet or exceed the DIN 3017 standard. Sometimes called worm drive clamps, they have a general purpose non perforated band especially suited for clamping soft silicone hoses. Murray embossed clamps are designed for silicone rubber and other soft hose to protect against shearing and fray. Material grade and sizes are stamped on the band. Currently available in all 304SSW4 and in 316SSW5 stainl More...

    Murray Corp.

    | More...

  • Stainless Steel Worm Gear Hose Clamps

    IQE supply stainless worm drive hose clamps. They are ideal for pluming pipe clams, electrical pipe clams, garden hose clams and agricultural irrigation pipe clams. IQE hose has a smaller Closed Diameter comparing to the same SAE size clams, which makes more flexible and convenient at job sites. With hose band fully notched, you can all the way tighten to the end. Hose band partially notched Stainless Steel Worm Driv

    Iqe, Llc

    | More...

  • Post your Buy Requirement

  • Worm Drives

    Our worms are available in coarse and fine pitches. Outside diameters range up to 6 inches and worm lengths range up to 12 inches. Avon can reverse engineer a worm or worm gear set when necessary. Worm drives can help decrease speed and allow higher torque to be transmitted. A gearbox using worms and worm gears will be more compact than one made from most other gear options.