Laboratory Equipments #5146677

GPMPSI:
Fluid:
Manufacturer: N.A.
HP:
Shown as: N.A.
NSN: 4920-923-1218
Product Type: Test Stand
Type:
Part No: 12A2606-1
Model No:

Manufacturer: General DynamicsLockheed Martin
Cage: 81755
Originally designed as F14 wing sweep actuator tester can be adopted for other aircraft and ball screws rotary mechanical testing.

DescriptionFunction of unit

Capable of testing linear and rotary actuator with 52, 000LB tension compression load.

The test bed is a 16" x 8" I beam 138" L with a hydraulic load cylinder mounted at one end and hydraulic pump motor mounted at the other end.

Test set will require a small hydraulic power supply for the ball screw motor and the load circuit. Unit is currently set up for Mil-H-5606 or equal fluid. (Skydrol on request)

The control panel consists of the following;

1 Torque test gear box valve
1 52, 000 lb compression valve
1 52, 000 lb tension valve
1 Cylinder extend or retract 4 way valve
1 Actuator extend or retract 4 way valve
1 3000 PSI cylinder pressure 4" gauge
1 Overhaul test valve
1 6000 PSI pump pressure 6" gauge
Fixture Assembly - Test wing sweep actuator
Load Cylinder - Mfg Ortman Miller, serial number 329795, 2TH ER HYD. 6 x 34
Test bed clevis to clevis 89" extended retract 61"
Filtration - Bendix filter division rating 50 GPM, serial 3499, replacement fuse # 043589-5
Gauges - 6", 6000 PSI & 4", 3000 PSI
Rotary Hydraulic power Denison Motor - Model MF05-020-31N-001, 3500 PSI, max. RPM 3000


Approx. Dimensions:
ALS ID: TSL-101JVV
Approx. Weight:
Location:

GPMPSI:
Fluid:
Manufacturer: American Lab & Systems (ALS)
HP:
Shown as: N.A.
NSN:
Product Type: Test Stand
Type:
Part No:
Model No:

ALS No: 12678
Special Note: USED TO TEST ALLIED SIGNAL & HONEYWELL PART NUMBER 12784

DescriptionFunction of unit

CDU Test Stand to test ball screw drive assemblies. The test stand will consist of a load work station with control valves, regulators, transducers, load cylinder, solenoid valves, test shield, cable harness, pressure control valves, pressure gauge, all controls and instruments will be located in the right hand front sloped panel.

The CDU Test Stand will include electronic digital displays, x-y plotter, electronic control rack. The electronic rack will display torque, pressure load the main. The main fixture is included this is a manualautomatic test stand with stand alone.

The finished two (2) piece system with control station and fixture in one (1) frame electronics cabinet is 19" rack style 5' ft high.

The harness will be approximately 15' ft and connect the two (2) units together.

A complete manual is provided with unit. Call for more information and price.


Approx. Dimensions:
ALS ID: TSCSD-103
Approx. Weight:
Location:

GPMPSI:
Fluid:
Manufacturer: N.A.
HP:
Shown as: N.A.
NSN:
Product Type: Test Stand
Type:
Part No:
Model No: 205975

Manufacturer: Woodward Governor Co.
DescriptionFunction of unit

The test stand and accessory equipment have been designed to test most models of governors manufactured by Woodward Governors Company, and has the capability of testing governors manufactured by others.

The stand is driven by a reversible air motor. The speed of the stand is controlled by closed loop operation between the governor and the stand that is the governor controls the position of the air control valve which controls the air supply to the air motor. The air motor requires an air capacity of approximately 56 cubic feet per minute at a pressure of approximately 125 PSI to dive a governor at approximately 1500 RPM. The air motor can be adjusted up or down to accommodate different lengths of governor drive shafts.

The test stand incorporates a drop feed, oil mist lubricator to lubricate the air motor and to permit maintenance free operation.

Electrical power is required on the models with the instrumentation panel. The power requirement to each stand may vary to meet the needs of a particular installation. Normal power requirements are 230VAC, 3 phase, 50-60 cycles. The rail type stand has a DC power supply built into the control panel to provide power for checking solenoids and switches within the governor.

A heated oil system is provided in the rail and non-rail type stand to supply oil to the governors under test. The heaters mounted in the oil system sump are immersion type and thermostatically controlled. Temperature of the oil system is normally set to approximately 210F. The system uses SAE 30 non detergent lubricating oil at a preset pressure of approximately 75 PSI.

A vacuum system is provided in the rail type stand for testing the engine lubricating oil vacuum shut down device incorporated in some governors.

Leading Particulars

Testing Capability

Rail Type: All governors listed for non-rail type plus locomotive speed setting governors
Non Rail Type: SG, PSG, UG8, UG8PL, UG32, UG40, **PGA, PGD, PGL, PGPH, PGPL, PGTR, SI, *LSG10, EG3C, *EG3P, *EGB10, EGB2C, *EGB10C, EGB35C, EGB50C, *EGB2P, *EGB10P
Basic: UG8, UG32, UG40, PGD, PGL, SI, *LSG10, 8EGB10, WO

Air Supply Required

Rail Type: 56 CFM @ 125 PSI
Non Rail Type: 56 CFM @ 125 PSI
Basic: 56 CFM @ 125 PSI

Electrical Power Requirements

Rail Type: 230 VAC, 3 PH, 5060 cycle with external ground
Non Rail Type: 230 VAC, 3 PH, 5060 cycle with external ground

Oil Supply Type

Rail Type: 30 SAE
Non Rail Type: 30 SAE

Pressure Output

Rail Type: 75 PSI
Non Rail Type: 75 PSI

Controlled Temperature Output

Rail Type: 210F
Non Rail Type: 210F

Capacity

Rail Type: 9 gallon
Non Rail Type: 9 gallon

Filter Elements

Rail Type: 50 micron
Non Rail Type: 50 micron

Air motor Lubrication

Rail Type: Drop feed auto. Lubricator and gear box fittings
Non Rail Type: Drop feed auto. Lubricator and gear box fittings
Basic: Drop feed auto. Lubricator and gear box fittings

Type Oil

Rail Type: 150-200 SU
Non Rail Type: 150-200 SU
Basic: 150-200 SU

Drip Rate

Rail Type: 3-5 dropsmin
Non Rail Type: 3-5 dropsmin
Basic: 3-5 dropsmin

Air Motor Rotation

Rail Type: CW or CCW governor control
Non Rail Type: CW or CCW governor control
Basic: CW or CCW governor control

Vacuum System

Rail Type: Installed


Approx. Dimensions:
ALS ID: TSPN-109
Approx. Weight:
Location:
Units Subject To Prior Sale

GPMPSI: 10 @ 3000
Fluid: Red Oil, Mil-H5606
Manufacturer: N.A.
HP: 20
Shown as: N.A.
NSN:
Product Type: Test Stand
Type: Component Test Stand
Part No:
Model No: 7564

Manufacturer: Air Hydraulic System Inc.
The test stand is used with Mil-H5606 or equal will test hydraulic valves, actuator, hoses, cylinders, and related hydraulic components include cycle valve, 10 micron filter, adjustable pressure control.

Vickers PVB10 (main pump)
Reliance 20 HP, 256T, 220440 Vac, 1760 RPM, stopstart switch electric motor
Vickers relief 0-3000 PSI, # CT06-F-40
Vickers panel mount adjustable relief # 175 series
0-20 GPM flowmeter by Universal Filter, Inc.
(2) each 1" low pressure filters
4 way valve, manual 3 position # DG17S4-018C-50
Gauge

1 ea. 2, 0-3000 PSI
2 ea. 4", 0-5000 PSI
1 ea. Flowmeter, 0-20 GPM

Work sink with drain 31" W x 23" D x 3", sink area has 3 each unitstrut channel weld in to facilitate securing of the object.
30 gallon reservoir with 2 cleanouts, level gauge, temperature gauge

Approx. Dimensions: 31" W x 34" D x 62" H
ALS ID: TSH-123
Approx. Weight: 900 lbs
Location: