Buske L.L.C.

United States

Designed to put a twist in your pull with its V-shaped gusset. There are three positions from which to pull. For use on bolt-type hinge pillars. Overall Length: 512" (133mm)Slots:12" x 112" (12mm x 39mm)Weight: 2 lbs (.91kg)Capacity: 2 tons (1, 814kg) Heat Treated Steel. Made in the U.S.A.

includes anchor body #527 and cover #526 Buske's Concealed Floor Anchor systems can turn your stalls into full-function frame stalls and eliminate sublet work. This new dual-purpose anchor system may be used to tie down auto body and frame jobs in the conventional manner of may be used for holding beams. By using a variety of beams and accessories, a variety of hook-ups can be accomplished. Portable equipment may be anchored in any position 360 deg. around the damaged vehicle. The floor anchors are installed flush in existing concrete floors or while a new floor is being poured. Complete installation instructions are available below. By placing the covers on the anchors, the entire work surface becomes one smooth, level floor. Portable equipment and dollies glide over the covers and floor smoothly. The stall is easy to keep clean. The B532 can be used with the B525 to make pulls directly from a 2 x 4 beam. The B532 inserts into the B525, then the 2x4 beam inserts into the tube at the top of the B532 turret. Keeping the long side of the 2x4 pointed towards the object you will be pulling on you can make many repairs. B532 shown in photo set above. Made with US materials and workmanship.

The harder you pull, the firmer it wedges. Allows full 360-degrees of pull without chain touching floor. Can be removed and installed in a different location. When correctly installed, top is flush with floor when not in use. Can be easily cleaned by lifting top. 312" (89 mm) cored hole required in concrete floor. Weight: 7 lbs (3.18 kg)Capacity: 10 tons (9, 072 kg) Heat Treated Steel. Made in the U.S.A.

Great for bolting to a frame, unibody rail or to other places to make a secure pull. Each bar has a combination of hole patterns to facilitate bolting to a vehicle. May be used in conjunction with various accessory items for specialized pulling needs. Overall Length: 13" (330 mm)Width: 212" (58 mm)Weight: 4 lbs (1.81 kg)Capacity: 3 tons (2, 722 kg) Replacement Parts: #5220 Clevis Pin & Rue Clip Heat Treated Steel. Made in the U.S.A.

INCLUDES BOLT AND WASHERThe B1341 uses a 2 12" cylinder and is most comonly used with the B1325 POSI-LOCK Chainless Anchor System. Can also be used with the B1349 EZ bolt anchor pull adaptor shown above

WITHOUT BOLT AND WASHERThe B1340 uses a 2 12" cylinder and is most comonly used with the B1325 POSI-LOCK Chainless Anchor System. Can also be used with the B1349 EZ bolt anchor pull adaptor shown above

Keep your tools organized!Design your own tool board and order hooks from Mo-Clamp.Our blank boards are available in two sizes #5035 24"x24" weight 8 lbs. #5036 24"x48" weight 16 lbs. Does NOT include hooks !

Keep your tools organized and in good condition with handy tool boards. The package includes the #5051 Tool Board with Hooks, #3120 Small Round Nose Sheet Metal Hook, #3140 Large Round Nose Sheet Metal Hook, #4043 Oval Loop, #4044 38 " Screw Pin Shackle, #4052 Triangle, #4145 Double Grab Hook Assembly, #4151 Grab Hook & Single Claw w18-inches of " chain, #4152 Two Single Claws w18-inches of " chain, #4154 Hole Plug & Single Claw w18-inches of " chain, #6006 6' of " Mo-Clamp Frame Straightening Chain, #6220 " Super Alloy Clevis Grab Hook, #6250 " Super Alloy Clevis Slip Hook, #6300 Nylon Sling, and #6350 Cable Sling. #5051 Toolboard Dimensions: 2'x4' hooks are includedTotal Weight: 62 lbs (28.13 kg) Tools are Heat Treated Steel and Made in the U.S.A.

Made of tough Delrin Plastic. Designed to fit all Mo-Clamp trams including baby tram and #7000. Allows centering of holes for easier 1-man tramming on underside of vehicles and engine compartments. Will make sure you are centered on those holes for precise measurements.Weighs 2oz.size: 2" cubedMade in USA