Our Products #5146735

Part Number LTIH-5004WPower (W) 5000Voltage (V) 54 - 66Current (A) 85MinMax (A) 7692Ignition Voltage (kV) 36Min. Opern Circuit Voltage (V) 85110Cooling (ftsec) 20Diameter d (mm) 86.5Length c max. (mm) 349Length b max. (mm) 307Distance a (mm) 143Ferrule length f (mm) 70Arc gap (cold) g (mm) 8.24Lamp Life (hours) 750Distribution wavelength (nm) 365, 405, 436Operating position Vertical 10Anode base 38 - 9.4Cathode base 38 - 7.9

1. Capillaries are a Graded Seal Lamp, making this product impossible to hear in an annealing process. The quartz at the graded ends of the lamp has a lower melting point than the quartz body. The annealing process heats the lamps in a furnace for a given period of time. This process relieves the stress during the lamps manufacturing process. The lack of annealing results in a lamp that is very fragile requiring great care in installation. 2. The ON and OFF cycling of the lamp is temperature related. Capillary lamps are designed for intermittent operation only. The longer or hotter the burn period the shorter the lamp life. Typical life rating is 7000 shots at 40 seconds or less, 3000 shots for over 40 seconds. If the ON cycle is extended, the lamps internal pressure increases, as well as the potential for violent lap failure. It the OFF time is too short, the rise time into the mercury vaporization may be effected and the migration of the mercury away from the electrode to the center of the lamp will be inevitable. This will result in lamp instability and dark electrodes, resulting in early failure and possible lamp explosion. 3. It is critical for proper ignition to manually distribute the mercury into even pools at each end of the lamps in front of the electrodes (see instructions included with each lamp). If the mercury is not properly distributed, the operation ONOFF time may be affected, resulting in a hard-starting lamp which could fail or explode causing short life. As this lamp had a graded seal, there is a large dead spaced behind the electrode tip. This space must be filled to allow a certain portion of mercury to enter into ionization. If all the mercury does ionize, the lamp becomes saturated. Mercury Saturation resulting from an unbalanced lamp will cause unstable current regulation. IT IS VERY IMPORTANT TO BALANCE THE MERCURY! 4. Capillary lamps rated over 1KW require water-cooling. The user must evaluate the rated GPH for the required wattage. Water must be deionized and checked and changed frequently to eliminate ion concentration. Mechanical equipment must be checked frequently for water leaks and gasket failure. 5. Many lamps are returned for breakage during installation. As the lamps end is nickel-plated and the spring load in the system is the same, the lamp must be carefully installed to eliminate the lamps from slopping to one side from the two polished surfaces. This will result in a lamp slightly cocked to one side in the water jacket. This creates a thermal stress when the lamp is heated resulting in hairline cracks in the lamp body and early failure.

The ULS ULXS1600G244 is a DC-Controlled lamp that is specifically designed for applications requiring excellent ARC stability and high light output.Current Control Range (A.D.C.) 58 - 65Average Lumen Output (LM) 56, 000Luminous Intensity (LM) 5, 800Burning Position H2820 - V20Forced Air Cooling (msec.) 10 - 13Base - Pin or Thread (mm) Anode (+) 28-5 X 3 pinsCathode (-) 28 - 9.5

The ULS ULXS500R244 is a DC-Controlled lamp that is specifically designed for applications requiring excellent ARC stability and high light output. Current Control Range (A.D.C.) 20 - 28Average Lumen Output (LM) 16, 500Luminous Intensity (LM) 1, 700Burning Position H2820 - V20Forced Air Cooling (msec.) 4 - 6Base - Pin or Thread (mm) Anode (+) 19 - 4Cathode (-) 25 - 9.5

There are many Quartz Halogen styles used for various applications, we have many of them in stock. These lamps are commonly used for studio, theater, TV & videoAny tungsten filament lamp can be used as an infrared heat source. The most practical are quartz halogen lamps. Tubular and reflector lamps have been most successful. Tubular quartz lamps are available in a number of wattages and voltages which allows for ramping using variacs or simple dimming devices. Available in dichroic (thin film) reflectors or highly efficient gold coating, allows for various beam distributions, wattages, and voltages. Special high temp sockets and transformers available from inventory for optical package. (Ellipsoidal-designed reflector develops up to 1500C 19mm in front of lamp face.)

Deuterium lamps create an arc between the anode and tungston filament that excites molecular deuterium. Light is emmitted as it transitions back to it's initial state. The intense continuum from the vacuum ultraviolet to 500 nm, and the low visible and infrared output, ensure superior signal to noise for many UV measurements. We stock a number of different models from Heraeus, Hamamatsu and others, including part numbers: L1789, DO801, DO302, DO902, D1050, R.23, G.03, 3UNXGa, 5QNCu-Zn, Cu, Pb, As and Hollow Cathode.

Power (W) 5000Voltage (V) 47 - 53Current (A) 100MinMax (A) 95105Ignition Voltage (kV) 36Min. Opern Circuit Voltage (V) 85110Cooling (ftsec) 20Diameter d (mm) 86.5Length c max. (mm) 349Length b max. (mm) 307Distance a (mm) 143Lead length e (mm) 260Ferrule length f (mm) 70Arc gap (cold) g (mm) 7.52 Lamp Life (hours) 750Distribution wavelength (nm) 365, 405, 436Operating position Vertical 10Anode base 38 - 9.4Cathode base 38 - 7.9