Post Buy Requirement
TM
United States
Add Review

Our Products

Column Clamps PDF

  • Bolt Length 5-1/2”, 6”, 6-1/2”, 7-1/2”, 9”, 13”
  • Column Flange Width 5”, 8-1/2”, 12-1/2”
Accommodates I-Beam Flange Thickness up to 1
NYCT approved
Cast Steel per ASTM A27 Grade 60-30
Hot Dipped Galvanized
58 Grade 5, Electro Galvanized Bolt, Nut, and Lock
washer included
Twinco PN

Style

Column Flange Width

Bolt Length

069-1103-1-0

1

5

5-12

069-1103-2-0

1

5-12

6

069-1103-3-0

1

6

6-12

069-1103-4-0

1

7

7-12

069-1103-5-0

1

8-12

9

069-1103-6-0

1

10-12

11

069-1103-7-0

1

12-12

13

069-1104-1-0

2

5

5-12

069-1104-2-0

2

5-12

6

069-1104-3-0

2

6

6-12

069-1104-4-0

2

7

7-12

069-1104-5-0

2

8-12

9

069-1104-6-0

2

10-12

11

069-1104-7-0

2

12-12

13

069-1105-1-0

3

5

5-12

069-1105-2-0

3

5-12

6

069-1105-3-0

3

6

6-12

069-1105-4-0

3

7

7-12

069-1105-5-0

3

8-12

9

069-1105-6-0

3

10-12

11

069-1105-7-0

3

12-12

13

069-2119-1-0

4

5

5-12

069-2119-2-0

4

5-12

6

069-2119-3-0

4

6

6-12

069-2119-4-0

4

7

7-12

069-2119-5-0

4

8-12

9

069-2119-6-0

4

10-12

11

069-2119-7-0

4

12-12

13
View Complete Details

Rail Signal Bond PDF

A reliable signal wire-to-rail connection (RWI) is essential for signal system functionality. RWI failures cause service disruptions and can also affect the integrity of the rail, leading to rail failure. We at Twinco have developed your solution, the new Mechanical Rail Signal Bond.
View Complete Details

Trainstop Motor Housing PDF

Unit Design Information

Maximum drive down current at 110 VAC is 1.5 Amps
Maximum holding current at 110 VAC is 0.75 Amps
Final Output RPM 16
Renewable motor cable
O-rings used for water tight seal
Unit is sealed, no user serviceable parts inside
Unit weight 66 lbs.
Motor Design Information

18 Hp, 90-110 VAC 60 Hz
Driving Current < 1.5 Amps
Holding Current < .75 Amps
Completely Encapsulated Stator Winding
High Temperature winding insulation
3000 VAC insulation withstand test to ground for one minute
Gear Section Design Information

Case Hardened Gears
Overrunning clutch permanently lubricated
NSK brand, premium grade, double shielded ball bearings throughout
Hardened steel output shaft
View Complete Details

Split Sleeve Wire Marker

Along with the product features of our other tags, the Twinco Split Sleeve Wire Marker has a "lap type" joint. This allows for application of the marker either before or after the termination of the wire. It also provides for minor diameter changes so the marker will grip tightly around the wire. If required the split sleeve marker may be welded into a solid sleeve simply by applying our special cement* onto the split.
Twinco Split Sleeve Wire Markers are available in diameters ranging from 18" through 3" and lengths from 12" through 8".
View Complete Details

Twinco Impedance Bond

The Twinco Impedance Bond is a rugged, high quality, self-contained product, designed for electrified territories that utilize standard insulated joint isolation of signaling currents. It meets all applicable AAR specifications. Hundreds of Style ST-1 2500 AMP units have been in service with the Long Island Railroad (LIRR) since 1992. All components are contained in a low profile heavy duty cast iron housing, designed for mounting between the rails and across two adjacent ties. A heavy duty ramped, and diamond patterned slip resistant, removable cover is provided for ease of installation, inspection, and weather resistance. The bonds are filled with oil or petrolatum to provide moisture and corrosion protection and to aid in cooling of the bond. All hardware is either stainless steel or zinc plated for corrosion resistance.

Twinco offers a variety of impedance bonds to suit numerous applications. In addition, customized models can be developed for special situations. For over 35 years Twinco has been manufacturing solutions for the needs of many rail transit customers. Please contact your nearest Twinco sales representative, or the factory directly, to discuss your requirements.
View Complete Details

Twinco Pipe Markers

  • Length 8
Twinco Pipe Markers share all the products features of Twinco Split Sleeve Wire Markers. The only difference being that they are on a larger scale.

Twinco Pipe Markers are available in diameters ranging from 1" through 3" and lengths 1" through 8". Below are some of the more common sizes.
Twinco PN Length Diameter
51-005-16-J

51-005-24-J

51-005-32-J

51-005-48-J



8

8

8

8



1

1 12

2

3
View Complete Details

Automatic Trainstops PDF

The Train Stop is used in conjunction with wayside signals in rapid transit systems to ensure observance of, and compliance with, restrictive indications. Failure to comply with the rules reqarding such indications results in activation of the train's braking system. Operation is completely automatic, entirely independent of any action on the part of the motorman.

The system functions by mechanical contact between a wayside trip arm and a trip cock lever on the underside of the train. The wayside trip arm is lowered when the signal is clear and is raised when the signal is at "stop" or "danger". In the raised position, the trip arm will engage the trip cock lever of any train attempting to pass the signal, thus bringing it to a stop.

The Train Stop mechanism, housed in a cast-iron case, consists of a combined motor and gear housing, circuit controller with driving arm, compression return spring and sector gear. The general arrangement of these components is shown to the left. The machine by itself measures 9-78" high by 21-1316" wide by 26-38" long and weighs approximately 250 pounds.

Shown in Figure 2 below is a plan view of the Train Stop installed in a typical layout. It is mounted on two ties and includes the mechanism case. The trip arm assembly is mounted on the rocker shaft. One end of the rocker shaft is attached to the output shaft of the Train Stop mechanism. The other end is supported by an adjustable bearing strap. A trip hook assembly is mounted on top of the bearing strap and is used to hook or hold down the trip arm when required.

Figure 3 on the following page shows a side view of the trip arm in the tripping position. The trip arm is driven under electric power to the clear position, inch below the top of the running rail. It is returned to the tripping position, 2-12 inches minimum and 2-34 inches maximum, above the top of the rail by a compression return spring. When electric power is interrupted, the trip arm automatically assumes the tripping position, giving fail-safe operation.

The Train Stop is in the tripping (trip arm up) position, as shown in figure 3, when the unit is de-energized. This position, when the trip arm is up is also referred to as the stop or danger position. The trip arm is driven to a clear position when energized. The clear position is a " below the top of the running rail to the top of the trip arm head. The unit is energized when the wayside signaling system provides 110 VAC at 60 Hz. When de-energized, the trip arm is returned to the stop position above the running rail, by the compression return spring. The Train Stop mechanism will cause the trip arm to automatically assume the stop position if the power is interrupted.

Movement of the units output shaft is caused by the operation of an induction type motor and gear housing, acting on a sector gear attached to the output shaft. This counter-clockwise rotation of the sector gear also causes compression of the return spring. The output from the special 18 Hp single phase motor is changed through a series of three gears arranged in a cast iron gear box. A ratchet feature is incorporated in this gear arrangement, to protect the drive train when the rotation of the motor and gear housing is reversed by the main units compression spring.
View Complete Details

Nylon String

Twinco offers nylon string for attaching tags. There are two types; wax coated and non-wax coated

Type
Twinco PN
Wax:
PN 51-000-1-A
Non-Wax:
PN 51-000-1-B
View Complete Details

Metal Flat Tags

  • Hole Diameter 3/16
Twinco Stainless Steel Flat Tags are made from 0.036" thick stainless steel and have a 316" diameter hole for attachments. The letters are engraved into the tag.

Twinco Brass Flat Tags are made from 0.040" thick brass and have a 316" diameter hole for attachments. The letters are engraved into the tag.
View Complete Details

Twinco DA Style Disc Tags

  • Color (w/ black letters): Yellow, White, Orange, Red, Green, Blue, Beige, Gold, Silver, Gray, Violet, Brown
All 34" Disc Tags are 0.020" thickness, All remaining disc tags are 0.040" thickness

Colors Available (w black letters): Yellow, White, Orange, Red, Green, Blue, Beige, Gold, Silver, Gray, Violet, Brown, .for any color not list please call us.

Twinco PN

Disc Diameter

Hole Diameter

51-003-3-B

51-003-3-C

51-003-3-D

51-003-4-B

51-003-4-C

51-003-4-D

51-003-6-B

51-003-6-C

51-003-6-D

51-003-8-B

51-003-8-C

51-003-8-D

51-003-8-E

51-003-8-F

34

34

34

1

1

1

1 12

1 12

1 12

2

2

2

2

2

18

316

14

18

316

14

18

316

14

18

316

14

516

38
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • (Twinco Mfg. Co. Inc.)
  • Hauppauge, NY 11788 map, United States
  • Share us via

( ! ) Warning: Cannot modify header information - headers already sent by (output started at /htmlcachedir2/dynamic-html-pages/eitempfilen/usa/company/twinco-mfg-co-inc/other-products.htm:44) in /home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php on line 59
Call Stack
#TimeMemoryFunctionLocation
10.0005457656{main}( ).../index.php:0
20.01442024208include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/country-vanity/country_index_page_common_script.php' ).../index.php:309
30.13462746184include_once( '/home/sgupta/exportersindia.com/htdocs/script-files/company-page/index.php' ).../country_index_page_common_script.php:282
40.14153681880header ( ).../index.php:59
ExportersIndia: 404 Error Found
404Oops! It seems this page is not available

We connect Buyers and Sellers

Tell us What you Need

Trending Categories

Find Suppliers by Region


View All Categories

Find Suppliers by Country

Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice