MAXPRO Technologies, Inc.

United States

For high pressure applications or where air drive pressure is low MAXPRO offers three double acting - single stage boosters with a double air head.These models include the DLE15-2, DLE30-2 and DLE75-2.

Exceeds industry standard of 60, 000 psiMAXPRO offers a complete line of MAXIMATOR high pressure fittings, tubing, check valves, line filters, anti-vibration fittings and safety head assemblies, as well as elbows.

Exceeds industry standard of 15, 000 psi. Pipe fittings are designed for liquid and gas applications. The P Series Fittings are available from 14" to 1" NPT to 15, 200 psi. NPT threads must be sealed using a high quality PTFE tape andor paste product. Sealing performance may vary based on many factors such as pressure, temperature, media, thread quality, thread material, proper thread engagement and proper use of thread sealant. Recommends to limit the number of times an NPT fitting is assembled and disassembled because thread deformation during assembly will result in deteriorating seal quality over time. When using only PTFE tape, using thread lubricaion to prevent galling of mating parts is recommended.

Exceeds industry standard of 60, 000 psi. MAXPRO offers a line of cold drawn thick wall tubing, with flow areas to compliment the high pressure valves and fittings. This tubing is made under strict manufacturing and quality control standards and inspections, with dimensional tolerances to match the requirements of the high pressure coned and threaded connections. The standard materials are 304 and 316 stainless steels. Other materials may be provided on special request, depending on the specific material, diameters and lengths.

MAXIMATOR Pipe Hex Nipples are designed for rapid system make-up. They are available in various lengths for pipe valves and fittings. In addition to the minimum lengths (Pipe Hex Close Nipples) and standard lengths listed in the table below, Pipe Hex Nipples are also available in custom lengths. Please consult factory.

MAXIMATOR Pipe line filters are used to filter process fluids in high pressure systems. The cup type design is used when maximum filtration surface area and a single micron size element is preferred. This design increases the filter area as much as 6 times the area of the disc type filter, and will permit higher flow rates with a lower pressure drop, and longer intervals between element changes. Filter elements come standard in: 5, 30 or 56 micron sizes and are easily replaced. Filters are rated for temperatures -60F to 660F.

MAXPRO offers five gas boosters in the single acting - single stage configurationSingle stage - single acting boosters are the smallest and lightest of the Maximator family, yet capable of output pressures up to 10, 000 psi.

MAXIMATOR air operated valve actuators are piston type design, and are mounted on a manual valve to provide remote control capability. There are two styles of air actuators available, and selection is based on the valve size, system pressure, and air pressure available.

MAXPRO Air Amplifier Systems are ideal for turn-key installation at work stations or machine centers to boost plant air pressure for tools or operation of pneumatic clamps, cylinders and other equipment. These systems provide short-term high flow air or constant flow with reserve, at a constant regulated output pressure. Storage tank is per A.S.M.E. Code and CRN (Canada) and comes with a safety relief valve, drain valve and pressure gauge.Each 200 psi and 250 psi system is also equipped with an inlet air filter and outlet pressure regulator with gauge, all mounted on a common base. The 500 psi and 600 psi systems are equipped with an inlet air filter and inlet air pressure regulator with gauge. High pressure outlet regulator with gauge is available as an option (Add "-R" for a 14" FNPT regulator or "-12 R" for a 12" FNPT high flow regulator to system catalog number). MAXPRO Air Amplifier Systems are available in a number of arrangements and custom designed units are also

14" angular seat rupture discs are designed to be used with the safety head assemblies that are shown above. Minimum rupture disc pressure ratings should be at least 110% of system operating pressure. The standard rupture disc material is Inconel. The pressure ranges indicated in the table below are at room temperature (72F). Other materials and pressure ranges are available upon request.