Heat Exchanger USA

United States

Heat-Exchangerusa.com fabricates Shell & Tube Heat exchangers that will meet all industry specifications. We meet all ASME and TEMA (B, C, & R) Requirements as well as all of our units comply with Sections l, lV, Vlll, Div. 1 . Just fill out the easy form below with your Name and info from your existing heat exchanger and Heat-exchangerusa.com can get all documents necessary to produce the exact same unit you have now. If you are only looking for a Replacement Tube Bundle then please follow this link www.tubebundle.com to get a quote on any size tube bundle or any material need for you specific application.

All of our designing and fabricating is done in house so you do not have to worry about the quality of the product you are receiving. We follow strict ASME Section VIII, Division 1 requirements in addition to TEMA B, C, & R standards. Heat-Exchangers USA enjoys working with our customers to help provide solutions for difficult fluid flow, heat transfer, or corrosion problems with our resourceful fabrication designs and complex material selection.These shell and tube heat exchangers are made with the chemical and petrochemical industries in mind, as well as refineries, the paper industry, utilities, and many more.Heat exchangers are used in both commercial and industrial settings as they are often relied on to remove heat and transfer heat energy in a number of different applications. The life span of a heat exchanger ranges from 10 to 20 years, assuming that they are well maintained. Because of their job and exposure to high temperatures and increased pressure, heat exchangers often experience premature failure. This is when you must make the decision to either replace your unit or make the repairs; the decision is primarily based on your budget and luckily for you, Heat-Exchanger USA offers both the repair and replacement units.EngineeringPerformance, thickness, and specification calculations, as well as drawings and manufacturing procedures, for all shell & tube heat exchangers and tube pipe coils are prepared solely by the Heat-Exchangers USA Engineering Staff.Outside consultants are utilized as specific needs demand.Heat-Exchangers USA engineering personnel are prepared to make on-site inspections for all data relevant to the products they design and manufacture.The costs of engineering are a normal overhead item included with the price. JFD will design, size, and price heat exchangers with (1) set of operatingprocess conditions, and a maximum of (1) alternate material selection set.Liquid Penetrant Testing: All other NDE by subcontractHydrostatic Testing: Water pressure up to 5000 psigPneumatic Testing: Air pressure up to 125 psigBending: ASME Jig for welder qualificationsQuality Control: Per ASME specificationsProductionHeat-Exchangers USA is equipped with a 13, 000 square foot production floor, fully furnished with a wide variety of radial drills, lathes, mills, coiling and bending machines, as well as other general machine shop equipment.(3) CNC Vertical Machining Centers: Drilling, Milling, and other machining accurate to .0001.(3) Pines Bending Machines: Bend Tube Pipe from to 6 IPS. Large diameter tube pipe forming also available.All welders and weld procedures are A.S.M.E. certified in standard and specialty alloys. Qualified procedures include: Carbon Steel, Stainless Steel, Copper, Titanium, Inconel, Hastelloy, and others as required.SubcontractorsWhen an applications specs are such that not all criteria can be met by Heat-Exchangers USA, subcontractors are used. Subcontracting services include:Heat Treating Annealing Stress RelievingSandblasting Non-Standard PaintingSpecial Machining: Local machine shop as requiredX-Ray Pipe Tube Weld inspection

Standard Armstrong Water to Water (W) complete Shell and Tube Heat Exchangers. 2 and 4 pass units, 4" nominal thru 10" nominal in our catalog. Larger units available upon request.Armstrong U-Tube heat exchangers are designed for durability and include a removable tube bundle as a standard feature. The U-shaped tube design provides a long service life by eliminating the effects of thermal expansion and contraction. These heat exchangers feature carbon steel components, with copper tubes, and a rugged cast iron head.

Boilersupplies.com can supply your company with a replacement Liquid to Liquid Shell and Tube Heat Exchanger for an Adamson model that will meet all of the industry specifications such as ASME and TEMA requirements (B, C, & R) as well as our units complying with (Sections I, IV, VIII & Div. 1).Materials:Standard Copper (tubes), carbon steel (shell, tube sheet, baffles) Optional Brass (tubes, tube sheets, baffles), bronze (heads), stainless steel (tubes, tube sheets, heads, shells, baffles), 9010 Cu-Ni (tubes)Just fill out the easy form below with your name and information from your existing heat exchanger and BoilerSupplies.com can get all of the documents necessary to produce the exact same unit that you have now. Other manufacturers we carry are Bell & Gossett, Armstrong, Alco, American Standard, A.O. Smith, Cemline, Graham, Old Dominion, Standard Exchange, Taco, Patterson Kelley, Reco, Thrush & Heat Exchanger USA.

All of our designing and fabricating is done in house so you do not have to worry about the quality of the product you are receiving. We follow strict ASME Section VIII, Division 1 requirements in addition to TEMA B, C, & R standards. Heat-Exchangers USA enjoys working with our customers to help provide solutions for difficult fluid flow, heat transfer, or corrosion problems with our resourceful fabrication designs and complex material selection.These shell and tube heat exchangers are made with the chemical and petrochemical industries in mind, as well as refineries, the paper industry, utilities, and many more.Heat exchangers are used in both commercial and industrial settings as they are often relied on to remove heat and transfer heat energy in a number of different applications. The life span of a heat exchanger ranges from 10 to 20 years, assuming that they are well maintained. Because of their job and exposure to high temperatures and increased pressure, heat exchangers often experience premature failure. This is when you must make the decision to either replace your unit or make the repairs; the decision is primarily based on your budget and luckily for you, Heat-Exchanger USA offers both the repair and replacement units.EngineeringPerformance, thickness, and specification calculations, as well as drawings and manufacturing procedures, for all shell & tube heat exchangers and tube pipe coils are prepared solely by the Heat-Exchangers USA Engineering Staff.Outside consultants are utilized as specific needs demand.Heat-Exchangers USA engineering personnel are prepared to make on-site inspections for all data relevant to the products they design and manufacture.The costs of engineering are a normal overhead item included with the price. JFD will design, size, and price heat exchangers with (1) set of operatingprocess conditions, and a maximum of (1) alternate material selection set.Liquid Penetrant Testing: All other NDE by subcontractHydrostatic Testing: Water pressure up to 5000 psigPneumatic Testing: Air pressure up to 125 psigBending: ASME Jig for welder qualificationsQuality Control: Per ASME specificationsProductionHeat-Exchangers USA is equipped with a 13, 000 square foot production floor, fully furnished with a wide variety of radial drills, lathes, mills, coiling and bending machines, as well as other general machine shop equipment.(3) CNC Vertical Machining Centers: Drilling, Milling, and other machining accurate to .0001.(3) Pines Bending Machines: Bend Tube Pipe from to 6 IPS. Large diameter tube pipe forming also available.All welders and weld procedures are A.S.M.E. certified in standard and specialty alloys. Qualified procedures include: Carbon Steel, Stainless Steel, Copper, Titanium, Inconel, Hastelloy, and others as required.SubcontractorsWhen an applications specs are such that not all criteria can be met by Heat-Exchangers USA, subcontractors are used. Subcontracting services include:Heat Treating Annealing Stress RelievingSandblasting Non-Standard PaintingSpecial Machining: Local machine shop as requiredX-Ray Pipe Tube Weld inspection

Heat-Exchangerusa.com fabricates Shell & Tube Heat exchangers that will meet all industry specifications. We meet all ASME and TEMA (B, C, & R) Requirements as well as all of our units comply with Sections l, lV, Vlll, Div. 1 . Just fill out the easy form below with your Name and info from your existing heat exchanger and Heat-exchangerusa.com can get all documents necessary to produce the exact same unit you have now. If you are only looking for a Replacement Tube Bundle then please follow this link www.tubebundle.com to get a quote on any size tube bundle or any material need for you specific application.