Our Product / Services
Our product range comtains a wide range of mounted ball bearings, belt drives, Torque Overload Devices, gearing and v-belt sheaves
Synchronous Belt Drives help reduce the problems of slippage, belt stretch, lubrication, and metal-to-metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives. In addition to an extensive belt drive line, Browning® now offers two synchronous belt drive offerings. These lines serve applications up to 600 HP. They include the HPT® High Performance Timing drive line and many additional sizes of the proven Browning® Gearbelt® Drive line. Added selections include double Gearbelt belts which furnish a variety of design solutions for changing shaft rotations.
Improved airflow Focused cooling and heating air distribution Curtain guards can help reduce PTAC run time by supplying air to the room and not behind a curtainSupplying air to the room and not behind a curtain can reduce onoff time Reducing onoff time can help reduce component wear and unit maintenance
A variety of wired thermostats may be used with the Amana brand PTAC. All thermostats offered can be connected to the PTAC through a low-voltage connection. The Amana brand DigiSmart™ PTAC also offers a wireless remote thermostat. Any thermostats other than those listed below or the DigiSmart thermostat must be submitted to Goodman for approval prior to use. For more information, please call: 1-800-647-2982
Our insulated, stone-wood beige metal sleeves with industry standard dimensions are shipped with a weather board for use during construction.42" (W) x 16 116" (H) x 14⅛" (D) The WS900E is an industry-standard depth of 14⅛". The extra-deep sleeves can be custom ordered starting at 16" to 24" in 1" increments as well as from 28" to 36". Sleeves may be shipped separately to allow for installation during construction.
Available in stamped-aluminum, extruded aluminum, or in a one-piece molded version for use with any of our WS900D wall sleeve.AGK Extruded aluminum architectural grille available with anodized aluminum finish and a baked-on paint finish for durability. Choose from 3 stock colors or a custom color: PGK One-piece injection molded grille using a polymer blend of engineered thermoplastic high-impact strength material with chemical resistance and an exterior UV protective coating. Choose from 3 stock colors:
The condensate drain attaches to the wall sleeve base pan or the wall sleeve's outside corners for controlled indooroutdoor disposal of condensate. Install the wall sleeve in the wall before an indooroutdoor drain kit is installed.
Main Duct and TransitionWhen two adjacent rooms need to be conditioned, these kits deliver air to both rooms (airflow distribution can be adjusted from 6535 to 8020). Refer to EDK02B (Extension Duct Kit) and TDK02B (Duct Extension Kit- Terminal Duct & Grille) for complete installation.
Includes a grille and sleeve for fitting a duct extension through the wall.Includes a grille and sleeve for fitting a duct extension through the wall. Refer to MDK02B (Duct Extension - Main) for complete installation.
For use on non-baffled grilles.Includes 2 air-deflection baffles that can be mounted on the condenser coil to direct air toward the center and away from the inlet. This prevents the re-circulation of hot condenser air, maintaining unit cooling and heating capacity and unit efficiency. Use the baffles when an older unit is being replaced and when the existing grille does not have deflector baffles. Any existing baffles must be removed to install this kit.
In conjunction with the tamper-resistant front, the installation of Amana® brand security key locked security controls cover, prevents tampering with the controls used to set temperature, heating and cooling functions.U.L. approved for institutional use only
Six sleeves (three rear installation, three side installation) are available for varying wall depths from 5" to 15".The sleeves can be shipped separately to allow installation during construction. Each sleeve includes a factory installed "weather guard" to cover sleeve opening during construction until VTAC is ready for installation. It is recommended that where possible wall sleeves be installed in the rear installation and not in the side installation. This gives better access to the VTAC.
Panels (31" W x 82" H or 31" W x 87" H) are available louvered or non-louvered and are insulated for sound reduction with tamper-proof screws.Louvered panel includes a 20" x 24" x 1" filter. Non-louvered panels require external return air grilles and unit mount filters. Rough-in dimensions: 82" panels — 28" wide by 79" high
Our System Plast™ mounted bearing supports are available in polyamide and Nolu-Clean materials. These Supports are also available with either a 400-series stainless steel insert or a 52100 bearing quality chrome steel insert. They are offered in a variety of housing styles and have an optional end cap and backside shield. This makes them a good solution for wash-down applications.
The Amana brand DigiSmart™ PTAC also offers a wireless remote thermostat.2-way wireless communication between PTAC and thermostat. Communication without a line of sight. Easy to install single connector for antennae communication.
Breakthrough Efficiency: 25+ SEER 13+ HSPF Enhanced Comfort: TemperatureHumidity control and hot air supply in winter conditions Proven Reliability: Protected by CoreSense™ Versatile Applications: 2-5 ton residential and light commercial applications High efficiency BPM motor