Our Products #4785222

120 Truss-Mesh is a truss type continuous length joint reinforcement for single wythe walls.Hohmann & Barnard's Lox All Truss-Mesh and Lox All Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry wallsJoint reinforcement has long proven to be necessary for superior performance of masonry wall construction, as it offers the following benefits:Reinforces a variety of masonry wallsGreatly reduces cracking that can arise from thermal stressesEnhances resistance to water penetration, as cracks are controlledIncreases lateral flexural strengthBonds exterior and interior masonry wythes together in composite wallsBonds masonry at intersecting walls and cornersIncreases elasticityIncreases performance of masonry walls under various stressesFabricated in conformance with ASCEACI 530 building code requirements for masonry structures, and ASTM A 951 (standard specification for masonry joint reinforcement)

130 Truss-Tri-Mesh has three longitudinal (side) rods to reinforce block and brick composite wallsHohmann & Barnard's Lox All Truss-Mesh and Lox All Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry wallsJoint reinforcement has long proven to be necessary for superior performance of masonry wall constructionFabricated in conformance with ASCEACI 530 building code requirements for masonry structures, and ASTM A 951 (standard specification for masonry joint reinforcement)

140 Truss Twin-Mesh has 4 Longitudinal (Side) Rods to reinforce block-and-brick or block-and-block composite walls (block-and-block product and application shown in renderings)Hohmann & Barnard's Lox All Truss-Mesh and Lox All Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry wallsJoint reinforcement has long proven to be necessary for superior performance of masonry wall constructionFabricated in conformance with ASCEACI 530 building code requirements for masonry structures, and ASTM A 951 (standard specification for masonry joint reinforcement)

150 Truss Box-Mesh for block-and-brick composite walls. Welded boxes project from backup Truss Reinforcement and tie into brick faceHohmann & Barnard's Lox-All Truss-Mesh and Lox-All Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry wallsLox All Truss 150 is a single-unit veneer systemFabricated in conformance with ASCEACI 530 building code requirements for masonry structures and ASTM A 951 (standard specification for masonry joint reinforcement)

H&B C-Coat Flashing is a copper thru-wall flashing with the following advantages:The flexibility and toughness of copper are combined with the superior waterproofing of elastic, asphalt compound coatingThe sheet copper is shielded from acids, alkalis and electrolysis that may be present in uncured mortarThe asphalt coating is self-sealing in case of puncture

165 Lox-All Truss Style Adjustable Joint Reinforcement has "winged loops" welded to the back-up reinforcing. The loops accept the compressed leg 2X-HOOK to allow vertical adjustability while restraining transverse movement of the two wythes.Suitable for: Collar joint conditions, Cavity walls, and Insulated wallsFabricated in conformance with ASCEACI 530 building code requirements for masonry structures and ASTM A 951

Ties the masonry veneer to the substrate. The The Concrete Seal Tie's screw portion has special alternating threads making it suitable for use with concrete, CMU, wood stud or brick backup, and is provided with EPDM sealing washers.Consists of a Concrete Seal Tie combined with the 2-Seal Byna-Lok Wire TieThe special point affords easy installation into a predrilled hole.Barrel portion available in 58", 1", 1-12", 2", 2-12", 3", 3-12", 4", 4-12", and 5" lengths to accommodate thickness of insulation andor wallboard.

220 Ladder Mesh Reinforcement's cross rods are spaced so block cells are not obstructed, allowing easy placement of vertical rebarsA full 8" splice between lengths of ladder is facilitatedHohmann & Barnard's Lox All Truss-Mesh and Lox All Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry wallsJoint reinforcement has long proven to be necessary for superior performance of masonry wall constructionBenefits:Greatly reduces cracking that can arise from thermal stresses. This enhances resistance to water penetration, as cracks are controlled.Increases lateral flexural strength.Bonds exterior and interior masonry wythes together in composite or cavity walls. Also bonds masonry at intersecting walls and cornersIncreases elasticity and performance of masonry walls under various stressesFeatures:Butt-welding of cross rods to longitudinal rods (not more than 16o.c.). This construction enhances bonding capabilities, eliminates projection of cross rods beyond the specified width of reinforcement, and prevents excessive build up of wire in limited mortar jointsContinuous deformation along each longitudinal rod for superior bonding performanceH&B products conform to ASTM A951 standard specification for masonry joint reinforcement

170 Lox-All Truss Style Adjustable Joint Reinforcement with Eyelets for vertical adjustability and the H&B Seismic Hook for continuous wire.H&B SH-Seismic Hook:This hook is swaged (indented) in two places to accommodate either a 9 gauge or 316 continuous wireA channel is formed that braces the continuous wire and holds it in placeSuitable for standard 38 jointsRectangular hookpintle acts as a vertically adjustable anchor to bond exterior masonry, while restraining in and out movement.Design of hookpintle serves to mechanically secure insulation to masonry backup.Specify SH Seismic Hook with any adjustable wire, such as #170-SHU.S. Pat. No. 6, 789, 365 & 7, 325, 366 - Other Patents PendingProjecting eyes are 4 point welded to the backup truss reinforcement.Allows construction of interior wythe in advance of exterior wythe.Fabricated in conformance with ASCEACI 530 building code requirements for masonry structures and ASTM A 951 (standard specification for masonry joint reinforcing).

The Thermal Concrete 2-Seal Wing Nut is an innovative single screw veneer tie for concrete, CMU, or wood stud construction. The anchor features a dual-diameter barrel with factory-installed EPDM washers to seal both the face of the insulation and the airvapor barrier, and unique Thermal Wings that are designed to decrease thermal transfer through rigid insulation.The projecting Thermal Wings:Are made from steel encapsulated in plastic to create a thermal break, the plastic is highly flame resistantAccept a 2X-HOOK or Seismic 2X-HOOK and spin to easily orient pintleshooks parallel to masonry jointsUp to 12 of inward adjustability to account for variations in wall thickness