Milspec Earth Anchors

United States

our Anchor Set- Storage Building or All Purpose Use A must for wind protection!4 Anchor Set 12 Shaft 30 Long w4 Helix. A must for wind protection!Easy to install by hand! Removable ReuseableSet consists of:4- 30 Eye Anchors with 4 Helix Welded closed loop!Installl by hand or machine both available under Installation tools

Product Description Contractors Save BIG Limited Supply! Ideal for Contractors needing to Anchor down installed Sheds etc.! Up to 2, 300 Lb pull out resistance for each Anchor! Lighter that other style Anchors- Save on *Shipping!4 Ground Anchor Contractor Bulk Set Special- WITH DRIVE ROD!These arrowhead Ground Anchors are designed after our highly successful Mil-Spec anchors which have been proven and tested out in the field for over 40 years.

Powerful 14 AMP motor delivers 25.7 lbs. of impact energy to handle the most demanding applicationsConstant Speed Control automatically applies additional power to the motor to maintain consistent speed under load for the most challenging jobsSoft Start suppresses start-up reaction for more control and better accuracyL.E.D. Service Light notifies the user approximately 8 hours before the brushes need to be replacedL.E.D. Power Lights indicate switch failure or cord damageVariable Speed control dial enables user to match the speed to the application for greater versatilityExtended Life Brushes are longer for more work between service intervals and less downtimeAutomatic Brush Cut-Off protects commutator from damage for longer tool lifeNo hammering when idling helps increase tool lifeEasy-to-operate slide switch increases productivity and allows for continuous useSide-handle swivels 360 for greater controlRubberized ergonomic soft grip provides more comfort and controlMakita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool lifeDurable blow-molded rolling tool case for safe storage and easy transportation

orque Limiting Clutch Engineered to Reduce Gear DamagePowerful 10 AMP motor delivers 4.6 ft.lbs. of impact energy to handle the most demanding applications2-mode operation for Hammering Only or Hammering with RotationRubberized ergonomic soft grip provides more comfort and controlNo hammering when idling functions helps increase tool lifeOne-touch sliding chuck for quick bit changesTorque limiting clutch engineered to prevent gear damage by automatically disengaging gears if the bit bindsSequential impact timing delivers timed hammering during rotation to minimize overlapping bit impacts for up to 50% faster drilling12 bit angle settings allow the bit to be set at different positions for operating convenienceAutomatic brush cut-off protects commutator from damage for longer tool life12 bit angle settings allow the bit to be set at different positions for operating convenienceMakita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life

Package of 10 Cable Clips for 18 Wire RopeAllows for on site termination of cableSize: For 18 CableMaterial: Malleable IronCoating: GalvanizedWrench Size: 316Apply Correctly U bolt should be on end of Rope- Re- tighten after initial load

Helical Piers come in different designs- Generally speaking: Round Shaft Helical Piers are used for Compression applications such as foundation repairs and supports for both Residential and Commercial applications in addition to new construction such as Walkways, Building supports, Light poles, Board Walks, Utility equipment etc.While Square Shaft Helical Piers are used for Tension Applications such as Tie Backs, Anchoring Applications, Guying Towers, Tilt Up construction etc.

Makita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life.SKU: msa-hr4041c Category: MakitaapplicationsConstant speed control automatically applies additional power to the motor to maintain speed under load to complete the most challenging jobsSoft start suppresses start-up reaction for more control and better accuracyVariable speed control dial enables user to match the speed to the application for greater versatilityTorque limiting clutch engineered to prevent gear damage by automatically disengaging gears if the bit bindsSequential impact timing delivers timed hammering during rotation to minimize overlapping bit impacts for up to 50% faster drillingAutomatic brush cut-off protects commutator from damage for longer tool life2-mode operation for Hammering Only or Hammering with Rotation for multiple applicationsNo hammering when idling function helps increase tool lifeHigh quality aluminum housing for greater durability and longer tool lifeMakita Motor Advantage engineered with field core interlocking steel laminations, dual ball bearing armature and more copper commutator bars, increasing energy transfer efficiency for more power and longer tool life