Ventilation Direct

CANOPY The canopy style wall ventilator with front supply plenum provides maximum efficiency through low exhaust rates and the most effective make up air delivery in the industry. The automated production process ensures fast and consistent construction. Standard Built in rear 3" stand-off Stainless Steel Construction Stainless Steel or Aluminum baffle filters Double Wall, Insulated Front Grease Drain System Pre-punched Hanging Angles Factory Pre-wired Lighting Exceptional Lead Times PLENUM The front make up air plenum ensures proper capture and containment of cooking vapors, while preventing excessive amounts of HVAC air from being exhausted. Low Discharge Velocities Directs Air into Hood's Capture Area Even Distribution of Air Across Length of Canopy Hood Stainless Steel Construction to Match Canopy Hood

CANOPY The compact backshelf hoods are affordable solutions for mobile kitchens, concession trailers and other small spaces. Stainless steel baffle filters for improved grease removal efficiency Sloped grease drain system with removable 12 pint cup for easy cleaning Low exhaust CFM required Sturdy stainless steel construction Space saving, compact design uses limited kitchen space Hood may underhang equipment by maximum 4.5". Side Clearance is 2"

CANOPY The heat and condensate exhaust hood provides relief over non-grease appliances. Low initial and installation costs Easy access fully welded 10 gauge hanging angles Extremely low exhaust CFM requirement Available in wall type or one-piece island Available with PSP (perforated supply plenum) when make-up air is a must Hoods with perimeter gutters have a 1" drain for maximum drainage Single wall or double wall construction Hoods are available with full perimeter gutters which have welded corners

System Overview The Self Cleaning system cleans grease from the plenum and portion of the duct with the daily hot water spray cycle. Surfactant is used as part of the spray cycle to increase the cleaning effectiveness. The Self Cleaning Hood is fabricated from stainless steel and contains a spray bar that extends the full length of the hood immediately behind the filters. The spray bar is fitted with nozzles to ensure adequate spray down of the plenum and back of the filters. A nozzle is located in the exhaust riser to clean a portion of the ductwork as well. Standard Features & Benefits Fully automatic operation Hood fabricated from 100% Stainless Steel Drip-less nozzles with internal strainer Easily serviceable Adjustable wash length (factory set at 3 minutes) 34" NPT Pipe Water Inlet connection 1 12" NPT Pipe Water Drain connection Standard riser spray nozzle for duct cleaning Water usage is 0.70 GPM per foot of hood Upgrade to the CORE Fire System available High Efficiency Grease Filtration Upgrade to the CORE Fire System available Integral Utility Cabinet Integral Utility Cabinet option includes the manifold and electrical controls directly mounted into the cabinet on either end of the hood. All piping and wiring are done in the factory to minimize labor at the job site. The manifold size available is 34" and covers up to 48 feet of hood, depending on operational water pressure. Remote Manifold & Controls Remote Manifold and Controls are available when the design of the application does not allow for a utility cabinet on the end of the hood. The manifold and controls can be ordered in a remote cabinet and piped to the hood at the jobsite. The panel includes a combination pressuretemperature gauge, shock absorber, pressure reducing valve, water solenoid valve, surfactant pump, line strainer, ball valve and surfactant tank. Control Panel Options Two options for the remote manifold are available. The AM-2 Panel offers simple controls of the self cleaning operation while the SCS Panel includes advanced controls via a touch screen interface.

CANOPY The sloped front canopy ventilator offers the same proven technology of our standard canopy hood with an efficient and aesthetic solution for kitchens with low ceilings. Built in rear 3" stand-off Stainless Steel Construction Stainless Steel or Aluminum baffle filters Front Exposed Corners Ground and Polished to Match Grain of Ventilator Double Wall, Insulated Front Grease Drain System Pre-punched Hanging Angles Factory Pre-wired Lighting Face Mounted Controls Optional Exceptional Lead Times PLENUM The front make-up air plenum ensures proper capture and containment of cooking vapors, while preventing excessive amounts of HVAC air from being exhausted. Low Discharge Velocities Directs Air into Hood's Capture Area Even Distribution of Air Across Length of Canopy Hood Stainless Steel Construction to Match Canopy Hood

CANOPY The island style ventilator meets the challenges of any open floor plan cooking application. The one-piece hood with double wall insulated front and rear, along with insulated end standoffs provides clearance to combustibles and increased rigidity. 1" insulated end stand-offs for clearance to combustible Stainless Steel Construction Stainless Steel filters Design Directs Air into Filters Exposed Corners Ground and Polished to Match Grain of Ventilator Grease Drain System Pre-punched Hanging Angles Factory Pre-wired Lighting Face Mounted Controls Optional Exceptional Lead Times PLENUM The front and rear make-up air plenum ensures proper capture and containment of cooking vapors, while preventing excessive amounts of HVAC air from being exhausted. Low Discharge Velocities Directs Air into Hood's Capture Area Even Distribution of Air Across Length of Canopy Hood Stainless Steel Construction to Match Canopy Hood OPTIONAL Stainless steel wrapper which encloses area between top of hood and ceiling. Utility cabinet can house electrical package and fire suppression.