TANDEMLOC, Inc.

United States

Our Most Economical Load Leveling Sling. These economical sling assemblies allow the user to lift from the bottom corner fittings and adjust for off-center loads in both longitudinal and transverse directions. They are compact and easy to store and ship.WORK LOAD LIMIT (WLL): 30 Long Ton (67, 200 lb)PROOF TESTED: Beam - Proof tested to 125% of work load limit. Chain and fittings - Tested to 200% of their rated WLL.WEIGHT:-299 - 1, 223 LB., 1, 409 LB. with PC 9-400C - 1, 534 LB., 1, 720 LB. with PC 9.STANDARDS: Specification #EAD21000A applies.MATERIAL AND FINISH: Steel with safety yellow paint. Chain & connector link pinsspacers are not painted.

Height Extenders "extend" the height of the corner fitting compensating for projections above the container corner. These Extenders are available in a variety of heights and are proof tested. Heights available from 6" to 60".Lift work load limit is 7.5 L.T. (16, 800 LB) @ 3:1 Safety Factor to yield. Conforms to ANSI B30.20.PROOF TESTED: Each assembly is proof-tested to two times work load limit (2 x WLL) and certified.*NOTE: Uniform compression strength rating @ safety factor of 1.8 to ULT. is 118, 000 LB. horizontal strength rating is in chart (L).MATERIALS: Steel, painted yellow.DIMENSIONS: Subject to manufacturing tolerances.STANDARDS: Specification #EAD21000A applies.

Introducing Tandemloc's most economical bottom lift container sling for the most economical way to lift your ISO container. ISO 3874 standards require that when lifting containers from the bottom corner fittings, a lift sling must be used. Tandemloc has designed and manufactured a simple and economical lift sling that meets the ISO 3874 standards. The 20'version comes in two different working load strengths. The 20'40'version is versatile because it can be easily adjusted to lift a 20'or 40'container. Is your working load capacity not listed? Just give one of our sales staff a call and we can customize the capacity to meet your strength requirements.WORK LOAD LIMIT (WLL): See Chart BelowPROOF TESTED to 125% of WLL (See Chart Below) Proof Test Certificate providedCALCULATED WEIGHT: See Chart BelowMATERIAL AND FINISH:PC1 - Steel, PaintedPC2 - Steel, BrightPC3 - Steel, PaintedSTANDARDS: Specification #EAD21000A applies.GENERAL: All containers, corner fittings and sling equipment to be inspected for flaws and damage before use. Only equipment in good condition shall be lifted.In some cases, ISO container measured lengths differ from size "l". Ref. I.S.O. STD. 668.20'40'combo slings have short wire rope legs for a 20'lift & four wire rope extensions for a 40'lift.

The T42000C series Tiedown features a "screwdown" shallow depth ISO Twistlock and two Mil Std 209 Tie downs. .all within one cast steel weldable housing. This tiedown is beneficial when space is at a premium. See the T12000D Tiedown to compare depth space requirements. This very shallow design incorporates all of the same features as the T12000D, including a mechanism to prevent unwanted "unscrewing" or loosing while the vehicle is traveling over rough terrain. This product is fully galvanized, but we removed the galvanize at the weld zones. A wrench is available but purchased separately.Kits are shipped unassembled except PC#1 which is partially assembled per dwg. ST42001B.No grease is used to allow for future paint.Locate connectors per "male fitting instructions" on Tandemloc Data Sheet DF-72047-16 (Sheet 2) for standard sized structures.

The 24' Autoloc Container Lift Spreader is sized to lift what is commonly referred to as "Matson" 24-foot Containers. Containers must be outfitted with ISO 1161 Corner Fittings in order to be compatible with this spreader.TANDEMLOC can build Autoloc Spreaders for specialty containers that use these corner fittings yet do not meet the overall box dimensions or capacities as specified by ISO 668.See other models: 40' - 20' - 12' Mini Container - Custom Lengths AvailableWORK LOAD LIMIT (WLL): 70, 528 LBPROOF TESTED 125% (88, 160 LB) of WLLCALCULATED WEIGHT: 3, 200 LBFINISH: Sandblasted, primed and painted safety yellow.STANDARDS: Specification #EAD21000A applies. Spreader meets or exceeds AISC fatigue life of 600, 000 cycles.Auto-actuated spreader unlocks when spreader is first lifted then locks when lowered and lifted again, alternating with each cycle (shown in locked position.)CUSTOM OPTIONS: Lifter can be customized for your application, inquire for other load capacities or sizes.Click here for Lift Beam that turns your Autoloc into a Non-Containerized Cargo Lifter.Emergency Gear Attachment

This device is commonly used to stack and lock ISO containers. The "double cone" Twistloc has been a staple in the maritime intermodal business for decades. Order No. AD54000A-1GA.LightweightHigh quality all steel constructionFINISH: Hot-dip galvanizedCalculated Weight: 11.7 LBBreakload: Tension 50 Tons, Shear 40 Tons

For applications that require ISO Shelters or Containers to sit level on uneven surfaces, the ISO Container Leveling Legs are the solution. The legs can be rigidly connected to the side or end hole of bottom ISO corner fittings found on ISO Shelters or Containers. Each leg can be individually adjusted in 14 inch increments up or down, with a total adjustment range of 12 inches per leg on the -2PG, 25" for the -3PG. These are very heavy duty units and incorporate our 12905BA Horizontal Clamp Connector for a rigid, clamped connection to the sheltercontainer.

Lift Lug - Designed for VERTICAL Lifting from the Top Corner Fitting of ISO Containers Can be used with a master link for your sling hook (1PA model) or without (2PA model). According to ISO 1496 and ISO 3874, when lifting containers from the top corner fittings, the forces must be vertical to prevent compressive loading to the top rail of the container. Prior to any lifting, it is the user's responsibility to know and be familiar with the limitations of the container or ISO configured shelter.WLL: 25, 000 Lb. Maximum Per Lug Working Load LimitWEIGHT: 29 LBS.AVAILABLE: for any ISO container. Bearing area conforms to ISO 3874 - 1984 (E)PROOF TESTED to 50, 000 Lbs. (Each Lug)STANDARD: Specification #EAD21000A applies

Replacement Rotary Lift Lug - Designed to Connect Lift Slings to Bottom Apertures on ISO 668 Container Corner Fittings (ISO 1161) The Replacement Rotary Lift Lug with Safety Lock has an additional safety feature to help prevent the lug from accidental dislodgement under unstable conditions (while not under load). It should be used in areas where it is not practical to have personnel standing by to insure that the 90 interlock of the toe in the corner fitting is maintained prior to lifting.ORDER NO: 416000C-LSTZW: Replacement Rotary Lift LugWLL: 33, 600 LB.PROOF TESTED to 2x WLL.WEIGHT:-LSTZW Assembly: 22.3 LB.416005B-1TZK Kit: 6.3 LB.STANDARD: Specification #EAD21000A applies,

The TANDEMLOC Autoloc Spreader makes container lifting simple. Easy operation lets you get the job done, saving you time and money. Superior convenience and operation makes it plain to see that the Autoloc is the choice for your container lifting applications. Also available in a 24' Model.WORK LOAD LIMIT (WLL): See chart below.PROOF TESTED: 125% of WLL, wproof test certificate.CALCULATED WEIGHT: See chart below.FINISH: Sandblast, prime and paint safety yellow.STANDARDS: Specification #EAD21000A applies. Spreader meets or exceeds AISC fatigue life of 600, 000 cycles.OPERATION: Simple mechanical operation - no electronics or hydraulics. Twistlocks lock unlock when sling wires are slackened. More convenient to use than manual spreaders - no ground personnel required to lock unlock twistlocks. 4 Leg wire rope sling standard. Wire rope rigging has a "Flemish Eye" style termination point, which has been found to be most reliable and recommended by FEMA over any other style termination point. Built-in "Indicator Flags" allow the crane operator to easily locate the spreader onto the waiting container. And our ratchet-style gearbox provides the user with operational confidence as it has been field proven since 1993.CUSTOM OPTIONS: Lifter can be customized for your application, inquire for other load capacities or sizes.Click here for Lift Beam that turns your Autoloc into a Non-Containerized Cargo Lifter.Emergency Gear Attachment

Introducing Tandemloc's most economical bottom lift container sling for the most economical way to lift your ISO container. ISO 3874 standards require that when lifting containers from the bottom corner fittings, a lift sling must be used. Tandemloc has designed and manufactured a simple and economical lift sling that meets the ISO 3874 standards. The 20'version comes in two different working load strengths. The 20'40'version is versatile because it can be easily adjusted to lift a 20'or 40'container. Is your working load capacity not listed? Just give one of our sales staff a call and we can customize the capacity to meet your strength requirements.WORK LOAD LIMIT (WLL): See Chart BelowPROOF TESTED to 125% of WLL (See Chart Below) Proof Test Certificate providedCALCULATED WEIGHT: See Chart BelowMATERIAL AND FINISH:PC1 - Steel, PaintedPC2 - Steel, BrightPC3 - Steel, PaintedSTANDARDS: Specification #EAD21000A applies.GENERAL: All containers, corner fittings and sling equipment to be inspected for flaws and damage before use. Only equipment in good condition shall be lifted.In some cases, ISO container measured lengths differ from size "l". Ref. I.S.O. STD. 668.20'40'combo slings have short wire rope legs for a 20'lift & four wire rope extensions for a 40'lift.

The T42000C series Tiedown features a "screwdown" shallow depth ISO Twistlock and two Mil Std 209 Tie downs. .all within one cast steel weldable housing. This tiedown is beneficial when space is at a premium. See the T12000D Tiedown to compare depth space requirements. This very shallow design incorporates all of the same features as the T12000D, including a mechanism to prevent unwanted "unscrewing" or loosing while the vehicle is traveling over rough terrain. This product is fully galvanized, but we removed the galvanize at the weld zones. A wrench is available but purchased separately.Kits are shipped unassembled except PC#1 which is partially assembled per dwg. ST42001B.No grease is used to allow for future paint.Locate connectors per "male fitting instructions" on Tandemloc Data Sheet DF-72047-16 (Sheet 2) for standard sized structures.