Post Buy Requirement
UK
.California., United States
Add Review

Hangers

Super Hanger

  • Dimension (LxWxH) 16.60 in x 1.20 in x 9.00 in 42.16 cm x 3.05 cm x 22.86 cm
Super Hanger
Super Hanger
When the average hanger just doesnt cut it, rely on the Super Hanger. We know your gear is often heavy and wet. So, we built the Super Hanger sturdy, with high quality non-corrosive materials. It holds more weight, so your valuable stuff wont end up on the ground.
This sturdy non-corroding hanger will support wet and dry suits during drying and storage.

One piece I-beam construction for strength.
Non-corroding plastic resin will not rust
Supports up to 20 pounds
Proudly made in the USA
View Complete Details

Super BC Hanger

  • Dimension (LxWxH) 16.00 in x 1.20 in x 10.00 in 40.64 cm x 3.05 cm x 25.40 cm
Super BC Hanger
Super BC Hanger
Finally, a hanger designed specifically for holding a BC Vest and regulator during drying and stoarge. It is built sturdy with high quality non-corrosive materials for safe drying.

The Super BC Hanger is also ideal for use with police vests, body armor and bulletproof vests. Due to its expert design, your gear fits on it easily, for a no-hassle drying and storage solution.
One piece I-beam construction for strength.
Non-corroding plastic resin will not rust
Supports up to 20 pounds
Proudly made in the USA
View Complete Details

Super BC/Regulator Hanger

  • Dimension (LxWxH) 16.00 in x 1.20 in x 10.00 in 40.64 cm x 3.05 cm x 25.40 cm
Super BCRegulator Hanger

The UK Super BC Regulator Hanger holds US Yoke and European DIN fittings for hanging your regulator.

The hanger was created to make it easy for you to hang up all your gear in one spot. Holds up wetsuits, scuba suits, or heavy turnout gear with ease. Supports up to 50lbs.

Made with care in the USA.
One piece I-beam construction for strength
DIN and Yoke Holders for Regulator
Non-corroding plastic resin will not rust
Proudly made in the USA
View Complete Details

Exposure Suit Hanger

  • DIMENSIONS (L W H) 21.50 in x 7.00 in x 14.20 in 54.61 cm x 17.78 cm x 36.07 cm
Exposure Suit Hanger 5.0
Exposure Suit Hanger 5.0
The Exposure Suit Hanger is built to optimally dry and store the heaviest gear. Its 5 inch shoulder width and heavy duty stainless steel hook will support over 100 pounds of outerwear. Its designed to hold open suits, vests and gear for improved air circulation while drying. Its durable, broad shoulder also prevents creases and damage to foam suit material and seams.
This 5 inch shoulder width hanger will support over 100 pounds of outer wear for drying or storage.
The hook is made from heavy duty stainless steel and the molded ABS resin shoulder form is highly impact resistant.
Wet suits, dry suits, heavy winter gear, tactical vests, turnout gear, etc. are held open for good air circulation while drying.
The broad shoulder also prevents creases in that area which can cause damage to foam suit material.
Proudly made in the USA
View Complete Details

Gorilla Big Gear Hanger

  • DIMENSIONS (L W H) 18.50 in x 1.20 in x 10.50 in 46.99 cm x 3.05 cm x 26.67 cm
Gorilla Big Gear Hanger

Gorilla Tough For Gorilla Size Gear! As itss name implies, the Gorilla Hanger is made for hanging heavy or bulky outer gear such as wet suits, protective vests, snow gear, bunker gear, etc. The beefy wide hook makes it easy to carry the fully loaded hanger without damaging your hand.

Wondering how to dry heavy gear? Slots imbedded in the shoulder keep straps from vests or pant suspenders from sliding to the ground. Bulky pants are easily draped over the bottom cross bar, due to the extra large central opening. Salt or fresh water will not corrode or harm the high impact resin from which the Gorilla hanger is molded. Rigid I-beam construction prevents the 1-inch thick frame from flexing and allows it to support over 50 pounds.

The Gorilla Hanger is a definite must for organizing and protecting expensive sports and work gear by keeping it off the floor and out in the air for quick drying and storage.
Shoulder strap notches keep garments from sliding off
Extended handle fits comfortably in the palm of your hand
3 inch opening accommodates bulky pants etc.
Supports over 50 pounds
View Complete Details

Super Accessory Hanger

  • Dimension (LxWxH) 13.00 in x 1.20 in x 20.00 in 33.02 cm x 3.05 cm x 50.80 cm
Super Accessory Hanger
Super Accessory Hanger
Our uniquely designed hanger holds your dive gloves, hood, fins, and booties. The Super Accessory Hanger is an effective solution for drying your gear after a dive and protecting it from damage on the floor.
One piece I-beam construction for strength.
Non-corroding plastic resin will not rust
Supports up to 20 pounds
Proudly made in the USA
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • NANCY STRZEPEK (UNDERWATER KINETICS)
  • 13400 Danielson Street, Poway, .California., United States
  • Share us via