OBCORP LLC

United States

Four sizesSUNSHADE provides protection for single or multiple instruments, preventing instrument calibration drift due to temperature changes caused by solar radiation. Mechanical protectionSUNSHADE will shield instruments from the sun and provide partial protection from falling objects, rain, snow, and wind blown sand UV and corrosion resistantThe blended ABS material has excellent UV and corrosion resistance. Easy access to instrumentsSUNSHADE mounts to a standard 2" pipe stand and can be removed easily for full instrument access. SUNSHADES are part of our VIPAK line of instrument protection products and information can be found in the VIPAK brochure. Four sizesSUNSHADE provides protection for single or multiple instruments, preventing instrument calibration drift due to temperature changes caused by solar radiation. Mechanical protectionSUNSHADE will shield instruments from the sun and provide partial protection from falling objects, rain, snow, and wind blown sand UV and corrosion resistantThe blended ABS material has excellent UV and corrosion resistance. Easy access to instrumentsSUNSHADE mounts to a standard 2" pipe stand and can be removed easily for full instrument access. SUNSHADES are part of our VIPAK line of instrument protection products and information can be found in the VIPAK brochure. Four sizesSUNSHADE provides protection for single or multiple instruments, preventing instrument calibration drift due to temperature changes caused by solar radiation. Mechanical protectionSUNSHADE will shield instruments from the sun and provide partial protection from falling objects, rain, snow, and wind blown sand UV and corrosion resistantThe blended ABS material has excellent UV and corrosion resistance. Easy access to instrumentsSUNSHADE mounts to a standard 2" pipe stand and can be removed easily for full instrument access. SUNSHADES are part of our VIPAK line of instrument protection products and information can be found in the VIPAK brochure. Four sizesSUNSHADE provides protection for single or multiple instruments, preventing instrument calibration drift due to temperature changes caused by solar radiation. Mechanical protectionSUNSHADE will shield instruments from the sun and provide partial protection from falling objects, rain, snow, and wind blown sand UV and corrosion resistantThe blended ABS material has excellent UV and corrosion resistance. Easy access to instrumentsSUNSHADE mounts to a standard 2" pipe stand and can be removed easily for full instrument access. SUNSHADES are part of our VIPAK line of instrument protection products and information can be found in the VIPAK brochure.

Maintains freeze protection, close temperature tolerances or viscosity control.Excellent for maintaining long, continuous lengths of impulse lines and piping at consistent temperatures.Good for situations where steam is not available or steam supply could be interrupted, such as during shutdowns.

O'Brien TRACEPAK tubing bundle consists of a small diameter tube or group of tubes packaged in an insulated, weatherproofed jacket. It may be steam or electric traced to provide freeze protection or temperature maintenance. O'Brien tubing bundles provide the most economical and dependable solution for permanent installations. Whatever your application

O'Brien starts with select ASTM grade tubing and enhances its physical characteristics to improve dry-down, adsorption and corrosion resistance. We do this by controlling surface roughness, cleanliness, surface chemistry and reactive contaminants. TrueTube is available in orbital weld fittings, striaght sticks and long continuous lengths of electropolished (TrueTube EP) and electropolished tubing with a deactivated fused silica lining (TrueTube EPS).

Specifying the right tubing bundle for analyzer applications involves specific information about: Composition of the sample under all conditions.Sample Cycle - Acceptable Delay.Sample Dew Point or Freeze PointSample Temperature Extremes.Ambient Temperature Extremes.Heating Media Available.Installation Location - circuit length and area classificationSample System Design - fast loop

Six sizesWith a choice of six sizes you can select a steam heater that will provide freeze protection in the winter without overheating the instrument in the summer. Freeze protection or temperature maintenanceThese heaters have been thoroughly tested in our in-house environmental chamber to verify design calculations so that reliable predictions can be made for both low and high ambient conditions. If you need to maintain precise temperatures you can use the heater control valve (HCV) to control the enclosure temperature. It is available with standard 50F (10C) and 100F (40C) set-points. It can also be ordered for special set-point requirements. Corrosion resistant and efficient Constructed from stainless steel tubing and carbon steel fins, each unit is coated with a nickel-chrome alloy after assembly. OBrien steam heaters combine corrosion resistance and heat transfer efficiency in one unit. Simple connections and installationStainless steel mounting hardware is standard with all steam heaters. They fasten the heater to the instrument mounting bracket in the enclosure. The U-bend shape of the heater simplifies connecting the steam supply and condensate return to the 38" NPT fittings.

Light tracing (TPL) places a measure of insulation between the steam tracer and the process tube. It is generally used to provide freeze protection for instrument impulse lines and process lines for analyzers. Light steam tracing provides protection over a longer length than than heavy traced designs.

-LINE is used in applications where additional protection is required. J Line is not insulated or heated. J-Line tubing is ideal for pneumatic and hydraulic applications. Industry standard tubing coated with OBrien SV47 polymer provides increased protection cushioning the tube against wear from vibration. J-Line is supplied in long continuous coils that eliminate intermediate fittings every twenty feet (six meters). This reduces the number of potential leaks points in a single tubing run from 50 to over 90%. UsesInstrument airPneumatic process control linesMunicipal water wellsDown-hole chemical injectionChemical injectionSeal water feed linesDirect burialWindblown sand

S-LINE is designed specifiically for liquid and gas transport lines where heat loss and personnel protection and heat loss are important. S-LINE offers an inexpensive alternative to field insulation and weatherproofing of small diameter lines. Typical ApplicationsSteam supply linesCondensate return linesSmall diameter process linesProduct FeaturesPersonnel protectionWeatherproofingEnergy conservationJacketSV47 PVCUV resistantInsulationFibrous GlassWater soluble chloride < 45 ppm averageNon-hygroscopic

T-Series enclosure heaters are designed with standard redundant internal protection for long trouble free operation. The T-Series heater provides approved hazardous area heaters for a wide range of applications from instrument freeze protection to temperature maintenance for analytical applications. The system is highly configurable and includes redundant internal protection for long trouble free operation. Standard temperature ratings and operating voltages are listed below. The T-Series heater can be configured for vertical and horizontal installation with maximum efficiency. It is available in two base sizes and variable fin area depending upon wattage and maintain temperature. This heater series is available in T2, T3 and T4 temperature ranges to meet the needs of your area classification. It can be supplied with a factory set tamper proof temperature switch or connected to an existing or customer supplied controller. The standard junction box volume can be increased to accommodate other wiring connections such as impulse line heater cables. Specifications Wattage Up to 400 watts unit for T3, Up to 600 watts unit for T2 Supply Voltage 115, 230 and 277VAC (special order 12 & 24VDC, and 100 & 208VAC) Classifications NEC & CSA: Class I Division 1 Group A, B, C, & D (T2 or T3; ATEX Zone I EEx d IIC T3), Mounting Variable positioning Control Options Tamper Proof Thermostat - 50F10C, 75F25C, 100F40C, 125F50C, 150F6 T-Series enclosure heaters are designed with standard redundant internal protection for long trouble free operation. The T-Series heater provides approved hazardous area heaters for a wide range of applications from instrument freeze protection to temperature maintenance for analytical applications. The system is highly configurable and includes redundant internal protection for long trouble free operation. Standard temperature ratings and operating voltages are listed below. The T-Series heater can be configured for vertical and horizontal installation with maximum efficiency. It is available in two base sizes and variable fin area depending upon wattage and maintain temperature. This heater series is available in T2, T3 and T4 temperature ranges to meet the needs of your area classification. It can be supplied with a factory set tamper proof temperature switch or connected to an existing or customer supplied controller. The standard junction box volume can be increased to accommodate other wiring connections such as impulse line heater cables. Specifications Wattage Up to 400 watts unit for T3, Up to 600 watts unit for T2 Supply Voltage 115, 230 and 277VAC (special order 12 & 24VDC, and 100 & 208VAC) Classifications NEC & CSA: Class I Division 1 Group A, B, C, & D (T2 or T3; ATEX Zone I EEx d IIC T3), Mounting Variable positioning Control Options Tamper Proof Thermostat - 50F10C, 75F25C, 100F40C, 125F50C, 150F6 T-Series enclosure heaters are designed with standard redundant internal protection for long trouble free operation. The T-Series heater provides approved hazardous area heaters for a wide range of applications from instrument freeze protection to temperature maintenance for analytical applications. The system is highly configurable and includes redundant internal protection for long trouble free operation. Standard temperature ratings and operating voltages are listed below. The T-Series heater can be configured for vertical and horizontal installation with maximum efficiency. It is available in two base sizes and variable fin area depending upon wattage and maintain temperature. This heater series is available in T2, T3 and T4 temperature ranges to meet the needs of your area classification. It can be supplied with a factory set tamper proof temperature switch or connected to an existing or customer supplied controller. The standard junction box volume can be increased to accommodate other wiring connections such as impulse line heater cables. Specifications Wattage Up to 400 watts unit for T3, Up to 600 watts unit for T2 Supply Voltage 115, 230 and 277VAC (special order 12 & 24VDC, and 100 & 208VAC) Classifications NEC & CSA: Class I Division 1 Group A, B, C, & D (T2 or T3; ATEX Zone I EEx d IIC T3), Mounting Variable positioning Control Options Tamper Proof Thermostat - 50F10C, 75F25C, 100F40C, 125F50C, 150F6 T-Series enclosure heaters are designed with standard redundant internal protection for long trouble free operation. The T-Series heater provides approved hazardous area heaters for a wide range of applications from instrument freeze protection to temperature maintenance for analytical applications. The system is highly configurable and includes redundant internal protection for long trouble free operation. Standard temperature ratings and operating voltages are listed below. The T-Series heater can be configured for vertical and horizontal installation with maximum efficiency. It is available in two base sizes and variable fin area depending upon wattage and maintain temperature. This heater series is available in T2, T3 and T4 temperature ranges to meet the needs of your area classification. It can be supplied with a factory set tamper proof temperature switch or connected to an existing or customer supplied controller. The standard junction box volume can be increased to accommodate other wiring connections such as impulse line heater cables. Specifications Wattage Up to 400 watts unit for T3, Up to 600 watts unit for T2 Supply Voltage 115, 230 and 277VAC (special order 12 & 24VDC, and 100 & 208VAC) Classifications NEC & CSA: Class I Division 1 Group A, B, C, & D (T2 or T3; ATEX Zone I EEx d IIC T3), Mounting Variable positioning Control Options Tamper Proof Thermostat - 50F10C, 75F25C, 100F40C, 125F50C, 150F6 T-Series enclosure heaters are designed with standard redundant internal protection for long trouble free operation. The T-Series heater provides approved hazardous area heaters for a wide range of applications from instrument freeze protection to temperature maintenance for analytical applications. The system is highly configurable and includes redundant internal protection for long trouble free operation. Standard temperature ratings and operating voltages are listed below. The T-Series heater can be configured for vertical and horizontal installation with maximum efficiency. It is available in two base sizes and variable fin area depending upon wattage and maintain temperature. This heater series is available in T2, T3 and T4 temperature ranges to meet the needs of your area classification. It can be supplied with a factory set tamper proof temperature switch or connected to an existing or customer supplied controller. The standard junction box volume can be increased to accommodate other wiring connection