BLACOH Fluid Controls, Inc.

United States

remove hydraulic shock and vibration, enhancing all-around performance and reliability of fluid flow applications.Positive Displacement (PD) pumps create pulsation and hydraulic shock due to the reciprocating nature of their stroking action, potentially damaging the entire pumping system.BLACOH's SENTRY Pulsation Dampeners & Surge Suppressors remove virtually all hydraulic shock, enhancing all-around performance and reliability of fluid flow in industrial and chemical transfer applications.

Calibration Columns are installed on the suction side of the metering pump and are isolated with two valves installed with the cylinder. The top of the cylinder is vented back to the supply tank or drain. The calibration cylinder is filled to the top mark then the valve from the tank is closed. Turning on the metering pump will draw down the liquid providing a simple means to verify the accuracy of the pump flow rate. USGPH (Gallons Per Hour) and ML are shown on the cylinder. Blacoh SENTINEL Calibration Columns are critical to accurate determination of your system flow rate, either at start-up or following maintenance. They are offered in clear PVC or Borosilicate glass. Max cylinder pressure is 15psi.

Diaphragm pressure relief valves are designed to protect pumping systems from over pressure damage caused by defective equipment or blockage in the pump system line. Robust construction ensures reliability in the rigorous service of municipal and industrial applications.Diaphragm pressure relief valves operate when the pressure in the pumping system exceeds the preset pressure of the valve. The diaphragm is held against the valve seat by an internal spring. When the preset pressure is exceeded the diaphragm is forced up and the system fluid flows out the relief port, back to the system fluid tank or to the suction side of the pump. The valves are pre-set at 50 psi, however they are field adjustable from 10 to 150 psi, (optional 350 psi) via the adjustment screw. The relief valve should be set approximately 15 psi higher than the system pressure. Installation should be made as close to the pump as possible, without any valves or accessories between the relief valve and the pump. Consult your pump manufacturer for recommendations.

Without proper protection, process fluids regularly contaminate and damage in-line system instrumentation. The strength and durability of SENTINEL diaphragm seals isolate and protect all forms of system instrumentation from the hazards of corrosive process fluids.Diaphragm Seals, also referred to as gauge guards', employ a chemically resistant diaphragm to effectively isolate process fluids from gauges and other system instrumentation. The durable diaphragm allows SENTINEL to accurately transfer process fluid without direct contact with hazardous or corrosive process fluids. Our SENTINEL Diaphragm Seals are easily installed, come in a variety of chemically resistant materials, and work in both pressure and vacuum conditions.

sanitary flow through dampener with unique bladders is specifically designed for hygienic clean-in-place applications.The clean alternative for pulsation dampening.Specifically designed for hygienic applications requiring clean-in-place components, the SENTRY CIP pulsation dampener with inline flow through design and unique patent pending tube bladder eliminates problems with product holdup and trapped particles. Ideally suited for handling slurries and viscous fluids, its gentle enough for the most delicate products.

By preventing reverse flow, check valves can be used as one-way valves, injection valves, or to prevent backflow. Check valves allow flow in one direction, automatically prevent back flow when process fluid in the line reverses direction, and will work even if the system loses air or electricity. Installed in the process pipe, check valves are flow sensitive and rely on the line fluid to open and close. The internal ball or poppet functions as a positive shutoff to ensure process fluid does not go back up the line. Check valves can be installed vertically or horizontally. Robust construction ensures reliability in the rigorous service of municipal and industrial applications.

The fully pneumatic SPILLSTOP system safely captures leaked product and automatically shuts down failed pumps to eliminate costly product loss and prevent hazardous spills. Optional warning alarm and backup pump switchover further minimize system downtime for maximum productivity. Stop the spill before it happens.

Diaphragm seals, also referred to as gauge guards, isolate all forms of system instrumentation from hazardous and corrosive process fluids unconditionally guaranteed!

Back pressure valves enhance the performance of pumping systems by applying a continuous back pressure to the system pump, while also acting as an anti-syphon valve.

Inject Quills for safe delivery of chemicals into pipelines Blacoh SENTINEL Injection Quills are used to provide safe delivery of chemicals into pipelines. The quill end ensures the dispersion of the chemicals away from the pipe wall. The integral spring loaded check valve prevents backflow from the pressurized pipe if there is a break in the discharge piping. A union connection on the inlet allows for ease of installation and maintenance.

remove hydraulic shock and vibration, enhancing all-around performance and reliability of fluid flow applications.Positive Displacement (PD) pumps create pulsation and hydraulic shock due to the reciprocating nature of their stroking action, potentially damaging the entire pumping system.BLACOH's SENTRY Pulsation Dampeners & Surge Suppressors remove virtually all hydraulic shock, enhancing all-around performance and reliability of fluid flow in industrial and chemical transfer applications.