CARTRIDGE HEATERS MAXIWATT LLC

MIAMI, United States

Compressed cartridge. Termination with racort Ref. "T8"

Totally watertight and reinforced cartridge, prepared for an easy extraction, by means of a thread, of its location in case of dislodging of the same one. Ideal for areas where there are watertight pressures and liquids. The Ref. T8 termination is indicated for heating areas where there are pressures (oil tanks, water, glues, plastics) or deflagrations.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Metric Termination Ref. "T4"

Cartridge with stainless steel metric stud, useful for quick cable replacement.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Simple-pole screw termination Ref. "T6"

Cartridge with metric screw output, single-pole with quick cable extraction.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Termination with racort Ref. "T9"

Completely watertight and reinforced strength, prepared for easy removal from its location with reinforcement that prevents deformation in case of dislodgement. The Ref. T9 termination can be applied in any hostile situation (high temperatures, material waste).

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Finished with steatite Ref. "T2"

Cardrige with a ceramic piece (steatite), which protrudes from a length of 3 to 4 millimeters, depending on the diameter, avoids the crossing of the cable with the tube and gives more consistency to the entry. the diameter of the cartridge, avoids the crossing of the cable with the tube and gives more consistency to the cable entry of cables.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Termination with plate Ref. "T7"

Fully compressed and reinforced cartridge, prepared to hold the piece to be heated robustly. Ideal for areas with movements and vibrations.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Simple-pole cable Termination Ref. "T5"

Cartridge with single-pole fiberglass cable output for low-voltage cartridges.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Termination with plate Ref. "T7B"

Fully compressed and reinforced cartridge, prepared to hold the piece to be heated, ideal for areas with movements and vibrations.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Termination with tab Ref. "T3"

Cartridge with a ceramic piece (steatite). Prepared for quick change of cables.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.

Compressed cartridge. Base termination Ref. "T1"

Fully compressed cartridge, with a refractory ceramic paste sealing the entrance. It is the base cartridge. from this cartridge the other modifications are made.

Recommendations:

Cartridges should be as tight as possible.

When preparing to drill holes where the cartridge will be located, consider the following factors:

• The inside of the bore should be uniform, without scratches or different diameters, however small, it is recommended to finish it with a reamer.
• Heat rises
• Dissipation is higher at the ends and heat will be concentrated in the center.
• Choose stock cartridges between 8 to 11 W/cm2
• Try to have the drill with an outlet, in order to have an easier disassembly.
• The connections must never be inside the borehole, as there is a risk of crossover or burning.
• The connections must be protected to prevent liquids, plastics, gases, etc. from falling out.
• It is advisable to incorporate probes that should be at a maximum distance of 15 mm from the cartridge, connected to a temperature regulator.
• The cartridges must have a minimum cartridge spacing of 3 times the cartridge diameter.

Indications:

• Indicate with symbols the warning of hot surfaces.
• Store as protected from humidity as possible.
• Cut off the total current of the machine or mold.
• Check that the machine or mold is at room temperature.
• Introduction without any anti-cold paste.
• Holes exclusively with H7 tolerance.
• Attach regulation and cut-off systems (thermocouples and regulators).
• Introduction of 100% of the cartridge case length.
• Do not insert the connection cable inside the hole.
• Protect the cables and connection inlet of the cartridge from: shocks, splashes and excess material.
• Do not pick up or carry the cartridge by the cable.
• Keep the cable away from the heat source and protected from heat.
• Do not repair damaged cables. Replace them with new ones identical to the original ones.
• Indicate and submit in writing, before acceptance of the order, the working conditions (vibration, shocks, humid environments).
• Never leave in operation without qualified human presence.
• All of the above are mandatory for the safety of people and property.