Laboratory Equipments #1604170

We are offering fuel test stand. Gpmpsi: 50 gpm, 1000 psi fluid: see below manufacturer: american lab & systems (als) hp: shown as: new nsn: product type: test stand type: part no: model no: tsfpv-50-1.5k41550 fluid: 7024 stoddard solvent calibration fluid, fuel calibration fluid descriptionfunction of unit the following test bench is designed to supply fuel flows under pressure for performance and functional testing these tests include leakage test, fuel controls test, cylinders test, actuators test, valves test, and various accessories. The test bench consists of a 10ft ha10 series console 6ft h x 4ft d and includes all fluid pumps, pump motors, stainless steel reservoir, pressure and flow controls, fluid coolers, and instrumentation. Facility power - the test bench electric power is rated for 415vac, 3ph, 50hz, 240vac, 3ph, 50hz service customer to advise which power he uses so the bench can be wired for the facility power at the factory prior to shipment. Note 220vac and 440 vac, 60hz on request. Pump test console - the pump test console will sit beside the main console. The two (2) consoles will connect via hose and cable all controls will be at the main console. The console includes a small sink 2 x 2 x 2 the console is 3ft w x 5ft h x 6ft d. The pump drive test station with vfd electronic control are inside the console. Instrumentation - all instrumentation is mounted in the vertical instrumentation panel of the main console. (ref. Para 2.0) mechanicalelectrical - mechanicalelectrical connections made between the 2 units will include a harness (1) end shall be aircraft type disconnects. The other end will be fixed in place. All wires and connections will be identified. All controls will be explosion proof. Variable frequency drive (vfd) - the vfd is rated 50hp with a speed range of 0-5000 rpm, a c-face style motor is used with adapter flanges. Customer will be required to supply test unit adapters. Gauges - a series of gauges are mounted on the panel. Each can be connected as required to indicate test pressure. Pressure gauge - test bench includes various pressure gauges. All gauges are 0.1% accurate. Auxiliary gauges-4 dia.0-100 psig, 4 dia. 0-300 psig, 4 dia.0-500 psig, 4 dia.0-1000 psig, 0-50 psig, 4 dia.0-30 hga, 6 dia. 0-200 psid flow meter accuracy- all flow meters are 0.1% accurate. Rpm & temperature- are displayed on panel mounted digital display electronic meter. Flowmeter range - the flow range is based on 7240 stoddarel solvent and is read from 50065000. Pph flow rate for test indication. A scavnge flow meter rated 0-300phh with separate ports is included in the panel. Load circuit - a load circuit is used to back pressure pumps to simulate running conditions under test. Low pressure pump - a centrifugal pump is used to provide inlet pressure to pump under test as required. In addition this pump can be used in high flow low pressure testing. Pilot pressure - a 0-1000 psi, 0-20 gpm pump motor is used to provide pilot pressure to components in test as required. This pump motor uses a vfd control to vary the speed therefore by adjusting the flow output as required too test each component. The flow range is 0-20 gpm. Valves - valves and accessories may also be tested as shown in para 8.0. This system allows for: adjustable pressure, adjustable flow, temperature control, supply and back pressure filtration systems - the system filtration is rated at 10 micron supply and return. Controls - all controls are conveniently panel mounted at the operator station calibration - all pressure gauges and flow meters will be calibrated with certification the finished unit will be built using a combination of factory new and factory overhaul components with 18 months warranty manual availablecondition: combo newoverhauledprice code: yhahar

Available in different models, our Starter Generator Test Stand is appreciated for its excellent functionality and sturdy construction. The company is the reliable Manufacturer, Exporter and Supplier of Starter Generator Test Stand located in California (United States). Our Starter Generator Test Stand conforms to all industry laid standards and thus free from defects. Moreover, our Starter Generator Test Stand is reasonable priced.

Our Heavy Test Stand is widely in demand around the world owing to its sturdy construction and outstanding performance. We make use of only top-grade raw material for the fabrication of our Heavy Test Stand. Moreover, buyers can get it customized from us according to their own required specifications. We are capable of undertaking bulk orders of Heavy Test Stand at market leading prices.