Rapp Industrial Sales

United States

18", 14", 38" & 12" Shank Mandrels Diamond or CBN platedHigh Speed Diamond or CBN plated Jig Grinding MandrelsHigh Speed Milling, Grinding Tools, Gold-ABN plated Jig Grinding Mandrels etc.Gold-ABN plated Jig Grinding MandrelsThe SALT-Superabrasives Specially Designed Spiral Tool for Internal and Jig Grinding, Diamond or CBN platedHigh Speed Milling, Grinding Tools Diamond or CBN plated18" Shank Shaped Tools 2" O.A.L. Diamond or CBN plated

Item Type CAT50 Face Mill HolderTaper CAT50ArborPilot Diameter (D2) 2Overall Length (L) in 7.3Gage Length (L1) in 2.4ArborPilot Length (L2) in 1516Drive Key (L4) in 34Major Diameter (D1) in 4.88 Weight lb 13.2Manufacturer Model Number 73822012 Mega Catalog Page 543

Item Type CAT50 Face Mill HolderTaper CAT50ArborPilot Diameter (D2) 2-12Overall Length (L) in 9.1Gage Length (L1) in 4ArborPilot Length (L2) in 1-18Drive Key (L4) in 1Major Diameter (D1) in 5.06 Weight lb 18.5Manufacturer Model Number 73822012 Mega Catalog Page 543

Item Type CAT40 Collet HolderCollet Type ER16Gage Length (L1) in 4Nut OD (D1) 28mm Clamping Range 132 - 1332Nut Style HexNut Thread M22 x 1.5Adjusting Screw Size 716-16 x 12"Flange Screw Size M4 x .7 x 4mmBalanced G6.315, 000Coolant ADBFlange Screw Part Number 8-815-180Nut Part Number 8-800-016Wrench Part Number 8-810-016Adjusting Screw Part Number 8-815-016

Taper CAT40Collet Type TG100Clamping Range 332 - 1Major Diameter (d) in 2-12Gage Length (L1) in 3Weight lb 3.7Balanced RPM 7000 Manufacturer Model Number 76142012 Mega Catalog Page 538, 579

Place the DIA-TRUpin vertically in a holding device (vice) and place it in front of the center line of the wheel to be trued.2. Turn off the coolant on your machine.3. Touch off with the wheel to be dressed at the highest point of the DIA-TRUpin.4. Move the wheel across the pin using a moderate to fast feed rate.5. Use a down feed of .004 (on very thin or fine grit wheel take a smaller down feed) and feed the wheel to be dressed across the DIA-TRUpin.6. Take multiple passes with the initial down feed and then reduce the down feed to .003" .002" .001" .0005" and less. Progressively reducing the down feed will minimize "crowning" of the wheel being trued or reconditioned.

Item Type CAT40 Collet HolderCollet Type ER11Gage Length (L1) in 3Nut OD (D1) 19mm Clamping Range 132 - 14Nut Style HexNut Thread M14 x .75Adjusting Screw Size 516-18 x 12"Flange Screw Size M4 x .7 x 4mmBalanced G6.315, 000Coolant ADBFlange Screw Part Number 8-815-180Nut Part Number 8-800-011Wrench Part Number 8-810-011Adjusting Screw Part Number 8-815-011

The Design.The innovative design of the Murkens Gage makes it one of the most rigidbases you will ever use.This rigidity greatly increases the repeatability of your indicator whiledecreasing the number of adjustments necessary during use. The simplicity ofthe mechanism results in fewer moving parts to repair or replace.The overall performance of this gage is most impressive. The Features.* Spring steel front for rigidity.* Hardened -40 screw with extra-long brass bushing.* Blackened for appearance and rust resistance.* Built-in bar for checking squareness.* Hardened bottom with dirt grooves.* Large diameter adjusting knob for sensitivity.* Wrench hole in end of chromed rod for tighteningloosening.* Spring-loaded indicator rod prevents nose-diving.* 7-12" chromed rod for tall work pieces.